b Maintenance and Service Guide Compaq Presario V2600 Notebook PC Document Part Number: 408525-001 March 2006 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures.
© Copyright 2006 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice.
Contents 1 Product Description 1.1 1.2 1.3 1.4 1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 Resetting the Computer. . . . . . . . . . . . . . . . . . . . . . . 1–4 Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–6 Design Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 1–20 2 Troubleshooting 2.1 Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . .
Contents 3 Illustrated Parts Catalog 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–1 Computer Major Components. . . . . . . . . . . . . . . . . . 3–2 Display Assembly Components . . . . . . . . . . . . . . . 3–12 Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . 3–14 Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–16 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 5 Removal and Replacement Procedures 5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2 5.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–3 5.3 Preparing the Computer for Disassembly . . . . . . . . . 5–4 5.4 Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6 5.5 Computer Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10 5.6 Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10 5.
Contents 6 Specifications A Connector Pin Assignments B Power Cord Set Requirements C Screw Listing D Display Component Recycling Index vi Maintenance and Service Guide
1 Product Description The Compaq Presario V2600 Notebook PC offers advanced modularity, Intel® Core Duo and Core Solo processors, and extensive multimedia support.
Product Description 1.1 Features ■ The following processors are available, varying by computer model: ❏ Intel Core Duo T2500 (2.00-GHz) ❏ Intel Core Duo T2400 (1.83-GHz) ❏ Intel Core Duo T2300 (1.66-GHz) ❏ Intel Core Solo T1300 (1.66-GHz) 1–2 ■ 14.0-inch WXGA (1280 × 768) TFT display with over 16.7 million colors, varying by computer model ■ 100-, 80-, 60-, or 40-GB high-capacity hard drive, varying by computer model ■ 256-MB DDR synchronous DRAM (SDRAM) at 533 MHz, expandable to 2.
Product Description ■ Support for ExpressCards ■ External 65-watt AC adapter with 3-wire power cord ■ 6-cell or 12-cell Li-Ion battery pack ■ Stereo speakers with volume up and down buttons ■ Support for the following optical drives: ❏ 8X Max DVD+RW/R and CD-RW Combo Drive ❏ 4X Max DVD+RW/R and CD-RW Combo Drive ❏ 8X Max DVD-ROM Drive ❏ 24X Max DVD/CD-RW Combo Drive ■ Connectors: ❏ External monitor ❏ Universal Serial Bus (USB) v. 2.
Product Description 1.2 Resetting the Computer If the computer you are servicing has an unknown password, follow these steps to clear the password. These steps also clear CMOS: 1. Prepare the computer for disassembly (refer to Section 5.3, “Preparing the Computer for Disassembly,” for more information). 2. Remove the real-time clock (RTC) battery (refer to Section 5.16, “RTC Battery,” for more information). 3. Wait approximately 5 minutes. 4. Replace the RTC battery and reassemble the computer. 5.
Product Description 1.3 Power Management The computer comes with power management features that extend battery operating time and conserve power.
Product Description 1.4 External Components The external components on the front of the computer are shown below and described in Table 1-1.
Product Description Table 1-1 Front Components Item Component Function 1 Speakers (2) Produce stereo sound. 2 Wireless light (select models only) On: An integrated wireless device is hardware enabled. 3 Power light ■ On: Computer is turned on. ■ Blinking: Computer is in standby. ■ Off: Computer is off. 4 Drive light On or blinking: The internal hard drive or an optical drive is being accessed. 5 Battery light ■ Amber: The battery pack is charging.
Product Description The external components on the right side of the computer are shown below and described in Table 1-2.
Product Description Table 1-2 Right-Side Components Item Component Function 1 USB connectors (2) Connect an optional USB device. 2 Memory Reader (select models only) In Windows, supports digital cards. 3 1394 port (select models only) Connects an optional 1394 device such as a scanner, digital camera, or digital camcorder. 4 Memory Reader light (select models only) On: A digital card is being accessed. 5 Optical drive Supports an optical disc.
Product Description The external components on the rear and left side of the computer are shown below and described in Table 1-3.
Product Description Table 1-3 Rear and Left-Side Components Item Component Function 1 Exhaust vent Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. User the computer only on a flat, hard surface. Do not allow a hard surface, such as a printer, or a soft surface, such as pillows, thick rugs or clothing, to block airflow. 2 Power connector Connects an AC adapter cable. 3 External monitor port Connects an optional VGA external monitor or projector.
Product Description The computer keyboard components on the computer are shown below and described in Table 1-4.
Product Description Table 1-4 Keyboard Components Item Component Function 1 fn key Combines with other keys to perform system tasks. For example, pressing fn+f7 decreases screen brightness. 2 caps lock key Enables caps lock and turns on the caps lock light. 3 f1 to f12 keys (12) Perform system and application tasks. When combined with the fn key, several keys and buttons perform additional tasks as hotkeys.
Product Description The computer top components on the computer are shown below and described in Table 1-5. Top Components, Part 1 Table 1-5 Top Components, Part 1 Item Component Function 1 Caps lock light On: Caps lock is on. 2 Display switch If the computer is closed while on, turns off the display.
Product Description Table 1-5 Top Components, Part 1 (Continued) Item Component Function 3 Wireless button Enables/disables an internal wireless device. Wireless light On: an integrated wireless device is hardware enabled. Power button When the computer is ■ Off, press to turn on the computer. ■ On, briefly press to initiate Hibernation. ■ In Standby, briefly press to resume from Standby. ■ In Hibernation, briefly press to restore from Hibernation. Power light ■ On: Computer is turned on.
Product Description The computer top components on the computer are shown below and described in Table 1-6.
Product Description Table 1-6 Top Components, Part 2 Item Component Function 1 TouchPad horizontal scrolling region Scrolls toward left side or right side. 2 TouchPad Moves the pointer. 3 TouchPad light On: TouchPad is enabled. 4 TouchPad on/off button Enables/disables the TouchPad. 5 TouchPad vertical scroll region Scrolls upward or downward. 6 Left and right TouchPad buttons Function like the left and right buttons on an external mouse.
Product Description The external components on the bottom of the computer are shown below and described in Table 1-7. Bottom Components Table 1-7 Bottom Components Item Component Function 1 Optical drive Supports an optical disc. 2 Battery pack release latch Releases a battery pack from the battery bay. 3 Battery pack Holds a battery pack.
Product Description Table 1-7 Bottom Components (Continued) Item Component Function 4 Exhaust vents (4) Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Use the computer only on a flat, hard surface. Do not allow a hard surface, such as a printer, or a soft surface, such as pillows, thick rugs or clothing, to block airflow. 5 Hard drive bay Holds the internal hard drive. 6 Mini Card compartment Holds an optional wireless LAN device.
Product Description 1.5 Design Overview This section presents a design overview of key parts and features of the computer. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps.
2 Troubleshooting Å WARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting Accessing Computer Setup The information and settings in Computer Setup are accessed from the File, Security, Tools, and Advanced menus. 1. Open Computer Setup by turning on or restarting the computer. Press f10 while the F10 = Based Setup message is displayed in the lower-left corner of the screen. ❏ To change the language, press f2. ❏ To view navigation information, press f1. ❏ To return to the Computer Setup menu, press esc. 2. Select the File, Security, Tools, or Advanced menu. 3.
Troubleshooting 4. To confirm the restoration, press f10. 5. Select File > Save changes and exit, and then follow the instructions on the screen. When the computer restarts, the factory settings are restored, and any identification information you have entered is saved. Selecting from the File Menu Table 2-1 File Menu Select To Do This System Information ■ View identification information about the computer and any battery packs in the system.
