I CRnFTSMAN I 120/240 VOLT ® 7000 WATT o SAFETY GUmDELmNES iMPORTANT: Read the Safety Guidemines and All mnstructions Carefully o ASSEMBLY o OPERATmON o MNNTENANCE o TROUBLESHOOTmNG o F_EPAmR PARTS Sold MGP-670070 Rev 0 12/40/99 by Sears Canada, Uric,, Toronto, Ont, M5B2B8
HORSE POWER GASOLINE CAPACITY OraLCAPACITY DATE PURCHASED: 14 HP 7 GALLON/26.5 LITERS 48 OZ./1.4 LITERS MODEL NO: SERIAL NO: MAmNTENANCE 1 AGREEMENT The Craftsman Warranty, pHusa Maintenance Agreement, provide maximum vaHue for your Sears products. Contact your nearest Sears store for detaiHs. STORE WHERE PURCHASED: ADDRESS: CUSTOMER CITY: RESPONSmBmMTmES Read and observe the safety ruHes. TELEPHONE: Follow a reguHarscheduHe in maintaining, caring for and using your generator.
This manuaH contains information that is important for you to know and understand. This information reHates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To heHpyou recognize this information, we use the symboHs to the right. Hease read the manuaH and pay attention to these sections.
READ AND UNDERSTAND ALL WARNINGS BEFORE ATTEMPTBNG TO OPERATE GENERATOR° RBSK OF ELECTROCUTBON AND FBRE .(¢ont'd} HAZARD WHAT COULD HAPPEN Operation of generator in rain, wet, icy, or flooded conditions. Water is an excellent conductor of ebctricity! Water which comes in contact with electrically charged components can transmit electricity to the frame and other surfaces, resulting in electrical shock to anyone contacting them. Operate generator in a clean, dry, well ventilated area.
READ AND UNDERSTAND ALL WARNINGS BEFORE ATTEMPTBNG TO OPERATE GENERATOR° RiSK OF FiRE HAZARD WHAT COULD HAPPEN HOW TO PREVENT iT Attempting to fill the fuel tank while the engine is running. Gasoline and gasoline vapors can become ignited by coming in contact with hot components such as the muffler, engine exhaust gases, or from an electrical spark. Turn engine off and allow it to cool before adding fuel to the tank.
READ AND UNDERSTAND ALL WARNNNG$ BEFORE Risk of in'u.Lu_r_z and Pro eper_vtDa_ao_lLe When Trans_q Generater HAZARD Fire, hhaiation, Surfaces WHAT COULD HAPPEN Damage to Vehicle Fuei or oii can bak or spill and couid resuit in fire or breathing hazard, serious injury or death can resuit. Fuei or oii baks will damage carpet, paint or other surfaces in vehbbs or traibrs. RISK OF BREATHING HAZARD Gasoline engines produce toxic carbon monoxide exhaust fumes.
READ AND UNDERSTAND ALL WARNINGS BEFORE ATTEMPTBNG TO OPERATE GENERATOR° RiSK OF UNSAFE HAZARD Operation manner. of generator OPERATION HOW TO PR_:V_:NT iT WHAT COULD HAPPEN in carebss Review and understand all of AH sources of energy include the potential for injury. Unsafe operation or maintenance of your generator could lead to serious injury or death to you or others. the operating instructions and warnings in this manual. Become familiar with the o operation and controls of the generator.
REAO ANO UNDERSTAND ALL WARNINGS BEFORE ATTEMPTBNG TO OPERATE GENERATOR° RiSK OF HOT SURFACES HAZARD WHAT COULD HAPPEN Contact with hot engine and generator components. Contact with hot surfaces, such as engines exhaust components, could result in serious burns. RiSK OF MOVING HAZARD I _ HAZARD Lifting a very heavy object. rvIGP 670070 The generator contains parts which rotate at high speed during operation. These parts are covered by guarding to prevent injury.
CARTON CONTENTS 1 ° Parts Bag t = Owner"s Manua! "t *_ o TwisBeck Plug L14=30P To be installed and/or used in accordance with appropriate HocaHeHectricaHcodes and reguHafions.
Read owner's manual. Do not attempt to operate equipment until you have read Owner's Manual for Safety, Assembly, Operation, Maintenance, Storage Instructions. TOOLS 121111- NEEDED Handle Assembly secured te top frame FOR ASSEMBLY Box Cutter or Knife 1/2" Wrenches Pair Wire Pliers Hammer 1/2" Socket and Socket Wrench 1/4" Socket and Socket Wrench 1 - 1" thick x 1 ' square piece of wood REMOVE GENERATOR FROM CARTON Open carton from top. Cut carton along dotted lines.
