Owner's Manual JCRRFTSMRN'J 20.0 HP ELECTRIC START 46" MOWER AUTOMATIC GARDEN TRACTOR EZ 3 Model No. 917.272960 • • • • Safety Assembly Operation Maintenance • Repair Parts This product has € low emission engine which Operates differently from prey ous y built engines. Before you start the engine, read and understand this Owner's Manual.
Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications.......................... 5 Assembly .............................................. 7 Operation ............................................ 12 Maintenance Schedule ...................... 19 Maintenance ....................................... 19 Service and Adjustments ....................23 Storage ...............................................31 Troubleshooting .....
IMPORTANT: This cuttingmachine is can resultin severe injuryor death. All capable of amputatinghands and feet slopesrequireextra caution.If you cannot and throwingobjects.Failureto observe back up the slopeor if you feel uneasyon the following safety instructionscould it, do not mowit. DO: resultin serious injuryor death. GENERAL OPERATION • Mow up and down slopes,not across. • Read, understand,and follow all • Remove obstaclessuch as rocks,tree instructionsin the manualand on the limbs,etc.
• Before andwhenbacking, lookbehind anddownforsmall children. • Never carry children.They may fall off and be seriouslyinjuredor interfere with safe machine operation. • Never allow childrento operate the machine. • Use extra care when approaching blind corners,shrubs,trees, or otherobjects that may obsGurevision. SERVICE • Use extra care in handlinggasoline and otherfuels. They are flammable and vapors are explosive. Use only an approvedcontainer. - Never remove gas cap or add fuel with the engine running.
_lLLook for this symbol to point out important safety precautions. It means CAUTION!H BECOMEAWARE!!! YOUR ,_FETY IS INVOLVED. CAUTION: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs always disconnect spark plug wire and place wire where it cannot contact spark g. P_CAUTION: Do not coast down a hill in neutral, you may lose control of the tractor. PRODUCT SPECIFICATIONS GASOLINE CAPACITY AND TYPE: OILTYPE _PI-SF/SG/SH): OILCAPACITY: 3.
Steering Wheel Steedng Wheel Insert Seat (_) i_(1) (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Shoulder Bolt 5/16-18 Knob Mower (4) Retainer Springs (single loop) (3) Retainer Springs (double loop) Gauge (2) Shoulder Wheels x 7/8 x 14 Gauge Bolts Q (2)lockNuts Center-
VideoCeeee_e Slope Sheet Keys _m (2) Keys Yournew tractorhas been assembledat the factorywith exceptionof those parts left unassembledfor shippingpurposes.To ensure safe and properoperationof your tractorall parts and hardware you assemble mustbe tightenedsecurely.Use the correcttoolsas necessaryto insurepropertightness.Reviewthe videocassette before you begin. TO REMOVE TRACTOR FROM TOOLS REQUIRED FOR ASSEMBLY CARTON UNPACK A socketwrenchset will make assembly easier.
BEFORE REMOVING TRACTOR OFFSKID ATTACH STEERING WHEEL • Remove hexbolt,lockwasher and largeflatwasher fromsteering shaft. HOW TO SET UP YOUR TRACTOR CHECK BATTERY • Lifthood to raisedposition. • If this battery is put into serviceafter monthand year indicatedon label (label locatedbetween terminals) charge batteryfor minimumof one hour at 6-10 amps. (See "BATTERY" in Maintenance sectionof this manual for charginginstructions). • Positionfrontwheels of the tractorso they are pointingstraightforward.
NOTE: You may now roll or drive your tractor offthe skid. Follow the appropriate instructionbelow to remove the tractor from the skid. TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal. • Place freewheel control in freewheeling position to disengage transmission (See TO TRANSPORT" in the Operation section of this manual).
• Installone front linkin top holeof the R.H. front mower bracketand R.H. front suspensionbracket. Retain with two single loop retainerspringsas shown. • Installsecondfront linkin L.H. front suspensionbracket only and retain with single loop retainer springas shown, •Tum height adjustmentknobcounterclockwiseuntil it stops. • Lower mower linkage with attachment liftcontrol. • Place the L.H. suspensionarm on inwardpointingdeck pin.
l/CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEWTHE FOLLOWING CHECKLIST: ,/ All assemblyinstructionshave been completed. 4" No remainingloose parts in carton. 4" Batteryis properlypreparedand charged. (Minimum1 hour at 6 amps). 4" Seat is adjusted comfortablyand tightened securely. 4 All tires are properlyinflated. (For shippingpurposes,the tires were overinflatedat the factory).
Thesesymbols mayappear onyourtractor orinliterature supplied withthe product, Learn and understandtheir meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ..=,...
KNOWYOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Comparethe illustrationswith yourtractorto familiarizeyourselfwith the locationsof variouscontrolsand adjustments. Save this manualfor futurereference. Amme_r Ignition Switch Attachment Clutch Switch Lever Plunger Throttle Clutch/ Brake Pedal Attachment LiftLever Choke Control/ Brake Lever Adjustment Knob Lever Free Wheel Our tractorsconformto the safety standardsofthe AmericanNationalStandards Institute.
the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments We recommend wide vision safety mask he operationorofrepairs. any tractor can result ina foreign objects thrown into over spectacles or standard safety glasses. I_ HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE Your tractor is equipped with an operator presence sensing switch.
The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.
