Operator's Manual III IIII RRFTSMRN°! IIII II I 30" RIDING MOWER SIDE DISCHARGE ELECTRIC START Model No. 917.28001 I This product has a low emission engine which operates differently from previously built engines.
Warranty ................................................. Safety Rules ........................................... Product Specifications ............................ AssemblyiPre-Qperation ........................ Operation .............................................. Maintenance Schedule ......................... 2 3 6 7 11 18 Maintenance ......................................... t8 Service and Adjustments ...................... 23 Storage .................................................
| | DANGER: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Never direct discharged material toward anyone. Avoid discharging material against awalf or obstruction. Material may ricochet back toward the operator. Stop the blade when crossing gravel surfaces. • Do not operate machinewithoutthe entire grass catcher, discharge chute, or other safety devices in place and working.
Ii. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or ifyoufeel uneasy on it, do not mow it. • Mow up and down slopes (15° Max), not across. • Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneventerrain could overturn the machine. Tall grass can hide obstacles.
• Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from your vehicle when fitling. - Removegas-poweredequipmentfromthe truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS [GasolineCapacity 1.5 Gallons !andType: UnleadedRegular Oil Type (API SG-SL): Oil Capacity: SAE 30 (Above 32°F) SAE 5W30 (Below32°F) 48 Oz. Spark Plug: ChampionRC12YC (Gap: .030") GroundSpeed (Mph): Forward: Reverse: ChargingSystem: BladeBolt Torque: 3 Amps @ Battery 45-55 Ft. Lbs. 0- 4 0- 2 CONGRATULATIONS on your purchase of a new riding mower, It has been designed, engineered and manufactured to give you the best possible dependability and performance.
= Steedng Wheel Insert Steedng (1) 5t16-18 Hex Bolt Shaft (1) Front Bumper x 4 Stee_ng Extension (t) Rear Bumper Wheel (1) Lockwasher j_ Steedng I Steering Boot @ Wheel Adapter Steedng (4)Screw Shaft Cover #10 x 0,200 (1) Large Flat (1) Shroud Washer (1) Cup Washer (2)Key Slope Sheet Seat (I) Knob Your new riding mower has been assembled at the factorywith the exception ofthose parts left unassembled for shipping purposes.
TO INSTALL STEERING WHEEL 1. Slide extension shaft onto steering shaft. 2. Slide steering shaft protective foam cover over steering shaft. 3. Place steering boot over steering shaft and push down to secure. 4. Position fr0nt wheels ofthe riding mower so they are pointing straight forward. 5. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft, 7. Press steering wheel into position on shaft, install large washer, lock washer, bolt and tighten securely. 8.
TO ATTACH REAR BUMPER NOTE: For ease of assembly,you may wisl to obtain the assistance of another person for mountingbumper to riding mower. 1. Remove (4) screws from rear chassisof riding mower, 2. Position bumper as shownandassemble to rear chassis with screws removed in step 1. 3, Tighten the four (4) screws securely, TO ATTACH FRONT BUMPER NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting bumper to riding mower. 1.
t_CHECKLIST Before you operate your new riding mower, we wish to assure that you receive the best performance and satisfaction from this Quaiit,/Product. Please review the following checklist: J All assembly instructions have been completed. ,/ No remaining loose parts in carton. ,/ Battery is properly connected. ,I Seat is adiusted comfortably and tightened securely. ,/ All tires are properly inflated, (For shipping purposes, the tires were overinflated at the factory.
These symbols may appear on your riding mower or in literature supplied with the product. Learn and understand R their meaning.
KNOW YOUR RIDING MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR RIDING MOWER Compare the illustrations with your riding mower to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Brake Pedal Parking Lever Deck Clutch Lever IgniUon Switch Lift Lever Throttle/Choke Height Adjl Lever Motion Control Our riding mowers conform to the applicable safety standards of the American National Standards Institute.
The operation of any riding mower can result in foreign objects thrown into the eyes, which can result in severe eye damage, Always wear safety glasses or eye shields while operating your riding mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. GROUND DRIVE • Tostop ground drive, depress brake pedal all the way down. . Move motion control leverto neutralposition.