INSTALLATmON OF BATTERY Attach one end of the negative (black) cable negative (-) terminal on the battery. Recommended Battery for Electric Start: 12V - 45 A H. or 210 CCA (Cold Cranking Amps) Attach the other end of the negative (black) cable to the frame as shown. Install the star washer between the cable and the frame. Purchase battery and battery hardware separately, not included with unit. Place battery in rack with terminals facing towards generator head.
mNSTALUNG WHEEL KmT Place the fiat washer (7) against the wheel bushing and slide the cotter pin (4) through the drilled hole of the axle (2). Bend the cotter pin (4) to secure in place. The Craftsman Wheel Kit was designed to greatly improve the portability of your generator. kit. Failure engine. Drain gas and oil before assembling the portability to do so will cause damage to the Tighten lock nuts on wheel brackets.
KNOW YOUR GENERATOR Read this Owner's Manual and Safety Rules before operation of your Generator. Compare this illustration with your generator to famiHiarize yourseHf with the location of various controHs and adjustments. Save the manuaH for future rderences.
Your generator is equipped with: one 120 voHtGFCI dupHex receptacle a 15 amp circuit breaker protected by one 120 voHt3-prong twisflock receptacle protected by a 30 amp circuit breakers one 240 voHt4-prong twisflock receptacle protected by two 30 amp circuit breakers The circuit breakers are provided to protect the generator against eHectricaHoveHoad. If the circuit breaker trips, unpHug eUectricaHHoadfrom receptacle. Let circuit breaker cooHdown and then push circuit breaker button to reset.
Full An extension cord that is hot to the touch is oveHoaded, Repair or replace damaged Connecting Supp(y Generator extension To Main cords E(ectrica( Potential hazards exist when a ebctrba] generator is connected to the main ebctrba( supply coming into the house, It is at that point that the generator could feed back into the utility company's system causing possible electrocution of workers who are repairing electrical lines.
For recoil start: To Start Your Generator Never run engine in enclosed, poor ventilated areas. exhaust contains carbon monoxide, ordoriesa and deadly indoors Hace OFF/RUN/START switch in the RUN position. or Engine an gas. iMPORTANT: Make sure the battery is property serviced, fully charged, and assembbd before starting. Grasp handle on rope starter and pull slowly until resistance is fell Let the rope rewind slowly. Pull rope with a rapid full arm stroke. Let rope rewind slowly.
CONNECTmNG ELECTRmCAL Let engk_e run and warm starting with no ebctrbai Connect ioads in the following LOADS up for five minutes ioad. manner Voltage sensitive equipment should be the last equipment connected to the generator. Plug voltage sensitive appliances such at TV's, VCR's, microwaves, ovens, computers, and cordless telephones into a UL listed voltage surge protector, then connect the UL listed voltage surge protector to the generator.
GENERAL RECOMMENDATmONS The warranty of the generator does not cover items that have been subjected to operator abuse or negligence+ To receive full value from the warranty, operator must maintain the generator as instructed in this manual+ I Plug J J Some adjustments wiii need to be made periodically to maintain your generator+ GENERATOR Your generator should be kept clean and dry at all times+ The generator should not be stored or operated in environments that include excessive moisture, dust or a
Addfreshoil SeeAdd EngineOil intheOpera= tier sectionof thismanual Startandrunengineat idHe to checkforHeaks. Stopengine.Re-checkoiHHeveH, addoiHif required. Air Cleaner Clean Cooling System Debris may cHog the engine's air cooHing system_ Remove bHower housing and dean area shown to prevent overheating and engine damage. Clean Clean and Replace Spark Plug Check spark pHugyearHyor every 1O0 operating hours. CHean area around spark pHug. Remove and inspect spark pHug.
GFCm receptacme mnterrupter} (Ground Faumt Circuit For maximum protection against ebctrbai GFCI shouid be tested montHy. shock the To test: 1. 2. Depress the TEST button. The RESET button shouid extend. If the RESET button does not extend, notify a Authorized Service Center. To restore power, depress into the GFCI unit untii an reset properiy, the RESET surface of the test button. in, the power is ON. z m 4H the RESET button firmiy audiMe chick is heard.
