IR Water-Proof Network Camera User Manual Please read this instruction carefully for correct use of the product
Notes Before operation, we strongly advise users to read this manual and keep it properly for using later. Please use the specified power supply to connect. Avoid from in correct operation, shock vibration, heavy pressing which can cause damage to product. Do not use corrosive detergent to clean main body of the camera. If necessary, please use soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any cleanser for high grade furniture is applicable.
2 Mega Pixel IP Camera User Manual Table of Contents 1 2 3 4 5 Introduction ................................................................................................................... 1 1.1 Summarization ............................................................................................................. 1 1.2 Check Package Content ................................................................................................ 1 1.3 Overview ............................................
2 Mega Pixel IP Camera User Manual 6 7 8 5.5.5 DDNS Configuration ...................................................................................................... 24 5.5.6 RTSP ................................................................................................................................... 25 5.5.7 UPnP ................................................................................................................................... 25 5.5.8 Mail Setting ...........................
2 Mega Pixel IP Camera User Manual Page 1 1 Introduction 1.1 Summarization This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It adopts state of the art video processing chips. It utilizes most advanced technologies, such as video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to ensure this system more stable and reliable. This unit consists of two parts: the IP-CAM device and central management software (short for CMS).
2 Mega Pixel IP Camera User Manual Page 2 1.3 Overview This series of cameras support varifocal lens and prime lens. If the camera you get is prime lens, please skip the descriptions of the zoom and focus.
Page 3 2 Mega Pixel IP Camera User Manual 2 Installation 2.1 Install IP-CAM Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera and check whether the power supply is in conformity with your AC outlet. The mounting steps are as follows: ʒ Attach the drill template to the place where you want to fix the camera and then drill 4 screw holes according to the drill template.
Page 4 2 Mega Pixel IP Camera User Manual 2.2 Install CMS Find CMS software from CD and then double click “Setup.exe” file to pop up installation wizard. Install the software according to the prompts in the wizard. After you complete the installation, you will see the CMS and IP-Tool icon on the desktop. Please see the user manual of this software for more details. If you need to install IP-Tool separately, please double click IP-Tool installation package and install it according its wizard prompts.
Page 5 2 Mega Pixel IP Camera User Manual 3 IE Remote Access You may connect IP-Cam via LAN or WAN. Here only take IE browser (6.0) for example. The details are as follows: 3.1 LAN In LAN, there are two ways to access IP-Cam: 1. Access through IP-Tool; 2. Directly access through IE browser. 3.1.1 Access through IP-Tool ʒ Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the PC from the CD.
Page 6 2 Mega Pixel IP Camera User Manual administrator and click “Modify” button to modify the setting. ) The default password of the administrator is “123456”. ʕ Double click the IP address and then the system will pop up the IE browser to connect IP-CAM. IE browser will auto download the Active X control. After downloading, a login window will pop up as shown below. Input the username and password to log in. ) The default username is “admin”; the default password is “123456”. 3.1.
Page 7 2 Mega Pixel IP Camera User Manual Select “Property” and then select internet protocol according to the actual situation (for example: IPV4). Next, click “Property” button to set the network of the PC. ʓ Open the IE browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control automatically. ʔ After downloading Active X control, the login dialog box will pop up. ʕ Input the default username and password and then enter to view. 3.
2 Mega Pixel IP Camera User Manual Page 8 ʓ Go to Config ÆNetwork ConfigÆWired menu to modify the IP address. ʔ Go to the router’s management interface through IE browser to forward the IP address and port of the camera in the “Virtual Server”. Port Setup IP Setup Router Setup ʕ Open the IE browser and input its WAN IP and http port to access.
2 Mega Pixel IP Camera User Manual Page 9 4 Remote Preview 4.1 The Remote Preview Interface Icon z Description Motion alarm indicator icon Fix size Icon Description Sensor alarm indicator icon Start/Stop record Actual size Zoom in Playback Snap Zoom out Talk Full screen Enable audio When motion detection alarm is triggered, the people icon will turn red. Right click to pop up a pull-down list as shown below: Stream: Three streams are optional.
