Use and Care Manual
www.costway.com
1. motor stroke reset:
In the "E10, E20" alarm state or aer running to the lowest height posion, press and hold the key for 3
seconds, and release (Reset), the liing table will start running downwards and rebound to a certain
height, and the reset will display the lowest height.
2. Mul-motor stroke reset:
In the "E10, E20, E60" alarm state or aer running to the lowest height posion, press and hold the key
for 3 seconds, and release (Reset), the liing table will staro run downwards and re
bound to a certain
height. The reset will display the lowest height.
1)1. Liing
The desk will go up and down when pressing
or , along with the number shown on the
heighnterface changing.
2. Posion Invoking and Memory
The following operaons are performed under the height display interface.
A. Touch Key Handle
It shows “H1” when pressing
, then the desk will run to the sing posion when loosen it.
It shows “H2” when pressing
, then the desk will run to the standing posion when loosen it.
Press
and loosen it, heighnterface blinks, then press and loosen io save the current
heigho sing posion at last. Or press
and loosen io save the current heigho standing
posion at last. It will stop blinking and exit memory mode ihere is no numeric key pressed within
6 seconds.
B. Others
Press numeric key to invoke its corresponding height, and the desk will run to the posion you
invoked automacally.
Press
and loosen it, heighnterface blinks, then press numeric key( 、 、 ) to save
the current heigho the corresponding posion. It will stop blinking and exit memory mode if
there is no numeric key pressed within 6 seconds.
3. Screen Awaken
A. WN18H45 Touch Key Handle
The heighnterface will be closed aer lightening for a long me in order to avoid contacng
by mistake. You can long press
to awaken it.
B. Others
The heighnterface will be closed aer lightening for a long me. You can press any key to
awaken it.
4. Setup Mode
A. press
3 seconds, handle shows “S--" and blinks.
B. loosen
and press again to enter set up mode, it will display the funcon name, the
funcon can be listed as the followings:
Unit ohe height displayed on the screen: Unit (
);
Brightness ohe screen :Brightness(
);
On-off state ohe beep :Beep(
);
Force ohe collision protecon :Collision Force(
);
Seng ohe use height limitaon :Set Height(
);
Seng ohe demonstraon mode :Demo(
)
The funcon of each key in the seng mode:
/ Backspace key (back to previous menu)
Tab switch
Enter key (enter to next menu or confirm the current operaon)
It will exit seng mode ihere is no numeric key pressed within 20 seconds
Main menu
interface
Sub menu
interface
Descripon
Unit
SI Metric
The interface displays last height unit seng aer
entering. Use
or
to choose the height unit, and
press
to confirm and save it.
Inch
Brightness
Low
The interface displays last handle brightness seng
aer entering. Use
or to choose the brightness
level, and press
to confirm and save it. The system
will exit aer2seconds.
Normal
High
Beep
Off
The interface displays last buzzer seng aer
entering. Use
or to choose the buzzer condion,
and press to confirm and save it. The system will
On
Collision Force
Off
The interface displays last collision force aer
entering. Use
or to choose the force condion,
and press
to confirm and save it. The system will
exit aer 2 seconds.
Light
Normal
Heavy
Set Height
Original
①②
Use or to
choose the type
oeight aer
entering, and
press
to
confirm and
enter
corresponding
seng
interface.
The interface displays last original
height seng aer entering. Use
or to adjushe seng, and
press to confirm and save it.
Low
①③
The interface displays last lowest
limit seng aer entering. Use
or to adjushe seng, and
press to confirm and save it.
High
①③
The interface displays last highest
limit seng aer entering. Use
or to adjushe seng, and
press to confirm and save it.
10 11