PROBLEM Engine wifl not start No electHcM output CA USE 1. Low on fuei or oil 1, Add fuel or oii, 2. Ignition switch in "Off" position. 2, Turn to "ON" position 3. Fauityspark 3, 4. Choke in wrong position. 4, Adjust choke accordingly, 5. Fuei shut-off vaive in dosed position. 5, Open fuel shut-off valve, 6. Unit ioaded during start-up. 6, Remove load from unit, 7. Spark piug wire ioose, 7, Attach wire to spark plug, 1. Fauity receptacb. 1.
Briggs& Stratton Corporation (B&S), the California Air Resources Board (CARD) and the United States Environmental Protection Agency (U.S. EPA) Emission Control System Warranty Statement (Owner's Defect Warranty Rights and Obligations} EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 WHICH ARE PURCHASED AND USED ELSEWHERE IN THE AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND UNITED STATES.
3 TORQUE 1 20=25 IN=LBS TORQUE 14 11 TORQUE 20=30 IN=LBS AFTER SETTING ENGINE SPEED _.. 4 25=30 IN=LBS 1 TORQUE 120=144 IN=LBS 13 TORQUE 120=144 IN=LBS KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 TORQUE 20=25 IN=LBS DESCRIPTION FUEL TANK SCREWS FUEL TANK FUEL CAP HEAT SHIELD FRAME ASSEMBLY END COVER SCREW #10-24 x 9/16 FUEL HOSE FUEL LINE CLAMP SCREW, HEX CAP 5/16-18 x 1.25 SCREW #10-32 x 1/2 GROUND LUG SCREW 5/16-18UNC 2A WASHER .8750D .3751 D .
CRAFTSMAN 7000 GENERATOR 9t 9°670070 GENERATOR 21" TORQUE 60=70 IN=LBS 20 9 INSERT 17 /16 18 TORQUE IN SQUARE HOLES 14 15 120=144 IN=LBS KEY NO, 14 15 16 17 18 19 19A 20 21 22 23 DESCRIPTmON PART NUMBER ENGINE (model # 294447-1042-E1) SCREW 5/16-18 x 3/4 GROUND STRAP LOCK WASHER LOCK NUT ISOLATOR ISOLATOR REAR ISOLATOR SPACER SCREW 1/4-20 x 3/4 FUEL SHUT-OFF VALVE DRAINCOCK GROMMET SS-12-CD GS-0118 SSN-1619-ZN SSF-8150 GS-0033 GS-0033 GS-0492 91895680 GS-0437 GS-0446 *SEE ENGINE PAGES 30-3
CRAFTS_,_AN 7000 GENERATOR GENERATOR 0t0o670070 1 / / ORENT WITH VENTS DOWNWARD AS HEAD ASSEMBLY SHOWN 2 5 3 TORQUEUNTILTHREADSRUNOUT TORQUE 204-264 IN-LBS / 9 10 / / 12 TORQUE 60-70 IN-LBS f 113 116 SHOWN REFERENCE _17 FOR TORQUE 30-40 IN-LBS ONLY 8 TORQUE 120-144 IN-LBS \ \ \ \ \ \\ 21 INSERT GROOVE, SCALE CAPACITOR KEY NO, 1 2 3 4 5 6 7 8 9 10 11 12 16 17 21 INTO O-RING PART OF 10 1:1 WIRING DESCRIPTION DRIVE END ADAPTER LOCK WASHER 3/8 CAP SCREW 3/8-16 x 1 ROT
CRAFTSMAN 7000 GENERATOR 9t 9°670070 PANEL ASSEMBLY 3 TORQUE 12 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 MGP670070 DESCRmPTION PANEL ASSEMBLY PANEL COVER SCREW 10 - 9 X .50 SCREW #6-32 X .5 TORX NUT, SPEED #6 - 32 120V DUPLEX GFCI RECEPTACLE NUT, HEX JAM CiRCUiT BREAKER 15 AMP 3 PRONG TWISTLOCK 4 PRONG TWISTLOCK CIRCUIT BREAKER 30 AMP 26 -- ENG PART NUMBER GS-0928 GS-0017-1 SSF-3156 SSF-583 SSF-584 GS-0806 SSF-595 GS-0024 GS-0021 GS-0455 GS-0026 GS-0046 OF 10 BN=LBS.