Troubleshooting Selecting from the Security Menu Table 2-2 Security Menu Select To Do This Administrator password Enter, change, or delete an HP Administrator password. Power-on password Enter, change, or delete a power-on password. Password options ■ Enable/Disable stringent security. ■ Enable/Disable required password on restart. DriveLock passwords Enable/disable DriveLock; change a DriveLock user or master password.
Troubleshooting Selecting from the Tools Menu Table 2-3 Tools Menu Select To Do This HDD Self Test options Run a quick or comprehensive self-test on any hard drive in the system. Battery Information View information about any battery packs in the computer. Memory Check ■ Run a self-test on memory modules in the computer. ■ View information about memory modules installed in the computer.
Troubleshooting Selecting from the Advanced Menu Table 2-4 Advanced Menu Select To Do This Language (or press f2) Change the Computer Setup language. Boot options ■ Enable/Disable MultiBoot, which sets a startup sequence that can include most bootable devices and media in the system. ■ Set the boot order. Device options ■ Swap the functions of the fn key and left ctrl key. ■ Enable/Disable multiple pointing devices at startup.
Troubleshooting 2.2 Troubleshooting Flowcharts Table 2-5 Troubleshooting Flowcharts Overview Flowchart Description 2.1 “Flowchart 2.1—Initial Troubleshooting” 2.2 “Flowchart 2.2—No Power, Part 1” 2.3 “Flowchart 2.3—No Power, Part 2” 2.4 “Flowchart 2.4—No Power, Part 3” 2.5 “Flowchart 2.5—No Power, Part 4” 2.6 “Flowchart 2.6—No Video, Part 1” 2.7 “Flowchart 2.7—No Video, Part 2” 2.8 “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)” 2.9 “Flowchart 2.
Troubleshooting Table 2-5 Troubleshooting Flowcharts Overview (Continued) Flowchart Description 2.14 “Flowchart 2.14—No OS Loading, Optical Drive” 2.15 “Flowchart 2.15—No Audio, Part 1” 2.16 “Flowchart 2.16—No Audio, Part 2” 2.17 “Flowchart 2.17—Nonfunctioning Device” 2.18 “Flowchart 2.18—Nonfunctioning Keyboard” 2.19 “Flowchart 2.19—Nonfunctioning Pointing Device” 2.20 “Flowchart 2.
Troubleshooting Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. N Go to Is there power? “Flowchart 2.2—No Power, Part 1.” Y N Check LED board, speaker connections. Beeps, LEDs, or error messages? N Y Go to All drives working? N Go to Is there video? (no boot) Y “Flowchart 2.6—No Video, Part 1.” N Keyboard/ pointing device working? Y N Go to Is the OS loading? N Go to Is there sound? Y “Flowchart 2.9—No Operating System (OS) Loading.” Y “Flowchart 2.15—No Audio, Part 1.
Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from docking device (if applicable). N N Power up on battery power? Go to Power up on battery power? Reset power.* “Flowchart 2.3—No Power, Part 2.” Y Y N N Power up on AC power? Power up on AC power? Reset power.* Y Go to “Flowchart 2.4—No Power, Part 3.” Y Y Power up in docking device? Done N 1. Reseat the power cables in the docking device and at the AC outlet. 2. Ensure the AC power source is active.
Troubleshooting Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Y Power on? Done N Check battery by recharging it, moving it to another computer, or replacing it. N Replace power supply (if applicable). Power on? Y N Go to Done Power on? “Flowchart 2.4—No Power, Part 3.
Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Y Power LED on? Done N Reseat AC adapter in computer and at power source. Y Done Power on? N External N Try different outlet. Power outlet active? Y Internal or external AC adapter? Replace external AC adapter. N Internal Go to “Flowchart 2.5—No Power, Part 4.” Replace power cord.
Troubleshooting Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open computer. Y Loose or damaged parts? N Reseat loose components and boards and replace damaged items. Close computer and retest. N Power on? Y Done Replace the following items (if applicable). Check computer operation after each replacement: 1. Internal DC-DC converter* 2. Internal AC adapter 3. Processor board* 4.
Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Docking Device Go to Stand-alone or docking device? *NOTE: To change from internal to external display, use the hotkey. “Flowchart 2.7—No Video, Part 2.” Stand-alone Internal or external display?* Y Adjust brightness. A Adjust brightness. Press lid switch to ensure operation. Y Video OK? Done N Internal External Video OK? Y Done N Video OK? Done N Replace the following one at a time. Test after each replacement. 1.
Troubleshooting Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove computer from docking device, if connected. Adjust display brightness. Check brightness of external monitor. N Y Go to “A” in “Flowchart 2.6—No Video, Part 1.” Video OK? Y Video OK? Done N Check that computer is properly seated in docking device, for bent pins on cable, and for monitor connection. Try another external monitor.
Troubleshooting Flowchart 2.8—Nonfunctioning Docking Device (if applicable) Nonfunctioning docking device. Reseat power cord in docking device and power outlet. Check voltage setting on docking device. Reinstall computer into docking device. Y Reset monitor cable connector at docking device. Docking device operating? N Y Docking device operating? N Done Done Test replacement docking device with new computer. Remove computer, replace docking device.
Troubleshooting Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reseat power cord in docking device and power outlet. No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” No OS loading from diskette drive, go to “Flowchart 2.13—No OS Loading, Diskette Drive.” No OS loading from optical drive, go to “Flowchart 2.14—No OS Loading, Optical Drive.” No OS loading from network, go to “Flowchart 2.20—No Network/Modem Connection.
Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Y Nonsystem disk message? N Go to “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” Reseat external hard drive. Y OS loading? Done N N Boot from CD? N Y Boot from diskette? Check the setup utility for correct booting order. Y Change boot priority through the setup utility and reboot. N Boot from hard drive? N Y Boot from hard drive? Done Y 2–18 Go to “Flowchart 2.
Troubleshooting Flowchart 2.11—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” Reseat hard drive. N 1. Replace hard drive. 2. Replace system board. Disc or diskette in drive? Y Y Hard drive accessible? Done N Remove disc or diskette and reboot. Run FDISK. Y Boot from hard drive? N Done N Hard drive partitioned? Y N Y N Go to “Flowchart 2.13—No OS Loading, Diskette Drive.
Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” N System files on hard drive? Install OS and reboot. Y Y Y Virus on hard drive? OS loading from hard drive? Clean virus. N Done N Y Run SCANDISK and check for bad sectors. Diagnostics on disc or diskette? Replace hard drive. N N Can bad sectors be fixed? Run diagnostics and follow recommendations. Replace hard drive. Y N Boot from hard drive? Fix bad sectors.
Troubleshooting Flowchart 2.13—No OS Loading, Diskette Drive Y OS not loading from diskette drive. Reseat diskette drive. OS loading? Done N Y N Bootable diskette in drive? Nonsystem disk message? N Y N Check diskette for system files. Try different diskette. Go to Boot from another device? “Flowchart 2.17—Nonfunctioning Device.” Y Y N Diskette drive enabled in the Setup utility? Enable drive and cold boot computer.
Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive Y No OS loading from CD-ROM or DVD-ROM drive. N Install bootable disc and reboot computer. Bootable disc in drive? Disc in drive? Y N Install bootable disc. Try another bootable disc. Y Boots from CD or DVD? Done N Y Boots from CD or DVD? Reseat drive. Done N N Booting from another device? Y Y Booting order correct? N Go to “Flowchart 2.17—Nonfunctioning Device.” Reset the computer. Refer to Go to Section 1.