2 Mega Pixel IP Camera User Manual Page 10 The descriptions of the control panel are as follows: Button Description to rotate the dome upwardsͺ diagonally down-left; to rotate to rotate the dome towards rightͺ to rotate the dome to rotate the dome diagonally up-right; to rotate the dome the dome towards left; diagonally up-left;ͺ to rotate the dome downwards; to rotate the dome diagonally down-right; to stop rotating the dome. Drag the scroll bar to adjust rotating speed of the dome.
Page 11 2 Mega Pixel IP Camera User Manual 4.3 Snap Pictures Select the picture number, and then click “Snap” icon as shown below: Single Snap Snap multiple pictures Select the picture number from Frame pull down list box, such as 2, and check “Title” and “Time” to show capture title and time on the snap pictures simultaneously.
2 Mega Pixel IP Camera User Manual Page 12 5 Remote Live Surveillance Functions of remote configurations include: System Configuration, Video Configuration, PTZ Configuration, Alarm Configuration, Network Configuration and Advanced Configuration. You should firstly select the menu on the left, and then set the relative parameters. When one user configures parameters of a certain device, other users can not set this device. 5.
2 Mega Pixel IP Camera User Manual Page 13 5.1.2 Date & Time Configuration Setting steps: 1. Go to ConfigÆDate & Time menu as shown below. 2. Set time zone. 3. Enable DST mode as required. 4. Set time. You may set time manually or enable NTP. 5.1.3 SD Card 1. Go to “System Configuration” Æ“SD Card” as shown below: The first time you used the SD card, you should click “Format SD card”. Click “Eject card” to stop writing data to SD card. Then the SD card can be ejected safely.
Page 14 2 Mega Pixel IP Camera User Manual 5.2.1 Camera Configuration Setting steps: 1. Go to “Video Configuration” Æ “Camera” interface as shown below. 2. You may adjust brightness, contrast, hue and saturation of the picture. 3. Select white balance mode. 4. Wide dynamic, sharpen, and denoise are adjustable. 5. You can also set day-night mode and enable the image mirror and image overturn function. 6. You may frequency and repair bad pixel. 7. Press the “Save” button to save the settings. 5.2.
Page 15 2 Mega Pixel IP Camera User Manual quality better in a constant bitrate but also help to calculate the capacity of the recording. VBR means that the compression bitrate can be adjustable according to the change of the video resources. This will help to optimize the network bandwidth. Video Quality: When VBR is selected, you need to choose image quality. The higher the image quality you choose, the more bitrate will be required. Bitrate: Please choose it according to the actual network situation.
Page 16 2 Mega Pixel IP Camera User Manual To set up video mask 1. Enable video mask and select mask color. 2. Click “Draw” button and then drag the mouse to draw the video mask area. 3. Click “Save” button to save the settings. 4. Return to the live to see the following picture. Clear the video mask: Go to video mask menu and then click “Clear” button to delete the current video mask area. 5.2.5 ROI Configuration To set up ROI 1. Go to ConfigÆROI Config menu.
Page 17 2 Mega Pixel IP Camera User Manual 2. Check “Enable” and then click “Draw” button. 3. Drag the mouse to set the ROI area. 4. Set the level. 5. Click “Save” button to save the settings. Now, you will see the selected ROI area is clearer than other areas especially in low bitrate condition. 5.3 PTZ Configuration PTZ Configuration includes two submenus: Protocol and Preset. 5.3.1 Protocol 1.
2 Mega Pixel IP Camera User Manual Page 18 2. Input the protocol, address and baud rate according to the speed dome. 5.3.2 Preset Configuration 1. Go to “PTZ Configuration”Æ “Preset” to see an interface as shown below: Button Meanings to rotate the dome upwards; to rotate the dome towards left; to rotate the dome downwards; to rotate the dome towards right; to stop rotating the dome. Focus button. Click button to have long focus; click button to have short focus. Zoom button.