TO USE THROTTLE CONTROL Always operate engine at full speed (fast). • Operating engine at less than full speed (fast)reduces engine's operating efficiency. - Full speed (fast) offers the best mower performance. Throttle \ TO MOVE FORWARD AND BACKWARD The direction and speed of movement controlled by the motion control lever. t. Ensure the parking 2, Start riding mower with motion lever in neutral (N) position. 3. Release 4, Slowly desired parking is brake is applied.
REVERSE OPERATION SYSTEM (ROS) Yourdding mowerisequippedwitha Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the deck clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.
BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your riding mower has been shipped, from the factory, already filled with summer weight oil. 1. Check engine oil with riding mower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until "FULL' mark on dipstick is reached. Do not overfill.
MOWING TIPS - Mower should be properlyleveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut. Have the cut area to the right of the riding mower. This will result in a more even distribution of clippings and more uniform cutting.
MAINTENANCE R D I Check Operator, Presence & ROe Systems G (_ for Loose Check/Replace Clean BaKery Lubricate Friction Surfaces Check Mower L_velnes5 R; Check V-Beff SEASON STORAGE t/ ........... i/ v" v' v'0 i/ ,i,illllll iii =/ Check En,gine Oil Level Engine ....Ev_.Y F-E_o.E iv" V_3 and Spindles Axles EVERY 100 HOURS I v" Mower B|ad,e and Terminal5 Clean Change i/ EVERY 51) HOURS .
RIDING MOWER Always observe safetyruleswhen performing any maintenance. BRAKE OPERATION If riding mower requires more than four (4) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced at your nearest authorized service center. TIRES - Maintain tire pressure at 12 PSI. o Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
BATTERY Your riding mower has a battery charging system which is sufficient for normal use. - Keep battery and connectors clean. * Only recharge battery with charger approved for a 12V 6 amp. hour battery. • Charging with any other charger or an automotive style charger can cause permanent damage to the battery. * Charge battery for 24 hours for a full charge. NOTE: The original equipment battery on your riding mower is maintenance free. Do not attempt to open or remove caps or covers.
DECK WASHOUT PORT Your riding mower's deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the riding mower to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the riding mower's discharge chuteis directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover ff attached. 2.
CLEANING FRICTION SURFACES To ensure proper drive performance keep the friction surfaces free from dirt, chaff and excess rubber at all times. Every 25 hours of operation, the friction surfaces need to be rubbed clean with isopropyl alcohol or other non-filming cleaner. Engine Plate Friction Disc MUFFLER inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.
SERVICE ORTO WARNING: ADJUSTMENTS: AVOID SERIOUS INJURY, BEFORE PERFORMING ANY 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place deck clutch in "DISENGAGED" position. 4. Turn ignition key to "STOP" and remove key, 5, Ensure the blade and all moving parts have completely stopped. 6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug, RIDING MOWER TO REMOVE MOWER 1.
TO LEVEL MOWER HOUSING Adjust the mower while riding mower is parked on level ground or driveway. Ensure tires are properly inflated. If tires are over or underinflated, you will not properly adjust your mower. SI DE-TO-SIDE ADJUSTMENT • Raise mower to its highest position. • Measure distance "A" from bottom edge of mower to ground level at front corners of mower, Bottom Edgeof Mower to Ground BottomEdgeof Mowerto Ground t!! il .......
TO REPLACE MOWER BLADE DRIVE BELT TO ADJUST STEERING WHEEL ALIGNMENT Ifsteeringwheeicrossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the "INSTALL STEERING COLUMN" section of this manual. MOWER DRIVE BELT REMOVAL I. Park riding mower on a level surface. 2. Set parking brake. 3, Lower mower to its lowest position, 4. Remove mandrelcoverfrem mowerdeck. 5. Remove rear engine plate from unit. 6.
REPLACING BATTERY _t, WARNING: Do not short battery terminals by allowing awrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. t. Lift seat pan to raised position. 2. Remove terminal cover. 3. Disconnect BLACK battery cable then RED battery cabie, battery strap and carefully remove battery from riding mower. 4.