Troubleshooting Flowchart 2.15—No Audio, Part 1 Y Turn up audio internally or externally. No audio. Audio? Done N Y Computer in docking device (if applicable)? N Go to Internal audio? Undock N “Flowchart 2.16—No Audio, Part 2.” Y Go to Test replacement docking device with new computer “Flowchart 2.16—No Audio, Part 2.” Y Go to “Flowchart 2.17—Nonfunctioning Device.
Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” N Audio driver in OS configured? Reload audio drivers. Y N Correct drivers for program? Load drivers and set configuration in OS. Y Connect to external speaker. N Audio? Y Replace audio board and speaker connections in computer (if applicable). Y Audio? Done N Replace the following components individually, retesting after each replacement: ■ Internal speakers. ■ Audio board (if applicable).
Troubleshooting Flowchart 2.17—Nonfunctioning Device Nonfunctioning device. Reseat device. Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins or other damage. Y Clear CMOS. Fix or replace broken item. Any physical device detected? N Go to Reattach device. Close computer, plug in power, and reboot. “Flowchart 2.9—No Operating System (OS) Loading.” Replace hard drive. N Device boots properly? N Replace NIC.
Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect computer to good external keyboard. N External device works? Replace system board. Y Reseat internal keyboard connector (if applicable). N Keyboard operating properly? Replace internal keyboard or cable. Y Y Keyboard operating properly? Done Done N Replace system board.
Troubleshooting Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect computer to good external pointing device. N Replace system board. External device works? Y Reseat internal pointing device connector (if applicable). N Replace internal pointing device or cable. Pointing device operating properly? Y Y Pointing device operating properly? Done Done N Replace system board.
Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. N Replace jack or have jack activated. Network or modem jack active? Y Y Connect to nondigital line. Digital line? N Y N NIC/modem configured in OS? Network or modem connection working? Reload drivers and reconfigure. Done N Y Disconnect all power from the computer and open. Replace NIC/modem (if applicable). Reseat NIC/modem (if applicable).
3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components Spare Part Number Item Description 1 Display assemblies (include wireless antenna transceivers and cables) 14.0-inch, WXGA, SVA with BrightView 14.0-inch, WXGA 412339-001 412337-001 to Section 3.3, “Display Assembly Components,” for ✎ Refer display assembly internal component spare part number information.
Illustrated Parts Catalog Computer Major Components 3–4 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description 7 Processors (include thermal pad) Intel Core Duo T2500 (2.00-GHz) Intel Core Duo T2400 (1.83-GHz) Intel Core Duo T2300 (1.66-GHz) 412333-001 412334-001 412335-001 Intel Core Solo T1300 (1.
Illustrated Parts Catalog Computer Major Components 3–6 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 17 Hard drives (include frame and connector) 5400-rpm, 100-GB 5400-rpm, 80-GB 5400-rpm, 60-GB 5400-rpm, 40-GB 18 412367-001 412366-001 412365-001 412364-001 Mini Card modules 802.11a/b/g WLAN module for use in the countries listed below. These countries are categorized as most of the world (MOW 1).
Illustrated Parts Catalog Computer Major Components 3–8 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 18 Mini Card modules (Continued) 802.11a/b/g WLAN module for use in the countries listed below. These countries are categorized as most of the world (MOW 2).
Illustrated Parts Catalog Computer Major Components 3–10 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description 19 Memory modules, 1-DIMM, DDR2 PC2-4200, 533-MHz 1024 MB 512 MB 256 MB Spare Part Number 412360-001 412359-001 412358-001 Secure Digital (SD) Memory Card (not illustrated) 512-MB 256-MB 20 407316-001 403573-001 Optical drives (include bezel) 24X Max DVD/CD-RW Combo Drive 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe 8X Max
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-2 Display Assembly Components Spare Part Number Information Item Description Spare Part Number 1 Display bezel 412344-001 2 Display hinge covers 412357-001 3 Display hinges 412356-001 4 Display panels 14.0-inch, WXGA, SVA with BrightView 14.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-3 Mass Storage Devices Spare Part Number Information Item Description 1 Hard drives (include frame and connector) 5400-rpm 100-GB 80-GB 60-GB 40-GB 2 Spare Part Number 412367-001 412366-001 412365-001 412364-001 Optical drives 24X Max DVD/CD-RW Combo Drive 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe and “HLDS” USB digital dri
Illustrated Parts Catalog 3.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-5 Spare Parts: Miscellaneous (not illustrated) (Continued) Spare Part Number Description Power cords For use in: Australia and New Zealand 394279-011 Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden 394279-021 Brazil 394279-201 Canada, French Canada, Latin America, Thailand, and the United States 394279-001 Denmark 394279-081 Hong Kong and the United Kingdom 394279-031 India 394279-D61 Israel 394279-BB1
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 394279-AA1 Power cord for use in the People’s Republic of China 394279-AB1 Power cord for use in Taiwan 394279-AD1 Power cord for use in Korea 394279-BB1 Power cord for use in Israel 394279-D61 Power cord for use in India 394362-001 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe 394370-001 Logo Kit 394371-001 Switch cover for use on models with wire
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 407674-001 802.11a/b/g WLAN Mini Card module for use in the MOW 1 countries listed below. Antigua & Barbuda Argentina Australia Bahamas Barbados Brunei Canada Chile Dominican Republic Guam Guatemala 407674-002 802.11a/b/g WLAN Mini Card module for use in the MOW 2 countries listed below.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 407674-004 802.11b/g WLAN Mini Card module GL 412240-001 945GM system board 412331-001 ExpressCard assembly 412332-001 Intel Core Solo T1300 (1.66-GHz) processor (includes thermal pad) 412333-001 Intel Core Duo T2500 (2.00-GHz) processor (includes thermal pad) 412334-001 Intel Core Duo T2400 (1.83-GHz) processor (includes thermal pad) 412335-001 Intel Core Duo T2300 (1.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 412358-001 1-DIMM, DDR2, PC2-4200, 533-MHz, 256-MB memory module 412359-001 1-DIMM, DDR2, PC2-4200, 533-MHz, 512-MB memory module 412360-001 1-DIMM, DDR2, PC2-4200, 533-MHz, 1024-MB memory module 412364-001 5400-rpm, 40-GB hard drive (includes frame and connector) 412365-001 5400-rpm, 60-GB hard drive (includes frame and connector) 412366-001 5400-rpm, 80-GB hard drive (inc
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 412397-001 Fan/heat sink assembly (includes thermal pad) 412398-001 USB/S-Video board 412400-001 LED board (includes cable) 412579-001 Rubber Feet Kit (includes computer feet used on base enclosure and display bezel rubber screw covers) 412766-001 Bluetooth module (includes Bluetooth module cable) 417370-001 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScrib
4 Removal and Replacement Preliminaries This chapter provides essential information for proper and safe removal and replacement service. 4.1 Tools Required You will need the following tools to complete the removal and replacement procedures: ■ Magnetic screwdriver ■ Phillips P0 and P1 screwdrivers ■ Flat-bladed screwdriver ■ Tool kit—includes connector removal tool, loopback plugs, and case utility tool 4.
Removal and Replacement Preliminaries Plastic Parts Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions. Cables and Connectors Ä CAUTION: When servicing the computer, ensure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer.
Removal and Replacement Preliminaries 4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a removable drive, or loss of information, observe the following precautions: ■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.
Removal and Replacement Preliminaries 4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging. ■ Keep electrostatic-sensitive parts in their containers until the parts arrive at static-free workstations.
Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material (refer to Table 4-2, “Static-Shielding Materials”). ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■ Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
Removal and Replacement Preliminaries 4.7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
5 Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are as many as 84 screws, in 8 different sizes, that must be removed, replaced, or loosened, when servicing the computer. Make special note of each screw size and location during removal and replacement. Refer to Appendix C, “Screw Listing,” for detailed information on screw sizes, locations, and usage.
Removal and Replacement Procedures 5.1 Serial Number Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.
Removal and Replacement Procedures 5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing computer components. Disassembly Sequence Chart Section Description 5.3 Preparing the Computer for Disassembly # of Screws Removed Battery pack 0 5.4 Hard Drive 2 loosened to remove the hard drive cover 4 removed to disassemble the hard drive 5.5 Computer Feet 0 5.6 Memory Module 2 loosened to remove the memory module compartment cover 5.
Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description # of Screws Removed 5.11 Display Assembly Display bezel Display release hooks Display inverter Display hinge covers Display panel Display hinges Wireless antenna transceivers 4 6 4 1 4 2 4 4 5.12 Base Enclosure 18 5.13 USB/S-Video Board 2 5.14 Bluetooth Module 2 5.15 Speaker Assembly 0 5.16 RTC Battery 0 5.17 Fan/Heat Sink Assembly 4 loosened 5.18 Processor 1 loosened 5.
Removal and Replacement Procedures Battery Pack Spare Part Number Information 12-cell, 8.8-AHr 6-cell, 4.0-AHr 396600-001 396601-001 4. Remove the battery pack by following these steps: a. Turn the computer upside down with the front panel toward you. b. Slide and hold the battery release latch 1 to the left. (The front edge of the battery pack disengages from the computer.) c. Lift the front edge of the battery pack 2 up and swing it back. d. Remove the battery pack.
Removal and Replacement Procedures 5.4 Hard Drive Hard Drive Spare Part Number Information Frame and connector included. 5400-rpm, 100-GB 5400-rpm, 80-GB 5400-rpm, 60-GB 5400-rpm, 40-GB 412367-001 412366-001 412365-001 412364-001 1. Prepare the computer for disassembly (refer to Section 5.3).
Removal and Replacement Procedures 2. Loosen the two black Phillips PM2.0×5.0 screws 1 that secure the hard drive cover to the computer. 3. Lift the left side of the cover 2 and swing it to the right. 4. Remove the hard drive cover. hard drive cover is included in the Plastics Kit, spare part ✎ The number 412385-001.
Removal and Replacement Procedures 5. Use the mylar tab 1 to lift the hard drive 2 until it disconnects from the computer. 6. Remove the hard drive from the hard drive bay.
Removal and Replacement Procedures 7. Remove the four Phillips PM2.5×4.0 screws 1 that secure the hard drive frame to the hard drive. 8. Lift the frame 2 straight up to remove if from the hard drive. 9. Slide the hard drive connector 3 off the hard drive. Removing the Hard Drive Frame and Connector Reverse the above procedure to install and reassemble the hard drive.
Removal and Replacement Procedures 5.5 Computer Feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part number 412579-001. Replacing the Computer Feet 5.
Removal and Replacement Procedures 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Loosen the two black Phillips PM2.0×5.0 screws 1 that secure the memory module compartment cover to the computer. 3. Lift the front edge of the memory module compartment cover 2 up and swing it back. 4. Remove the memory module compartment cover. memory module compartment cover is included in the ✎ The Plastics Kit, spare part number 412385-001.
Removal and Replacement Procedures 5. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the memory module opposite the memory module socket rises away from the computer.) 6. Slide the module 2 away from the socket at an angle. modules are designed with a notch 3 to prevent ✎ Memory incorrect installation into the memory module socket. Removing the Memory Module Reverse the above procedure to install a memory module.
Removal and Replacement Procedures 5.7 Mini Card Module Mini Card Module Spare Part Number Information 802.11a/b/g WLAN module for use in the MOW 1 countries listed below. Antigua & Barbuda Argentina Australia Bahamas Barbados Brunei Canada Chile Dominican Republic Guam Guatemala Hong Kong Panama India Indonesia Malaysia Mexico New Zealand 802.11a/b/g WLAN module for use in the MOW 2 countries listed below.
Removal and Replacement Procedures Mini Card Module Spare Part Number Information (Continued) 802.11a/b/g WLAN module for use in the ROW countries listed below. China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea 407674-003 Uruguay Venezuela 802.11b/g WLAN module HS MOW 407159-001 802.11b/g WLAN module HS ROW 407159-002 802.11b/g WLAN module GL 407674-004 1. Prepare the computer for disassembly (Section 5.3).
Removal and Replacement Procedures 2. Loosen the black Phillips PM2.0×5.0 screw 1 that secures the Mini Card compartment cover to the computer. 3. Lift the rear edge of the Mini Card compartment cover 2 up, and then swing it forward. 4. Remove the Mini Card compartment cover. Mini Card compartment cover is included in the Plastics ✎ The Kit, spare part number 412385-001.
Removal and Replacement Procedures 5. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card module before disconnecting the cables, then disconnect the cables 1 from the module. 6. Remove the two black Phillips PM2.0×5.0 screws 2 that secure the Mini Card module to the system board. (The edge of the module opposite the Mini Card socket rises away from the computer). 7. Remove the Mini Card module 3 by pulling the module away from the socket at an angle.
Removal and Replacement Procedures 5.8 Optical Drive Optical Drive Spare Part Number Information 24X Max DVD/CD-RW Combo Drive 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe 8X Max DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe and “HLDS” 412369-001 412371-001 394362-001 417370-001 1. Prepare the computer for disassembly (Section 5.3).
Removal and Replacement Procedures 2. Remove the Phillips PM2.0×8.5 screw 1 that secures the optical drive to the computer. 3. Insert a thin tool, such as a paper clip, into the media tray release hole 2. (The optical drive media tray releases from the optical drive.) 4. Use the media tray frame to slide the optical drive 3 to the left. 5. Remove the optical drive.
Removal and Replacement Procedures 6. Remove the two Phillips PM2.0×2.0 screws 1 that secure the optical drive bracket to the optical drive. 7. Remove the optical drive bracket 2. Removing the Optical Drive Bracket Reverse the above procedure to reassemble and install the optical drive.
Removal and Replacement Procedures 5.9 Switch Cover Switch Cover Spare Part Number Information For use on models with wireless capability For use on models without wireless capability 394371-001 394372-001 1. Prepare the computer for disassembly (Section 5.3).
Removal and Replacement Procedures 2. Position the computer with the rear panel toward you. 3. Remove the two silver Phillips PM2.0×5.0 screws that secure the switch cover to the computer.
Removal and Replacement Procedures 4. Turn the computer display side up with the front panel toward you. 5. Open the computer as far as possible. 6. Insert a flat-bladed screwdriver into the slots located behind the f1, f5, f11, and insert keys 1 and lift up on the front edge of the switch cover 2 until it disengages from the computer. 7. Remove the switch cover. Removing the Switch Cover Reverse the above procedure to install the switch cover.
Removal and Replacement Procedures 5.10 Keyboard Keyboard Spare Part Number Information French Canada International Korea Latin America Taiwan Thailand 394277-121 394277-B31 394277-AD1 394277-161 394277-AB1 394277-281 Asia Pacific, Australia, Canada, Hong Kong, the People’s Republic of China, and the United States 394277-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the optical drive (Section 5.8). 3. Remove the switch cover (Section 5.9). 4. Close the computer. 5.
Removal and Replacement Procedures 6. Remove the four Phillips PM2.0×3.0 screws 1 that secure the keyboard to the computer. 7. Swing the rear edge of the keyboard 2 up and forward until it rests on the palm rest.
