Operating instructions

4
W415-0680 / 04.10.08
THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes.
Installation practices vary from region to region and it is important to know the specifi cs that apply to your area,
for example: in Massachusetts State:
• The fi replace damper must be removed or welded in the open position prior to installation of a fi replace insert or gas log.
• A carbon monoxide detector is required in all rooms containing gas fi red appliances
• The appliance off valve must be a “T” handle gas cock.
• The fl exible connector must not be longer than 36".
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion
product.
• WARNING: This product must be installed by a licensed plumber or gas fi tter when installed within the commonwealth of
Massachusetts.
In absence of local codes, install the BCDV36CF(G) and BCDV42CF to the current National Fuel Gas Code, ANSI Z223.1, or the
current CAN/CGA B149, Installation Codes. Mobile home installation must conform with local codes or in the absence of local
codes, install to the current standard for gas equipped mobile housing CAN/CSA ZA240 MH Series in Canada or the Manu-
factured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the Fire Safety Criteria for Manufactured Home
Installations, Sites and Communities Standard ANSI/NFPA 501A in the United States.
The fi replace and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing
of that system at test pressures in excess of 1/2 psig (3.5 kPa). The fi replace must be isolated from the gas supply piping system
by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal
to or less than 1/2 psig (3.5 kPa).
When the fi replace is installed directly on carpeting, vinyl tile or other combustible material other than wood fl ooring, the fi re-
place shall be installed on a metal or wood panel extending the full width and depth.
If the optional fan or blower is installed, the junction box must be electrically connected and grounded in accordance with local
codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the ANSI/
NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
All sections with BCDV36CF(G) are common to both the BCDV36CF and the BCDV36CFG.
FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY!
BCDV36CF(G) -Maximum input for the BCDV36CF(G) is 17,000 BTU/h for natural gas and propane. Maximum output for
natural gas and propane is 10,900 BTU/hr at an effi ciency of 64% with the fan on. The A.F.U.E. (annual fuel utilization effi cien-
cy) rating is 53% for natural gas and propane.
BCDV42CF - Maximum input for the BCDV42CF is 24,000 BTU/hr for natural gas and propane. Maximum output for natural
gas and propane is 16,000 BTU/hr at an effi ciency of 67% with the fan on. The A.F.U.E. (annual fuel utilization effi ciency) rating
is 61.5% for natural gas and propane.
When the fi replace is installed at elevations above 4,500ft, and in the absence of specifi c recommendations from the local au-
thority having jurisdiction, the certifi ed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft.
Minimum inlet gas supply pressure is 4.5" water column for natural gas and 11" water column for propane.
Maximum inlet gas pressure is 7" water column for natural gas and 13"
water column for propane. Manifold pressure under fl ow conditions is 3.5"
water column for natural gas and 10" water column for propane.
This fi replace is approved for bathroom, bedroom and bed-sitting room
installations and is suitable for mobile home installation.
No external electricity (110 volts or 24 volts) is required for the gas
system operation.
Expansion / contraction noises during heating up and cooling down
cycles are normal and are to be expected.
GENERAL INSTRUCTIONS
GENERAL INFORMATION
CARE OF GLASS AND PLATED PARTS
Use only accessories designed for and listed with your specifi c fi replace.
Provide adequate ventilation air. Provide adequate accessibility clearance for servicing and operating the fi replace. Never
obstruct the front opening of the fi replace. Objects placed in front of the fi replace must be kept a minimum of 48" away
from the front face of the unit.
Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean
dry cloth. The BCDV36CF(G) and BCDV42CF are factory equipped
with tempered glass. The glass thickness is 3/16" for both models. Use
only replacement glass available from your Authorized dealer. DO NOT
SUBSTITUTE MATERIALS. Clean the glass after the fi rst 10 hours of op-
eration with a recommended gas fi replace glass cleaner. Thereafter clean
as required. DO NOT CLEAN GLASS WHEN HOT! If the glass is not kept
clean permanent discoloration and / or blemishes may result.