Immediately prepare yourriding mower for • Empty the fuel tank by starting the engine storage attheendoftheseason Orifthe and letting it run until the fuel lines and ridingmower wiltnotbeusedfor30days carburetor are empty. or more. • Never use engine or carburetor cleaner _kWARNING: Neverstorethe riding mower products in the fuel tank or permanent withgasoline inthetankinside a building damage may occur, where fumesmayreach anopenflame or • Use fresh fuet next season. spark.
TROUBLESHOOTING CHART: See appropriate section in manual PROBLEM CAUSE Will not start Hard to start unless directed to Sears service center. 1 2 3 4 Out of fuel. 1 Fill fuel tank. Bad spark plug. Dirty air filter. Water in fuel, 2 3 4 5 6 Loose or damaged wiring, Engine valves out of adjustment. Replace spark plug. Glean/replace air filter, Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter, Check all wiring.
TROUBLESHOOTING CHART: See appropriate section PROBLEM in manual unless directed Sears service center. tl CAUSE' CORRECTION .... ,,,,, , ,,,,,,,,,,, ,,,,, ,,, Poor cut - uneven cutting t 2 3 14 Worn, bent or loose blade. Mower deck not level. 1Buildup of grass, leaves, and trash under mower, Bent blade mandrel. 1 2 Replace blade. Tighten blade bolt. Level mower deck, 3 Clean underside of mower housing. 4 C]ogged mower deck vent from build.up of grass, leaves, and trash around mandrel.
SUGGESTED GUIDE FOR SIGHTING SLOPES ONLY RIDE UP AND NOT ACROSS HILL 15 DEGREES DOWN FOR SAFE OPERATION HILL, MAX. down the face of slopes, never across the face. Do not mow WARNING: To avoid serious injury, operate your tractor up and slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on stopes. 1. Fold this page along dotted line indicated above. 2.
Garantfa ............................................ ,.,, 31 Reglas de seguridad ............................. 32 Especificaciones del producto .............. 35 EnsambladoiPreoperaci6n ................... 36 Operaci6n ............................................. 40 Garantia para GARANTiA equipos COMPLETA tractores Programa de mantenimiento ................ Mantenimiento ...................................... Servicio y Ajustes ................................. Almacenamiento ......................
PELIGRO: Esta Maquina cortadora es capaz de amputar las manosy los pies y de lanzar objetos. si no se observan |as instruceiones de seguridad siguientes se pueden producir lesiones graves o ta muerte. _lb ADVERTENCIA: Con el fin de prevenir un arranque accidental cuando configure, transporte, ajuste o repare la m&quina, siernpre desconecte el cable de la bujia y coloque el cable deride no pueda entrar en contacto con la bujia.
II. OPERACION EN PENDIENTES IlL NiI_IOS ]_as pendientes son un factor principal que se relaciona con Ia p6rdida de control y Josaccidentes de voicaduras, Io que puede dar come resultado una lesion grave o la muerte. La operaci6n en ted,s las pendientes requiere tener precauciones extras. Si usted no puede retroceder de una pendiente o si se siente inc6modo en la pendiente, no la pode. •Pode las pendientes hacia arriba y hacia abajo (a 15° come mdximo), no de un Iado a otro.
• Nunca ]lene los recipientes adentro de un vehiculo o en un cami6n o trailer con forte de pl&stico. Coloque siempre los recipientes en el suelo y Iejos de su vehiculo du_ante el Ilenado. • Retire el equipo qua flJnciona con gasolina del cami6n o trailer y rellOnelo en el suelooSi esto no es posible, entonces reIlene este equipo con un recipiente port&tiI, en lugar de hacerlo directamente con Ia boquilla del dispensador de gasotina.
ESPECIFICACIONES DEL PRODUCTO Capacidad de gasolina y Tipo: Tipo de Aceite (APi-SG-SL): Capacidad de aceite: 1,5 GaIlones (5,6 L) Regular sin pJomo ._ SAE 30 (Sobre 32°F/0°C) SAE 5W30 (Deabajo32OF/0_C 48 onzas Bujfa: Champion RC12YC (Abertura: .030"/0,76 ram) Marcha Adelante: 0 - 4/6,4 Atr&s: 0 - 2/3,2 Velocidad de Recarrido: _ph/Kph) Sistema de Carga :3 Amps Bateria PARA Congratu]acionesporsu buena compra. Su nuevo producto Craftsman® estd diseSado y fabric.