Removal and Replacement Procedures 8. Release the ZIF connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board. Disconnecting the Keyboard Cable 9. Remove the keyboard. Reverse the above procedure to install the keyboard.
Removal and Replacement Procedures 5.11 Display Assembly Display Assembly Spare Part Number Information 14.0-inch, WXGA, SVA with Brightview 14.0-inch, WXGA 412339-001 412337-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the memory module compartment cover (Section 5.6). 3. Remove the Mini Card compartment cover and disconnect the wireless antenna cables from the Mini Card (Section 5.7). 4. Remove the wireless antenna cables from the Mini Card and memory module compartments. 5.
Removal and Replacement Procedures 9. Disconnect the display cable 1 from the system board. 10. Remove the tape 2 that secures the wireless antenna cables to the top cover. 11. Remove the cables from the clips 3 in the top cover.
Removal and Replacement Procedures Ä CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components. 12. Remove the four black Phillips PM2.0×5.0 screws 1 that secure the display assembly to the computer. 13. Remove the display assembly 2.
Removal and Replacement Procedures 14. Remove the six rubber screw covers 1 and the six Phillips PM2.5×6.0 screws 2 that secure the display bezel to the display assembly. rubber screw covers are included in the Rubber Feet Kit, ✎ The spare part number 412579-001.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display bezel 412344-001 Display enclosure (includes wireless antenna transceivers and cables and microphone and cable) 412351-001 15. Flex the insides edges of the left and right sides 1 and the top and bottom sides 2 of the display bezel until the bezel disengages from the display enclosure. 16. Remove the display bezel 3.
Removal and Replacement Procedures display release hooks are available in the Display Hinge ✎ The Kit, spare part number 412356-001. 17. If it is necessary to replace the display release hooks, remove the two Phillips PM2.5×6.0 screws 1 that secure each hook to the display enclosure. 18. Remove the display release hooks 2.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display inverter 412346-001 19. Remove the Phillips PM2.0×3.0 screw 1 that secures the display inverter to the display enclosure. 20. Lift the inverter 2 out of the enclosure as far as the display cable and backlight cables will allow. 21. Disconnect the display 3 and backlight cables 4 from the inverter. 22. Remove the display inverter.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display hinge covers 412357-001 23. If it is necessary to replace the display hinge covers, remove the two Phillips PM2.5×6.0 screws 1 that secure each cover to the display enclosure. 24. Remove the display hinge covers 2.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Spare Part Number Display panels 14.0-inch, WXGA, SVA with BrightView 14.0-inch, WXGA 412341-001 412340-001 25. Remove the two Phillips PM2.5×6.0 screws 1 that secure the display panel to the display enclosure. 26. Remove the display panel 2 from the display enclosure.
Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Display Hinge Kit, includes: Display hinges Display release hooks Spare Part Number 412356-001 27. If it is necessary to replace the display hinges, remove the two Phillips PM2.0×3.0 screws 1 that secure each hinge to the display panel. 28. Remove the display hinges 2.
Removal and Replacement Procedures wireless antenna transceivers and cables are included with ✎ The the display enclosure, spare part number 412351-001. 29. If it is necessary to replace the wireless transceivers and cables, remove the two Phillips PM2.0×3.0 screws 1 that secure the left and right transceivers to the display enclosure. 30. Release the retention tabs 2 built in to the display enclosure lining that secure the wireless antenna cables to the display enclosure. 31.
Removal and Replacement Procedures 5.12 Base Enclosure Base Enclosure Spare Part Number Information Base enclosure 412383-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.
Removal and Replacement Procedures 2. Remove the fifteen Phillips PM2.0×8.5 screws that secure the base enclosure to the computer.
Removal and Replacement Procedures 3. Remove the three silver Phillips PM2.0×5.0 screws that secure the base enclosure to the computer. 4. Lift the base enclosure straight up and remove it. Removing the Base Enclosure Reverse the above procedure to install the base enclosure.
Removal and Replacement Procedures 5.13 USB/S-Video Board USB/S-Video Board Spare Part Number Information USB/S-Video Board 412398-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosure (Section 5.
Removal and Replacement Procedures 2. Remove the two silver Phillips PM2.0×5.0 screws 1 that secure the USB/S-Video board to the top cover. 3. Lift up on the right side of the board 2 to disconnect it from the system board. 4. Remove the USB/S-Video board. Removing the USB/S-Video Board Reverse the above procedure to install the USB/S-Video board.
Removal and Replacement Procedures 5.14 Bluetooth Module Bluetooth Module Spare Part Number Information Bluetooth module 412766-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosure (Section 5.12) ❏ USB/S-Video board (Section 5.
Removal and Replacement Procedures 2. Turn the USB/S-Video board upside down with the USB port facing you. 3. Remove the two PM1.5×3.5 screws 1 that secure the Bluetooth module to the USB/S-Video board. 4. Disconnect the Bluetooth module cable 2 from the USB/S-Video board. 5. Remove the Bluetooth module 3. Removing the Bluetooth Module Reverse the above procedure to install the Bluetooth module.
Removal and Replacement Procedures 5.15 Speaker Assembly Speaker Assembly Spare Part Number Information Speaker assembly 394373-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosure (Section 5.
Removal and Replacement Procedures 2. Disconnect the speaker cable 1 from the system board. 3. Lift the speaker 2 straight up to remove it from the top cover. Removing the Speaker Assembly Reverse the above procedure to install the speaker assembly.
Removal and Replacement Procedures 5.16 RTC Battery RTC Battery Spare Part Number Information RTC battery 412390-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosure (Section 5.
Removal and Replacement Procedures 2. Remove the RTC battery from the socket on the system board. Removing the RTC Battery Reverse the above procedure to install the RTC battery. Be sure that the RTC battery is installed with the “+” sign facing up.
Removal and Replacement Procedures 5.17 Fan/Heat Sink Assembly Fan/Heat Sink Assembly Spare Part Number Information Fan/heat sink assembly (includes thermal pad) 412397-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosure (Section 5.12) 2. Turn the computer upside down with the front toward you.
Removal and Replacement Procedures 3. Disconnect the fan cable 1 from the system board. 4. Loosen the four Phillips PM2.5×5.0 screws 2 that secure the fan/heat sink assembly to the top cover. 5. Remove the fan/heat sink assembly 3. Removing the Fan/Heat Sink Assembly Reverse the above procedure to install the fan/heat sink assembly.
Removal and Replacement Procedures 5.18 Processor Processor Spare Part Number Information Intel Core Duo T2500 (2.00-GHz) Intel Core Duo T2400 (1.83-GHz) Intel Core Duo T2300 (1.66-GHz) 412333-001 412334-001 412335-001 Intel Core Solo T1300 (1.66-GHz) 412332-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosure (Section 5.
Removal and Replacement Procedures 2. Turn the processor locking screw 1 one-half turn counterclockwise until you feel a click. 3. Lift the processor 2 straight up and remove it. gold triangle 3 on the processor should be aligned in the ✎ The front right corner when you install the processor. Removing the Processor Reverse the above procedure to install a processor.
Removal and Replacement Procedures 5.19 System Board System Board Spare Part Number Information 945GM 412240-001 replacing the system board, ensure that the following ✎ When components are removed from the defective system board and installed on the replacement system board: ■ Memory modules (Section 5.6) ■ Mini Card module (Section 5.7) ■ RTC battery (Section 5.16) ■ Fan/heat sink assembly (Section 5.17) ■ Processor (Section 5.
Removal and Replacement Procedures 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosoure (Section 5.12) ❏ USB/S-Video board (Section 5.13) ❏ Speaker assembly (Section 5.15) 2. Turn the top cover right side up with the front toward you. 3.
