KITCHEN FAUCET MODEL: COS-KF548C USER’S MANUAL & INSTALLATION GUIDE
Thank You Thank you for your purchase. We know that you have many brands and products to choose from and we are honored to know that you have decided to take one of our products into your home and hope that you enjoy it. Our faucets are designed according to the strictest performance standards for the North American market. We follow the most advanced manufacturing philosophy. Each faucet leaves the factory after thorough quality inspection and testing.
Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Cosmo Appliances at 1-888-784-3108 Pre-drilled hole size requirement: 1-3/8” - 1-1/2” Max countertop thickness without deck plate: 1-3/8” Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean the sink of countertop to remove any debris, plumber's putty, or silicone.
TABLE OF CONTENTS PARTS DIAGRAM 04 PARTS INCLUDED 05 FAUCET DIMENSIONS 06 INSTALLATION PROCEDURES 08 OPERATING INSTRUCTIONS 12 TROUBLESHOOTING 14 3
31 4
5
6
The minimum distance between the faucet hole and the wall should be 3.5”. This is to ensure that the faucet lever can move freely allowing for full operation. If the distance between the faucet hole and the wall is less than 3.
Step 1 Remove the plastic holder, silicone ring, metal ring, and nut from the shank. Insert faucet through the top hole of installation site. Attach Plastic Holder (A), Silicone Ring (B), Metal Ring (C) under the faucet. Use the Nut (D) provided to hold sink and hardware into place. Once tightened, use the Screws (E) located on the nut to firmly secure into place. A. Plastic Holder B. Silicone Ring C. Metal Ring D. Nut E.
Step 2 Connect spray hose (B) to supply hose (A). Connect the hot and cold hoses to the hot and cold supply hoses of the faucet. Hoses on the faucet are labeled. C. Supply Hose C. Supply Hose A. Supply Hose B.
Step 3 Proper installation of the hose counterweight will ensure that the sprayer retracts smoothly. On the sprayer hose, measure 15" down from the body of the faucet and mark this point. Install the hose weight at this marked point. The sprayer should retract smoothly. Reposition the hose weight as necessary. Make sure the hot and cold hoses do not interfere with the spray hose. They can be repositioned slightly if necessary.
Step 4 Connect and tighten waterlines to hot and cold water supply (use Connect hot and (12)threads). to the angle with plumbers tape oncold the waterlines water supply Turnsto onand the tighten water supply a wrench snug,(DO thenNOT unscrew headON :&5 (8 YET), and checkuntil for leaks TURNspray FAUCET If no leaks are found turn the faucet on for 60 seconds to clear any debris from the water lines.
Usage How to Operate the Handle 25˚ Off On 90˚ LEFT COLD WATER 12 RIGHT HOT WATER 1. Pull the lever to the right to turn on the water. Push to the left to turn off 2. Pull the lever forward (towards you) to increase cold water flow and push the lever back (away from you) to increase the hot water flow.
Usage How to Operate the Sprayer 1. Turn on the handle, press the top position on button, for the spray function. 2.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 14 CAUSE ACTION Leakage under the handle. Locking nut has come loose . Unscrew the lever on the handle by hand. Loosen set screw with a hex wrench (2.5 mm). Remove the handle and unscrew trim cap by hand. Tighten cartridge nut with an adjustable wrench Water will not shut off completely Cartridge needs to be replaced.
Codes/Standards Applicable: • Certified to CUPC • Certified to AB1953 • Certified to NSF/ANSI 61 • ADA for lever handle WARRANTY AND SERVICE For full warranty details on this product please visit: http://www.cosmoappliances.