Volante (t) Parachoques de la direcci6n traseros (t) Pamchoques delanteros de direcci6a (1) 5/t6-18 x4 Pemo de cabeza (1) Arandela de seguridad -Cobe_tura hexagonal (4) Tomillo #t0 x 0,200 E×tenci6n Adaptador (1) Shroud (1) Arandela (1) Arandeias taza D (2)Llave Hoja de pendiente Asiento (1) Manilla de ajuste Su nueva cortadora de c@sped se ha ensarnblado en la f&brica con excepci6n de aquellas partes que se dejan sin ensamblar para eJenvio.
PARA INSTALACI6N DE COLUMNA DE DIRECCION 6. 7. Deslice eI eje de extensi6n sobre el eje de direcci6n. Des]ice ia cubierta de espuma de protecci6n del eje de direcci6n sobre el eje de direcci6n. 3. Coloque eI manguito de direcci6n sobre e] eje de direcci6n y empSlejo hacia abajo para asegurarlo. 4. Coloque Iasruedas delar_erasde [acortadora de cL=sped de mode que apunten en Ifnea recta hacia adelante. 5. Retire el adaptador del volante y deslice el adaptador sebre el eje de direcci6n. 7.
COLOCACION DELANTERA DE LA DEFENSA NOTA: Para que el armado le resulte senciIIo, puedesolicitar ayudaa otra persona cuando monte la defensa en la cortadora de c_sped. 1. Retire los tornillos (2) deI chasis delantro de la cortadora de c_sped. 2, Incline la defensa delantera de modo que las pestaSas de la defensa entrenen las ranuras del frente del chasis y baje la defensa hacia su tugar. Coloque Ia defensa en el frente del chasis con los tornillos que retir6 en el paso t.
t_LtSTA DE REVISION Antes de operar su nueva cortadora de c6sped, deseamos asegurarnos de que usted obtenga el mejot desempeSo ysaUsfacci6nde este Producto de Calidad. Por favor revise la siguiente lista de revisi6n: J Todas Ias instrucciones de ensamblaje se ban completado. •/ No queda nhguna parte suelta en ]a caja de cartbn. La bateria est& bien conectada. J ,/ Et asiento est& ajustado c6modamente y bien apretado. ,/ Todas las Ilantas estdn bien infladas.
Estos simbolos pueden aparecer en ta cortadora de c_sped o en Ia literatura provista con el producto, Aprenda y entienda su significado. R MAP_CHA N ATR.
CONOZCA SU CORTADORA DE ClaSPED LEA ESTE MANUAL DEL PROPtETARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPEPAR SU CORTADORA DE ClaSPED Compare las ilustraciones con su cortadora de c_sped para familiarizarse con las ubicacionesde los diferentes controles y ajustes, Conserve este manual para futuras consultas.
La operaci6n de cualquier cortadora de c_sped puede causar que entren objetos extraEos en los ojos, 1oque puede provocar un daEo severe en los mismos. Use siempre lentes de seguddad o protecciones oculares mientras est_ operando la cortadora de c_sped o realizando cualquier ajuste o reparaci6n. Se recomienda usar una careta de seguridad de visi6n amplia sobre los anteojos o lentes de seguridad est&ndar.
PARA USAR EL CONTROL ACELERACION DE LA Eltango de altura de cortees de aproximadamente 1-1/2 a 4". Las alturas se miden desde el suelo hasta la punta de la cuchi]la con el motor sin funcionar. Estas alturas son aproximadas y pueden radar segdn las condic]ones de] suelo, laalturade[ c_sped y Iostipos de c@spedesque sevan a cortar. ° EIc_sped promedio se debe corr.araproximadamente a 2 i/2" (6.35 cm) durante la temporada frfa y a m_.s de 3" (7 cm) durante los meses de calor.
Correa el&stica Oorazadel deflector Cor_a eI_stica Oubierta de Ia alcochadora Cubiertade ta alcoch_dora FUNOIONAMIENTO ATRAS (ROS) Su cortadora de c@sped est& equipada con un Sistema de Operaci6n en Reversa (SOR). CuaP quier intento pot parte deI operador de avanzar en reversa con el embrague de la plataforma activado apagar& el motor, a menos que Ia llave de encendido est6 en la posici6n de "ENCENDIDO" (ON) deI SOR 3. Coloque bisagra. el deflector en la abrazadera 4.