Removal and Replacement Procedures 4. Turn the top cover upside down with the front toward you. 5. Release the ZIF connector 1 to which the LED board cable is connected and disconnect the cable 2 from the system board. 6. Remove the three silver Phillips PM2.0×5.0 screws 3 that secure the system board to the top cover.
Removal and Replacement Procedures 7. Flex and hold the left side of the top cover 1. 8. Lift the left side of the system board 2 until the USB 3 and 1394 connectors 4 clear the top cover.
Removal and Replacement Procedures 9. Flex and hold the front edge of the top cover 1. 10. Lift the system board 2 until the audio connectors 3 clear the top cover.
Removal and Replacement Procedures 11. Slide the system board to the left at an angle and remove it from the top cover. Removing the System Board Reverse the above procedure to install the system board.
Removal and Replacement Procedures 5.20 LED Board LED Board Spare Part Number Information LED board 412400-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosoure (Section 5.12) ❏ USB/S-Video board (Section 5.13) ❏ Speaker assembly (Section 5.15) ❏ System board (Section 5.19) 2.
Removal and Replacement Procedures 3. Release the ZIF connector 1 to which the LED board cable is connected and disconnect the cable 2 from the system board. 4. Remove the two Phillips PM2.0×3.0 screws 3 that secure the LED board to the top cover. Removing the LED Board Screws 5. Remove the LED board. Reverse the above procedure to install the LED board.
Removal and Replacement Procedures 5.21 ExpressCard Assembly ExpressCard Assembly Spare Part Number Information ExpressCard assembly 412331-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Optical drive (Section 5.8) ❏ Switch cover (Section 5.9) ❏ Keyboard (Section 5.10) ❏ Display assembly (Section 5.11) ❏ Base enclosoure (Section 5.12) ❏ USB/S-Video board (Section 5.13) ❏ Speaker assembly (Section 5.15) ❏ System board (Section 5.19) 2.
Removal and Replacement Procedures 3. Remove the two Phillips PM2.0×2.0 screws that secure the ExpressCard assembly to the system board.
Removal and Replacement Procedures 4. Turn the system board right side up with the ExpressCard eject button toward you. 5. Lift the back of the ExpressCard assembly to disconnect it from the system board. Removing the ExpressCard Assembly Reverse the above procedure to install the ExpressCard assembly.
6 Specifications This chapter provides physical and performance specifications. Table 6-1 Computer Dimensions Height (varies from front to back) Width Depth Weight (varies by configuration) 3.29 cm to 3.89 cm 23.06 cm 33.40 cm 1.30 in to 1.53 in 9.08 in 13.15 in 2.39 kg 5.26 lb Stand-alone power requirements Operating voltage Operating current Peak operating power 18.5 V dc to 19.0 V dc 3.5 A or 4.
Specifications Table 6-1 Computer (Continued) Shock Operating Nonoperating 125 g, 2 ms, half-sine 200 g, 2 ms, half-sine Random Vibration Operating Nonoperating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate product safety standards specify thermal limits for plastic ✎ Applicable surfaces. The computer operates well within this range of temperatures.
Specifications Table 6-2 14.0-inch, WXGA, SVA Display Dimensions Height Width Diagonal 27.94 cm 20.83 cm 35.56 cm Number of colors Up to 16.8 million Contrast ratio 250:1 Brightness 180 nits typical 11.0 in 8.2 in 14.0 in Pixel resolution Pitch Format Configuration 0.279 × 0.
Specifications Table 6-3 Hard Drives 80-GB 60-GB 60-GB 40-GB Dimensions Height Width Weight Interface type 9.5 mm 70 mm 99 g 9.5 mm 70 mm 102 g 9.5 mm 70 mm 99 g 9.
Specifications Table 6-4 Primary 6-cell, Li-Ion Battery Pack Dimensions Height Width Depth Weight 2.00 cm 9.40 cm 13.40 cm 0.34 kg 0.79 in 3.70 in 5.28 in 0.75 lb Energy Voltage Amp-hour capacity Watt-hour capacity 11.1 V 4.
Specifications Table 6-5 DVD/CD-RW Combo Drive Applicable disc Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc 6–6 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-5 DVD/CD-RW Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD media DVD media < 110 ms < 210 ms < 130 ms < 225 ms Random Full stroke Audio output level Line-out, 0.7 V rms Cache buffer 2 MB Data transfer rate CD-R (24X) CD-RW (10X) CD-ROM (24X) DVD (8X) Multiword DMA mode 2 3600 KB/s (150 KB/s at 1X CD rate) 1500 KB/s (150 KB/s at 1X CD rate) 3600 KB/s (150 KB/s at 1X CD rate) 10,800 KB/s (1352 KB/s at 1X DVD rate) 16.
Specifications Table 6-6 DVD±RW/R and CD-RW Double-Layer Combo Drive Applicable disc Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-R and DVD-RW DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc 6–8 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-6 DVD±RW/R and CD-RW Double-Layer Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD media DVD media < 175 ms < 285 ms < 230 ms < 335 ms Random Full stroke Audio output level Audio-out, 0.
Specifications Table 6-7 System DMA Hardware DMA System Function DMA0 Not applicable DMA1 Not applicable DMA2 Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5 Available for ExpressCard DMA6 Not assigned DMA7 Not assigned 6–10 Maintenance and Service Guide
Specifications Table 6-8 System Interrupts Hardware IRQ System Function IRQ0 System timer IRQ1 Quick Launch buttons IRQ2 Cascaded IRQ3 USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9* Microsoft ACPI-compliant system IRQ10* USB UHCI controller—24C2 GM/GME Graphic Controller Realtek RTL8139 Family PCI fast Ethernet Controller IRQ11
Specifications Table 6-8 System Interrupts (Continued) Hardware IRQ System Function IRQ12 Synaptics PS/2 port pointing device IRQ13 Numeric data processor IRQ14 Primary IDE channel IRQ15 Secondary IDE channel IRQ17 Conexant AC -Link Audio IRQ17 Soft V90 Data Fax Modem with SmartCP IRQ17 ATi Mobility Radeon Xpress 200 Series IRQ19 Standard Enhanced PCI to USB Host Controller IRQ19 Standard OpenHCD USB Host Controller IRQ19 Standard OpenHCD USB Host Controller IRQ20 TI 6411 PCIxx21/x51
Specifications Table 6-9 System I/O Addresses I/O Address (hex) System Function (shipping configuration) 0x00000000-0x00000CF7 PCI bus 0x00000000-0x00000CF7 Direct memory access controller 0x00000020-0x00000021 Programmable interrupt controller 0x0000002E-0x0000002F System board resources 0x00000040-0x00000043 System timer 0x00000060-0x00000060 Quick Launch Buttons 0x00000061-0x00000061 System speaker 0x00000062-0x00000062 Microsoft ACPI-Compliant Embedded Controller 0x00000064-0x00000064
Specifications Table 6-9 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0x000001F0-0x000001F7 Primary IDE Channel 0x00000220-0x0000022F System board resources 0x00000274-0x00000277 ISAPNP Read Data Port 0x00000279-0x00000279 ISAPNP Read Data Port 0x00000280-0x00000293 System board resources 0x00000376-0x00000376 Secondary IDE Channel 0x000003B0-0x000003BB PCI standard PCI-to-PCI bridge 0x000003B0-0x000003BB ATI MOBILITY RADEON Xpress 200 Series
Specifications Table 6-9 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0x00000C6F-0x00000C6F System board resources 0x00000CD4-0x00000CD5 System board resources 0x00000CD6-0x00000CD7 System board resources 0x00000CD8-0x00000CDF System board resources 0x00000D00-0x0000FFFF PCI bus 0x00000F40-0x00000F47 System board resources 0x00001080-0x00001080 System board resources 0x00008000-0x0000805F System board resources 0x00008100-0x000081FF System b
Specifications Table 6-10 System Memory Map Memory Map Address (hex) System Function (shipping configuration) 0xD4100000-0xD41FFFFF PCI standard PCI-to-PCI bridge 0xD4100000-0xD41FFFFF ATI MOBILITY RADEON Xpress 200 Series 0xD8000000-0xDBFFFFFF PCI standard PCI-to-PCI bridge 0xD8000000-0xDBFFFFFF ATI MOBILITY RADEON Xpress 200 Series 0xFAC00000-0xFEBFFFFF PCI standard PCI-to-PCI bridge 0xF6C00000-0xFABFFFFF PCI standard PCI-to-PCI bridge 0xD4000000-0xD4000FFF Standard OpenHCD USB Host Contro
Specifications Table 6-10 System Memory Map (Continued) Memory Map Address (hex) System Function (shipping configuration) 0xD4208000-0xD42087FF Texas Instruments OHCI Compliant IEEE 1394 Host Controller 0xD4200000-0xD4203FFF Texas Instruments OHCI Compliant IEEE 1394 Host Controller 0xD4204000-0xD4205FFF Broadcom 802.