Page 19 2 Mega Pixel IP Camera User Manual 5.4 Alarm Configuration Alarm configuration includes six submenus: Motion Detection Area, Motion Detection Trigger, Motion Detection Schedule, Alarm Input Trigger, Alarm Input Schedule and Alarm Out. 5.4.1 Motion Detection Area 1. Go to “Alarm configuration”Æ “Motion Detection Area” to see an interface as below. 2. Move the “Sensitivity” scroll bar to set up the motion trace sensitivity. 3.
Page 20 2 Mega Pixel IP Camera User Manual 3. Set alarm holding time. 4. Set alarm trigger options. Alarm Out: If selected, this would trigger the external relay output on detecting a motion based alarm. Trigger Snap: If selected, the system will snap images on an alarm and save them in SD card. Trigger Email: If the email and attach picture checkbox is checked (Email address shall be set first in the Mail config interface), the triggered snap pictures and event will be sent into those address.
Page 21 2 Mega Pixel IP Camera User Manual 5.4.4 Alarm Input Trigger 1. Enter “Alarm Configuration”Æ “Alarm Input Trigger” to see a screen as shown below: 2. Select the sensor at the “Sensor” pull down list and set the sensor name and alarm type: NO and NC. 3. Enable alarm and select alarm holding time. 4. Set alarm trigger options. The setting steps are the same with that of motion detection trigger. Please refer to motion detection trigger chapter for details. 5.
Page 22 2 Mega Pixel IP Camera User Manual 1. Select the sensor which needs to setup the alarm parameter at the “Sensor” pull down list. 2. The following setup steps are similar to Motion Detection Schedule’s. Please refer to Motion Detection Schedule chapter for more details. 5.4.6 Alarm Out 1. Go to “Alarm configuration”Æ “Alarm output” as shown below: 2. Select alarm holding time and alarm name at the “Alarm out” and “Alarm holding time” pull down list box respectively. 3.
Page 23 2 Mega Pixel IP Camera User Manual device. 4. PPPoE: User needs to manual input the user name and password for dial-up internet. Firstly, log in IE clients and then enter user name and password of PPPoE, save the setting and exit. Secondly, set up IP address change notice. Thirdly, connect with Modem. Then the device will dial up internet automatically. 5. Press the “Save” button to save the settings. 5.5.3 Server Configuration Go to “Network Configuration”Æ “Server Config”. 1.
Page 24 2 Mega Pixel IP Camera User Manual selected, when the IP address of the device was changed, a new IP address will be sent to FTP server. 5.5.5 DDNS Configuration 1. Go to “Network Configuration”Æ “DDNS Configuration” tab as shown below. 2. Apply for a domain name. Take www. dvrdydns.com for example. Input www.dvrdydns.com in the IE address bar to visit its website. Then click “Registration” button to register as shown below. Create domain name.
Page 25 2 Mega Pixel IP Camera User Manual After you successfully request your domain name, you will see your domain in the list. 3. Select the server type and then input the username, password and domain name you apply for in the DDNS configuration interface. 4. Click “Save” button to save the settings. 5.5.6 RTSP Go to “Network Configuration”Æ “RTSP” interface as shown below. 1. Select “Enable RTSP server”. 2. RTSP Port: Access Port of the streaming media. The default number is 554. 3.
Page 26 2 Mega Pixel IP Camera User Manual 5.5.8 Mail Setting Go to “Network Configuration” Æ “Mail Setting” interface. 1. From Email: Sender’s e-mail address. 2. User name and password: Sender’s user name and password. 3. Server address: SMTP name of sender. 4. Select the secure connection type at the Secure Connection pull down list according to user’ actual needs. 5. Receival email address list: Add email address into the list. 6. Receival email address: Receiver’s e-mail address. 7.