TRANSPORTE At empujar o remolcar ta cortadora de c_sped, asegQrese de desactivar latransmisi6n al colocar la palanca de velocidades en neutral • Eteve el ajuste de altura de la cortadora de c@sped a su posici6n m&s alta con la palanca de ajuste de altura de Ia cortadora de c@sped. • Para volver a actJvar la transmisi6n, presione el freno y cambie la palanca de velocidades de neutral a otra posici6n.
ARRANQUE CON TIEMPO FRiO (50 ° F/IO°C Y MENOS) ° AI hacer arrancar el motor, mantenga el control de Ia aceleracion a la posfci6n de estrangulaci6n hasta qua el motor se caliente y empieze fundonar maI. Una vez que ernpieze a funcionar mat, mueva inmediatarnente el control de la aceIeraci6n a fa posici6n r&pida. El calentamiento del motor puede tomar a partir de varios segundos a varios rninutos (cuanto rn&sfrfa es la ternperatura, rn_s largo es el catentarniento).
ANTES DE CADA USO 1. Revise el nivel del _ceite del motor. 2. Revise I_ operaci6n det freno. 3. Revise la presi6n de las Ilantas. 4. Revise que los sistemas de presencia deI opemdor y de ROS funcionen bien. 5. Revise que los broches no est_n sue]tos. RECOMENDACIONES GENERALES La g_rantla par_ esta cortadom de c_sped no amparalos articulosquese hansometido alabuso o la negligenciadetoperation.
CORTADORA DE CESPED Siga s+empre las reglas de seguridad cuando realice cualquier mantenimiento+ OPERACION DEL FRENO Si Ia cortadora de c@sped requiere m_.s de cuatro (4) pies (t +219 metros) para detenerse a la velocidad m_txima sobre una super_cie de concrete o pavimento seco nivelado,entonces se debe dar servicio al freno en el centre de servicio autorizado m&s cercano, LLANTAS • Mantenga Ia presi6n de las Ilantas a t 2 PSI.
BATERiA CAMBIO La cortadora de c_sped tiene unsistema de carga de la bater|a que es suficiente para el use normal • Mantenga Ia baterta y los conectores limpios. • $61o recargue la bateria con un cargador aprobado para una bateria de 2.8 amperes hera de 12V. Determine el range detemperaturaesperado antes de cambiar el aceite. Todo el aceite debe cumplir con Ia clasificaci6nSG-SL de serviciode API. • AsegSrese de que lacortadora de c_sped est@ sobre una superficie nivelada.
PUERTO DE LAVADO DE LA CUBIERTA La cubierta de su tractor estA equipada con un puerto de Iavado sobre la superficie que forma parte del sistema de lavado de la cubierta. Se deberla utilizer cadavezque se haya usado elt factor. t. Ueve el tractor a un |ugar horizontal y despejado de su c@sped, 1o bastante oerca de una boca de riego como pare que Hegue la manguera del jardin. IMPORTANTE: Asegt_rese de que Ia boca de descarga del tractor est& orientada LEJOS de su case, garaie, coches aparcados, etc.
LIMPIEZA FRICCION DE SUPERFICIES DE Para asegurar un desempe_o de manejo apropiado, mantenga las superficies de friccibn libres de suciedad, residuos y exceso de goma en todo momento. Cada 25 horas de operaciSn, es necesario limpiar las superficies de fficci6n frot&ndolas con alcohol isopropilo u otro limpiador sin pelicula.
I_ CUALQUIER DVERTENCIA: PARA EVITAR SERVICIO O AJUSTE: UNA LESION SERIA, ANTES DE HACER I, Suelte por completo elpedalde embraguetfreno yaccione el frenode estacionamiento. 2. Coloque Ia palanca de control de movimiento en la posici6n neutral (N), 3. Coloque el embrague de la plataforma en la posici6n "DESACTIVADO", 4. Gire la Ilave de arranque a la posici6n "PARAD,_' y saque la llave. 5. AsegSresedequelacuchillaytodaslaspartesm6vilessehayandetenidoporcompleto. 6.