Specifications Table 6-10 System Memory Map (Continued) Memory Map Address (hex) System Function (shipping configuration) 0xD4209400-0xD42094FF Realtek RTL8139/810x Family Fast Ethernet NIC 0xD4003400-0xD40034FF Conexant AC-Link Audio 0xD4003800-0xD40038FF SoftV90 Data Fax Modem with SmartCP 0xFEC00000-0xFEC00FFF System board resources 0xFEE00000-0xFEE00FFF System board resources 0xA0000-0xBFFFF PCI bus 0xA0000-0xBFFFF PCI standard PCI-to-PCI bridge 0xA0000-0xBFFFF ATI MOBILITY RADEON Xpre
A Connector Pin Assignments Table A-1 Universal Serial Bus Pin Signal Pin Signal 1 +5 VDC 3 Data + 2 Data – 4 Ground Maintenance and Service Guide A–1
Connector Pin Assignments Table A-2 RJ-45 (Network) Pin Signal Pin Signal 1 Transmit + 5 Unused 2 Transmit – 6 Receive – 3 Receive + 7 Unused 4 Unused 8 Unused A–2 Maintenance and Service Guide
Connector Pin Assignments Table A-3 S-Video-Out Pin Signal Pin Signal 1 TV-Ground 5 TV-CD 2 TV-CVBS 6 TV-Ground 3 TV-Ground 7 TV-YD 4 TV-Ground Maintenance and Service Guide A–3
Connector Pin Assignments Table A-4 External Monitor Pin Signal Pin Signal 1 Red analog 9 +5 VDC 2 Green analog 10 Ground 3 Blue analog 11 Monitor detect 4 Not connected 12 DDC 2B data 5 Ground 13 Horizontal sync 6 Ground analog 14 Vertical sync 7 Ground analog 15 DDC 2B clock 8 Ground analog A–4 Maintenance and Service Guide
Connector Pin Assignments Table A-5 RJ-11 (Modem) Pin Signal Pin Signal 1 Unused 4 Unused 2 Tip 5 Unused 3 Ring 6 Unused Maintenance and Service Guide A–5
Connector Pin Assignments Table A-6 Audio-In (Microphone) Pin Signal Pin Signal 1 Audio signal in 3 Ground 2 Audio signal in Table A-7 Audio-Out (Headphone) Pin Signal Pin Signal 1 Audio out, left channel 3 Ground 2 Audio out, right channel A–6 Maintenance and Service Guide
B Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the computer meets the requirements for use in the country where the equipment is purchased. Power cord sets for use in other countries must meet the requirements of the country where the computer is used.
Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries. B–2 ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.
Power Cord Set Requirements Country-Specific Requirements 3-Conductor Power Cord Set Requirements Country/Region Accredited Agency Applicable Note Number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 Notes: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country/Region Accredited Agency Applicable Note Number Korea EK 4 The Netherlands KEMA 1 Norway NEMKO 1 People’s Republic of China CCC 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 United Kingdom BSI 1 United States UL 2 Notes: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
C Screw Listing This appendix provides specification and reference information for the screws used in the computer. All screws listed in this appendix are available in the Screw Kit, spare part number 412387-001, and the Display Screw Kit, spare part number 417713-001.
Screw Listing Table C-1 Black Phillips PM2.0×5.0 Screw mm Color Qty. Length Thread Head Width Black 11 5.0 mm 2.0 mm 4.0 mm Where used: 1 Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C clips; documented in Section 5.3) 2 Two screws that secure the memory module compartment cover to the computer (screws are captured on the cover by C clips; documented in Section 5.
Screw Listing Table C-1 Black Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 11 5.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the Mini Card module to the computer (documented in Section 5.7) Black Phillips PM2.0×5.
Screw Listing Table C-1 Black Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 11 5.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the display assembly to the computer (documented in Section 5.11) Black Phillips PM2.0×5.
Screw Listing Table C-2 Phillips PM2.5×4.0 Screw mm Color Qty. Length Thread Head Width Silver 4 4.0 mm 2.5 mm 4.0 mm Where used: 4 screws that secure the hard drive frame to the hard drive (documented in Section 5.3) Phillips PM2.5×4.
Screw Listing Table C-3 Phillips PM2.0×8.5 Screw mm Color Qty. Length Thread Head Width Black 16 8.5 mm 2.0 mm 4.0 mm Where used: One screw that secures the optical drive to the computer (documented in Section 5.8) Phillips PM2.0×8.
Screw Listing Table C-3 Phillips PM2.0×8.5 Screw (Continued) mm Color Qty. Length Thread Head Width Black 16 8.5 mm 2.0 mm 4.0 mm Where used: 15 screws that secure the base enclosure to the computer (documented in Section 5.12) Phillips PM2.0×8.
Screw Listing Table C-4 Silver Phillips PM2.0×5.0 Screw mm Color Qty. Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the switch cover to the computer (documented in Section 5.9) Silver Phillips PM2.0×5.
Screw Listing Table C-4 Silver Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 3 screws that secure the base enclosure to the computer (documented in Section 5.12) Silver Phillips PM2.0×5.
Screw Listing Table C-4 Silver Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the USB/S-Video board to the computer (documented in Section 5.13) Silver Phillips PM2.0×5.
Screw Listing Table C-4 Silver Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the fan/heat sink assembly to the computer (documented in Section 5.17) Silver Phillips PM2.0×5.
Screw Listing Table C-4 Silver Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 14 5.0 mm 2.0 mm 4.0 mm Where used: 3 screws that secure the system board to the computer (documented in Section 5.19) Silver Phillips PM2.0×5.
Screw Listing Table C-5 Phillips PM2.0×3.0 Screw mm Color Qty. Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the keyboard to the computer (documented in Section 5.10) Phillips PM2.0×3.
Screw Listing Table C-5 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the display inverter to the display assembly (documented in Section 5.11) Phillips PM2.0×3.
Screw Listing Table C-5 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the display hinges to the display assembly (documented in Section 5.11) Phillips PM2.0×3.
Screw Listing Table C-5 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the wireless antenna transceivers to the display enclosure (documented in Section 5.20) Phillips PM2.0×3.
Screw Listing Table C-5 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 15 3.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the LED board to the computer (documented in Section 5.20) Phillips PM2.0×3.
