Installation Guide

ManualsBrandsCorbett Lighting ManualsChandeliersCorbett Lighting Bijoux 8 Light 26-1/2" Wide Chandelier with Crystal Accents

Page 1 of 2 300112ID

161-48 INSTALLATION INSTRUCTIONS

WARNING

DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.

READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.

CAUTION

 TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL

ELECTRICAL/BUILDING CODES.

 INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.

 If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached. DO NOT SEPARATE

ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING. In regular circumstances the BLACK

wire will be the “Hot” lead and the WHITE wire will be the “Neutral” or “Common” lead. A GREEN or BARE COPPER wire is the “Ground”. In

older buildings, it is always good practice to reconfirm the polarity of the wiring.

NOTICE

 The important safeguards and instructions outlined on this sheet

cannot cover all possible conditions and situations that may occur.

It must be understood that common sense, caution and care are

factors that cannot be built into any product. Caution and care must

be supplied by the person(s) installing, operating and caring for

this lighting fixture.

 This fixture is designed to be mounted on a correctly installed

standard round or octagon box or a through wiring box with a

plaster frame. The box must be securely mounted to the structure

of the building. The crossbar and hardware supplied should be

used. Directly mounting the fixture to the outlet box may make it

impossible to correctly align the fixture.

FIXTURE PREPARATION

1. Remove the fixture and parts bag(s) from the carton.

NOTICE:

Before discarding the carton, double check the contents

to make certain that all parts are found.

FIXTURE INSTALLATION

1. Attach the crossbar to the outlet box. (The green screw should face the floor).

2. Remove the threaded ring from the screw collar loop. Fully thread the loop onto

the nipple and tighten the set screw. Thread the hex nut onto the nipple and the nipple

into the crossbar. Place the canopy over the screw collar loop and against the ceiling.

Adjust the nipple so that 1/4" of threads on the screw collar loop extend beyond the canopy.

Tighten the hex nut against the crossbar. Using the ring, install the canopy.

3. Open the end links of the chain. Attach the chain to the screw collar loop.

Hang the fixture on the chain at the desired height. Remove excess chain.

Close the chain links. Unscrew the ring from the screw collar loop.

Allow the ring and canopy to slide down the chain to the fixture.

WARNING

The use of chain pliers for opening and closing links of chain is required. The use of tools other than chain pliers

may damage the chain link resulting in a failure which can cause harm to the fixture, property, and/or person(s).

Outlet box

Green screw

Crossbar

Hex nut

Nipple

Canopy

Screwcollar loop

Ring

Chain

Summary of content (2 pages)

PAGE 1
61-48 INSTALLATION INSTRUCTIONS WARNING DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION  TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.  INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
PAGE 2
4. Thread the lead wires and ground wire (first) through the threaded ring, then the canopy and up through alternating links of the chain until the ceiling is reached. 5. Measure 6" of lead wire beyond the top of the chain. Cut off the excess wire. Strip the insulation off the ends of the leads exposing approx. 1/2 " of wire. Twist the strands of wire together. Push the leads and ground wire up through the screw collar loop and nipple and into the outlet box. 6.