NIVELACION CORTADORA DE LA CARCASA DE CESPED AJUSTE DEL FRENTE A LA PARTE POSTERIOR DE LA IMPORTANTE: La plataforma debe estar nivelada de lado a [ado. Ajuste la cortadora de c_sped mientras est_ estacionada en et suelo o en un camino nivelado. Aseg_rese de que tas Ilantas est6n bien infladas (Observe la parte lateral de la [lanta para verificar que la PSI sea correcta). Si [as Ilantas est&n infladas de m&s o de menos, usted no podr& ajustar bien la cortadora de c_sped.
CAMBIO DE CINTA DEL IMPULSOR LA CUCHILLA DE LA CORTADORA ClaSPED RETIRO DE CINTA DEL IMPULSOR CORTADORA DE CESPED 1. 2. 3, 4, DE DE DE LA Estacione la cortadora de c@spedsobre una superficie nivetada. Accione el freno de estacionamiento, Baje Ia cortadora de c_sped a su posici6n m_.s baja, Retire la cubierta del mandril desde la plataforma de ta cortadora de c6sped. 5, 6. Retire Ia placa det motor posteriorde ta unidad. Retire la sujeci6n de ta cinta posterior de la unidad.
ARRANQUE DEL MOTOR BATERiA DESCARGADA CON UNA 6. Renistale la abrazadera y el pemo de Ia bated& _IIPRECAUCI6N: [_as bateria_s de plomo &cido generan gases e×plosivos. Mantenga los matedales que producen chispas,llamas y humo lejosde las baterias. Use siempre una protecci6n para los ojoscuando est_ cerca de las baterlas. Si su baterla est_ demasiado baja como para arrancar el motos, _sta se debe recargar. (Consuite Ia parte de "BATERIA? en ]a secci6n de Mantenimiento de este manual).
Prepare de inmediato su cortadora de e@sped para almacenarla al final de ia temporada o si no Io va a utilizar durante 30 alias o m&s. • Nunca use productos limpiadores para motor o carburador en eltanque decombustibleporque puede ocurrir un dafio permanente. A ADVERTENCIA: Nunca almacene la cortadora de c_sped con gaso]ina en el tanque adentro de un edificio deride los humos puedan alcanzar una flama abierta o una chispa.
IDENTIFICACION DE PROBLEMAS: Veala secci6napropiadaen elmanuala menos queest_ dirigidoa uncentrede servicioSears. CAUSA PROBLEMA No arranca Dificultad arragcar para CORRECCION t No tiene combustible, 1 Llene e] tanque de combustible, 2 3 4 Buj_a defectuosa, Filtro de aim sucio. Ague en el combustible. 2 3 4 5 6 Cableado suelto 0 dafiado. I_as v&Ivulas del motor estdn desajustadas.
IDENTIFICACI6N Vea la secci6n DE PROBLEMAS: apropiada PROBLEMA en el manual a menos que est_ dirigido a un centre CAUSA de servicio El motet sigue funcionando cuando el operador deja el asiento con elembrague activado 1 Sistema de control de presencia de seguridad deI operador defectuoso, Carte deficients - carte no uniforme 1 CuchilIa desgastada, doblada o suelta, t Revfse el cableado_ los interroptores y las conexiones.
GU{ASUGERIDAPARA MEDIR LAS PENDIENTESCON LA VISTA PARAUNA OPERAClONSEGURA O3 _O ! _b y abajo de _as Pend[entes, nunca transversa]mente con respecto alas I ADVERTENCIA: Para evltar da_os msyores graves, hags su tractor arriba I pendlentes. No cotter pend[entes de 15funsionar grados. Hags los vlrajes gmdualmente para evitar volcarse o le p_rdfda de control. I Tenga mucho cuidado ¢uando cambie de direcci6n en las pend]entes. 1. P{egar eeta pdglna a ]o largo de la Ifnea punteada arriba fndlcada. 2.
NEED MORE HELP.:' i YoU|t find the answer and more on raaaagemyhome.cora - for free! i • Find this anda[[yourother product manuals onSne, • Getanswers fromourteamofhomeexperts. _ i •Geta persona|ized maintenance ptanforyourhome. - Find information andtooL_ tohelp _th homeprojects.