CRAFTSMAN 70GG GENERATOR 9t9,670070 WHEEL KiT 14 13 10 10 KEY NO, DESCRiPTiON PART NO, 1 2 3 4 5 6 7 8 9 lO 11 12 13 14 15 16 WHEEL (2 USED) AXLE AXLE SPACER(2 USED) COTTER PiN WHEEL BRACKET(2 USED) AXLE END CAP FLAT WASHER, 3/40D X 11/16 ID SCREW, 5/16-18 X 1-3/4 (3 USED) LOCK NUTS (7 USED) SCREW, 5/16-18 X 1-3/4 (4 USED) BASE END CAPS (2 USED) FLAT WASHER, !-5/16 OD X 5/8 ID (2 USED) HANDLE ASSEMBLY (2 USED) HANDLE GRiP (2 USED) LOUVERED HEAT DEFLECTOR(NOT SHOWN) SCREW, HH #8-32 (4 USED) (NOT
CRAFTSMAN 7000 GENERATOR 9t0=670070 WmRING DIAGRAM OOOG DOOO OOOG CONTROL PANEL REAR VI EW TO ENGINE STARTER TO ENGINE REAR HOUSING ViEW (MALE) SOLENOID MAGNETO REAR HOUSING VIEW (FEMALE) 15A 120V GFCl 30G 3OA C/B \ / \ / 2X VIEW MGP670070 "A" 30A 120/240V, KEY NO.
CRAFTSMAN 7000 GENERATOR 9t9,670070 WiRE ASSEMBLY NOTE: (_ LEADS Q TAPE CONDUIT WITH 3/4 " WiDE IN AREAS SHOWN, TO PRODUCE TO ENGINE TAPE CODUIT WiTH Q SLACK ".£ "-. SEEDE3:AIL "A" STATOR LEADS (1,2,3,4) CO W,ND,.G ' I I " vT ! ................. ," 50UF_CAPA_ITOR KEY NO, 1 2 3 4 5 6 8 9 10 11 REAR VIEW HOUSING (MALE) (_ I AUX "A" TAPE. 22 _25 IN LONG ROTOR WINDING DETAIL ELECTRICAL + 23+_25 IN. LONG ,''" 3/4 " WiDE SLACK ELECTRICAL TAPE A SECURE TEE JOINT.
CRAFTSMAN 7000 GENERATOR 18_ 614_ 919.070070 Briggs & Stratton Model No. 294447=1257=E1 691 _7_8 dP 17 276 "k REQUIRES SPECIAL SEE REPAIR 158 TOOL iNSTRUCTiON TO iNSTALL. MANUAL 22_ 34 34 1029_ 33 , 276A GRAPROIL fi 42 GRAPHOIL fi @ 1022_ 40_ 1022_ 36 42 40_)@ 42 42 REQUIRES SPECIAL TOOLS TO iNSTALL. SEE REPAIR iNSTRUCTION MANUAL. No.
CRAFTSMAN 7000 GENERATOR 919.
CRAFTSMAN 7000 GENERATOR 919.670070 Briggs & Stratton Model No.
CRAFTSMAN 7000GENERATOR 919.670070 523 Briggs _ & Stratton Model No.
CRAFTSMAN 7000 GENERATOR 919.070070 Briggs & Stratton Model No.
CRAFTSMAN 7000 GENERATOR 919.670070 Briggs & Stratton Model No. 294447-1257-E1 \ \ 797A \ 801 797 @ 305A 1124 I K_No, 304 305 305A 309 310 311 413 510 544 697 797 Part No, 808055 692539 805247 691564 690323 497608 693587 496881 693548 805247 92278 1036 EM{SSIONS LABEL Description Blower Housing Screw (Blower Housing) Screw (Blower Housing) Starter Motor Bolt (Starter Motor) Brush Set Nut (Starter Motor) Starter Drive Starter Armature Screw (Drive Cap) Nut (Brush Retainer) I _305 _No, 7
CRAFTSMAN 7000 GENERATOR 919.670070 Briggs 358 ENGINE GASKET SET 1095 VALVE GASKET SET & Stratton Model No.
-- ENG lvlGP 670070
MGP 670070 38-- ENG
-- ENG lvlGP 670070
Dear Customer, In manufacturing this product, many steps have been taken to provide you with the highest quality. Unfortunately, errors or omissions occasionally occur. In the event that you find a missing or defective part, please contact your nearest Sears store. SERVICEAND REPAIRPARTS CALL1o800o665o4455 * Keep this number handy should you require need to order repair parts. If ordering a service call or parts make sure you have the name, make and model no.