2 Mega Pixel IP Camera User Manual Page 27 Please refer to the following table for parameters and instructions of FTP configuration. Parameter Meaning Server name The name of the FTP server Server address The address of the FTP server Port The port number of the FTP server User name The user name of the FTP server Password The password of the FTP server Path The save path for FTP files 5.
2 Mega Pixel IP Camera User Manual Page 28 2. Clicking “Modify” button will pop up “Modify user” dialog box as shown below. Modify User 3. Input original password of this user in the “Password” text box. 4. Input new password in the “New password” and “Confirmation” text box. 5. Input computer’s physical address which is used to access the server in the “User PC MAC” text box. 6. Click “OK” button to modify password and binding MAC address successfully. Delete user: 1.
Page 29 2 Mega Pixel IP Camera User Manual will display in the list box; the operation step of “Allow the following MAC address” is the same with “Deny the following IP address”. 5. Select the MAC address which needs to be deleted from the MAC address list box and click “Delete” button to delete that MAC address. 6. Click “Save” button to save the above setting. 5.6.3 Configure Backup & Restore Go to Advanced configurationÆConfigure Backup & Restore Interface.
Page 30 2 Mega Pixel IP Camera User Manual 5.6.4 Reboot Device Go to Advanced configuration—Reboot device to see an interface as shown below. Click “Reboot device” button to reboot the device. 5.6.5 Upgrade Go to Advanced Configuration—Upgrade interface as shown below. 1. Click “Browse” button to select the save path of the upgrade file. 2. Click “Upgrade server firmware” button to start upgrading the application program. 3. The device will restart automatically. 4.
Page 31 2 Mega Pixel IP Camera User Manual 6 Video Search Click “Picture” icon and search the images which saved in the SD card. 1. 2. 3. 4. Set time: Select date in the “Calendar” and choose the start and end time. Choose event “Motion” or “Sensor”. Click “Search” button to search the picture. Double click a filename or select a filename and then click “View” button in the list box to view captured pictures.
2 Mega Pixel IP Camera User Manual Page 32 Item 1 2 3 4 Buttons Explanations Close: Select certain picture and click this button to close this picture. Close all: Click this button to close all pictures viewing. Save: Click this button to select the save path of the picture file on the PC for saving the current picture. Save all: Click this button to select the save path of the picture files on PC for saving all pictures. 5 Fit size: The picture will fit on screen by clicking this button.
Page 33 2 Mega Pixel IP Camera User Manual 7 Q&A Q: How to find my password if I forget it? A˖Reset the device to the default factory settings. Default IP: 192.168.226.201 User name: admin Password: 123456 Q˖ ˖Fail to connect devices through IE browser, why? A: Network doesn’t connect well. Please check the connection and make sure it connected well. B: IP is not available. Reset the valid IP. C: Web port number has been revised: contact administrator to get the correct port number.
Page 34 2 Mega Pixel IP Camera User Manual ĺ Then click OK to finish setup. b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them. ˖No sound can be heard, why? Q˖ A˖Audio input device is not connected. Please connect and try again. B: Audio function is not enabled at the corresponding channel. Please check AUDIO item to enable this function. Q˖Why doesn’t the device connect to wireless? A: Check the statues of wireless router. Please make sure the router is open.
2 Mega Pixel IP Camera User Manual Page 35 8 Specification Model Camera 3 Megapixel IR Water-proof Network Camera Image Sensor 1/2.8͡CMOS Image Size 1920 × 1080 Electronic Shutter 1/25s~1/100000s Auto Iris Fixed Iris Min. Illumination 0 Lux (IR ON) Lens 8mm (6mm, 12mm, 2.8~12 optional) Day-Night Switch ICR auto switch WDR Digital WDR˄120dB WDR optional˅ DNR 3D noise reduction Video Compression H.264/MJPEG H.