Screw Listing Table C-6 Phillips PM1.5×3.5 Screw mm Color Qty. Length Thread Head Width Silver 2 3.5 mm 1.5 mm 3.0 mm Where used: 2 screws that secure the Bluetooth board to the USB/S-Video board (documented in Section 5.14) Phillips PM1.5×3.
Screw Listing Table C-7 Phillips PM2.0×2.0 Screw mm Color Qty. Length Thread Head Width Silver 4 2.0 mm 2.0 mm 3.0 mm Where used: 2 screws that secure the optical drive bracket to the optical drive (documented in Section 5.8) Phillips PM2.0×2.
Screw Listing Table C-7 Phillips PM2.0×2.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 4 2.0 mm 2.0 mm 3.0 mm Where used: 2 screws that secure the ExpressCard assembly to the system board (documented in Section 5.21) Phillips PM2.0×2.
Screw Listing Table C-8 Phillips PM2.5×6.0 Screw mm Color Qty. Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 6 screws that secure the display bezel to the display assembly (documented in Section 5.11) Phillips PM2.5×6.
Screw Listing Table C-8 Phillips PM2.5×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the display release hooks to the display enclosure (documented in Section 5.11) Phillips PM2.5×6.
Screw Listing Table C-8 Phillips PM2.5×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the display hinge covers to the display enclosure (documented in Section 5.11) Phillips PM2.5×6.
Screw Listing Table C-8 Phillips PM2.5×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 16 6.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display panel to the display enclosure (documented in Section 5.11) Phillips PM2.5×6.
D Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Ä CAUTION: The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling should be exercised when removing these components.
Display Component Recycling This appendix provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight 1 and the LCD panel 2. procedures differ from one display assembly to ✎ Disassembly another. The procedures provided in this appendix are general disassembly instructions. Specific details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
Display Component Recycling Perform the following steps to disassemble the display assembly: 1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
Display Component Recycling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel 3.
Display Component Recycling 4. Disconnect all LCD panel cables 1 from the display inverter board and remove the inverter board 2.
Display Component Recycling 5. Remove all screws 1 that secure the LCD panel to the display enclosure. 6. Remove the LCD panel 2 from the display enclosure.
Display Component Recycling 7. Turn the LCD panel upside down. 8. Remove all screws that secure the LCD panel frame to the LCD panel.
Display Component Recycling 9. Use a sharp-edged tool to cut the tape 1 that secures the side of the LCD panel to the LCD panel frame. 10. Remove the LCD panel frame 2 from the display panel.
Display Component Recycling 11. Remove the screws 1 that secure the backlight cover to the LCD panel. 12. Lift the top edge of the backlight cover 2 and swing it forward. 13. Remove the backlight cover.
Display Component Recycling 14. Turn the LCD panel right-side up. 15. Remove the backlight cables 1 from the clip 2 in the LCD panel.
Display Component Recycling 16. Turn the LCD panel upside down. 17. Remove the backlight frame from the LCD panel.
Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 18. Slide the backlight out of the backlight frame.
Display Component Recycling 19. Disconnect the display cable 1 from the LCD panel. 20. Remove the screws 2 that secure the LCD panel to the LCD rear panel. 21. Release the LCD panel 3 from the LCD rear panel. 22. Release the tape 4 that secures the LCD panel to the LCD rear panel.
Display Component Recycling 23. Remove the LCD panel. Removing the LCD Panel 24. Recycle the backlight and LCD panel.
Index 1394 port 1–9 A AC adapter, spare part number 3–17, 3–20 arrow keys 1–13 audio troubleshooting 2–23 audio-in (microphone) jack location 1–7 pin assignments A–6 audio-out (headphone) jack location 1–7 pin assignments A–6 B base enclosure removal 5–37 spare part number 3–5, 3–23, 5–37 battery light 1–7 battery pack location 1–18 removal 5–5 spare part numbers 3–5, 3–20 specifications 6–5 battery pack release latch 1–18 Maintenance and Service Guide Bluetooth module removal 5–42 spare part number 3–5
Index Security Menu 2–4 Tools Menu 2–5 computer specifications 6–1 connector pin assignments external monitor A–4 headphone A–6 microphone A–6 monitor A–4 RJ-11 (modem) A–5 RJ-45 (network) A–2 S-Video-out A–3 Universal Serial Bus (USB) A–1 connectors, service considerations 4–2 D design overview 1–20 disassembly sequence chart 5–3 diskette drive, OS loading problems 2–21 display assembly removal 5–26 spare part numbers 3–3, 3–22, 5–26 specifications 6–3 display bezel removal 5–30 spare part number 3–22, 5
Index DVD±RW/R and CD-RW Double-Layer Combo Drive OS loading problems 2–22 precautions 4–3 spare part number 3–11, 3–15, 3–20, 3–23, 3–24, 5–17 specifications 6–8 E electrostatic discharge 4–4, 4–8 exhaust vents 1–11, 1–19 expansion port 2 1–11 ExpressCard assembly spare part number 3–5, 3–22 ExpressCard slot 1–11 ExpressCard slot bezel, illustrated 3–16 external monitor port location 1–11 pin assignments A–4 no OS loading 2–17 no OS loading from diskette drive 2–21 no OS loading from hard drive 2–18, 2–
Index headphone jack location 1–7 pin assignments A–6 headset, spare part number 3–17, 3–19 HP backpack, spare part number 3–17, 3–20 HP Mobile Remote Control, spare part number 3–20 HP xc2000 Notebook All-in-One Media Cable, spare part number 3–17, 3–20 I I/O address specifications 6–13 interrupt specifications 6–11 K keyboard removal 5–23 spare part numbers 3–3, 3–19, 5–23 troubleshooting 2–26 keyboard components 1–12 keypad keys 1–13 L label area 1–19 LED board removal 5–58 spare part number 3–3, 3–2
Index N network jack location 1–11 pin assignments A–2 network, troubleshooting 2–28 nonfunctioning device, troubleshooting 2–16, 2–25 num lock key 1–13 num lock light 1–15 O optical drive location 1–9, 1–18 OS loading problems 2–22 precautions 4–3 removal 5–17 spare part numbers 3–11, 3–15, 5–17 P packing precautions 4–5 password clearing 1–4 plastic parts 4–2 Plastics Kit contents 3–16 spare part number 3–5, 3–16, 3–23 pointing device, troubleshooting 2–27 power button 1–15 power connector 1–11 power c
Index security cable slot 1–11 serial number 3–1, 5–2 service considerations 4–1 speaker assembly removal 5–44 spare part number 3–5, 3–20, 5–44 speakers 1–7 specifications battery pack 6–5 computer 6–1 display 6–3 DVD/CD-RW Combo Drive 6–6 DVD±RW/R and CD-RW Double-Layer Combo Drive 6–8 hard drive 6–4 I/O addresses 6–13 interrupts 6–11 system DMA 6–10 static shielding materials 4–8 S-Video-out jack location 1–9 pin assignments A–3 switch cover removal 5–20 spare part numbers 3–3, 3–20, 5–20 system board r
Index U Universal Serial Bus (USB) connector location 1–9, 1–11 pin assignments A–1 unknown password 1–4 USB camera cable, spare part number 3–22 USB digital drive, spare part number 3–15, 3–19 USB travel mouse, spare part number 3–17, 3–19 USB/S-Video board removal 5–40 spare part number 3–5, 3–24, 5–40 V video troubleshooting 2–14 volume buttons 1–15 W Windows applications key 1–13 Windows logo key 1–13 wireless antenna cable removal 5–36 wireless button 1–15 wireless button light 1–7 wireless light 1–