• Do not pushor towtractorat more than two (2) MPH. • To reengage transmission,reverse above procedure. NOTE: To protecthoodfrom damage when transportingyourtractoron a truck or a trailer,be sure hood is closedand securedto tractor. Use an appropriate means of tyinghoodto tractor(rope, cord,etc.). r TOWING CARTS AND OTHER ATI'ACHMENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing.
• Insert key into ignitionand turnkey clockwise to "START"positionand release key as soon as engine starts. Do not run startercontinuouslyfor more than fifteensecondsper minute. If the engine doesnot startafter several attempts,push choke control in, waita few minutesand try again. If engine stilldoes not start, pullthe choke controlout and retry.
• Sittingin the tractor seat, startengine. Afterthe engine is running,move throttlecontrolto half (t/2) speed.With motioncontrollever in neutral (N) position,slowly disengageclutch/ brake pedal. • Slowlymove motioncontrollever forward,afterthe tractormoves approximatelyfive (5) feet, slowly move motioncontrollever to reverse position.After the tractormoves approximatelyfive (5) feet returnthe motioncontrollever to the neutral (N) position.Repeat this procedurewith the motioncontrollever three (3) times.
FILL IN DATES Check Brake operation Check Tire Pressure _ T Check Operator PreSence Interlock Systems R Check for Loose Sharpen/ReplaOe T Lubrication 0 Check Battery R Clean and Fasteners Mower _ I1_ Battery and Terminals I_ Co_ing A_ust Blade Motion Drive Belt(s) Belt(s) Tension _s TensiOn Check Engine Oil Level Change lidd* Level Adju_ Clean ll_s !_ I_ Engine Olt I_q=,: Air Filter _= N CleanAirScreen _2 IG InSpect Muffler/Spark Arre_ter Replace Oil Filter (if equip
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See =TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).
BATI'ERY TRANSAXLE Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
Air S__in _Oil _: Plug FillCap/ Dipstick CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. CLEAN AIR INTAKE/COOLING AREAS To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at air times.
_CAUTION: Before performing any service or adjustments: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
BottomEdge of Mower to Ground _ [_ BottomEdgeof Mowerto _ Ground BothFrontLinksShould be Equal in Length FRONT-TO-BACK ADJUSTMENT IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE, If the following front-toback adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the mower housing should be adjusted so the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.
Screws Idler Pulleys Electric Clutch Pulley Left Hand Cover Ddve Belt Left Mandrel Pdmaw IdlerArm Keepem TO REPLACE MOWER BLADE DRIVE BELT Park the tractor on level surface. Engage parking brake, • Remove mower drive belt (See "TO REPLACE MOWER DRIVE BELT" in this section of this manual), • Remove mower (See "TO REMOVE MOWER" in this section of this manual). • Remove screws from R.H. mandrel cover and remove cover. Unhook spring from bolt on mower housing, • Carefully roll belt off R.H. mandrel pulley.
Rotor BELTREMOVAL- Clutch Plate • Engage parkingbrake (creates slack in belt). • Remove belt from clutchingand fan idler pulleys. • Loosenpelt keeper above transaxle pulley. • Remove belt from transaxlepulley. • Remove belt from engine pulley and front V-idler pulley. • Pull belt out of all belt keepers and removefrom tractor. Slot < Nylon Locknut (31 TO ADJUST BRAKE Yourtractoris equippedwith an adjustable brake system whichis mountedon the right side of the transaxle.
TO ADJUST MOTION CONTROL LEVER The motion control lever has boon preset at the factory and adjustment should not be necessary. If for any reason the motion control lever will not hold its position while at a selected speed, it may be adjusted at the friction pack located on the right side of chassis. • Park tractor on level surface. Stop tractor by turning ignition key to "OFF" position and engage parking brake. • Place motion control lever in neutral (N) position.
REAR WHEEL • Blockrear axle securely. • Remove five (5) hub boltsto allow wheel removal, • Repair tire and reassemble. Replace and tighten hub boltssecurely. NOTE: To seal tire puncturesand preventflat tires due to slow leaks,tire sealant may be purchasedfrom your local partsdealer. Tire sealant also preventstire dry rot and corrosion. Washers osto,nin0 Axle \ I \ IIIll ((_'_ I|! TO START ENGINE WITH A WEAK BATFERY A, CAUTION: Lead-acid batteries generate explosive gases.
INTERLOCKS AND RELAYS Loose or damaged wiringmay cause yourtractorto runpoorly,stop running,or preventitfrom starting. • Check wiring. See electdcalwiring diagramin the Repair Parts section. TO REPLACE FUSE Replace with 30 amp automotive-type plug-infuse. The fuse holderis located behindthe dash. HeadlightWire Connector TO ADJUST ATTACHMENT LIFT SPRING ENGINE • While holding spring bushing with wrench, loosen jam nut.
TO ADJUST CHOKE CONTROL PRELIMINARY SETTING. The choke control has been preset at the factory and adjustment should not be necessary, chock adjustment as descdbed below before loosening cable. If adjustment is necessary, proceed as follows: • With engine not running, move choke control (located on dash panel) to full choke position. • Remove air cleaner cover, filter and cartridge plate to expose carburetor choke (See "A_R FILTER" in the Maintenance section of this manual). • Choke should be closed.
Immediatelyprepare yourtractorfor storageat the end of the season or if the tractorwillnot be used for 30 days or more. CAUTION: Never storethe tractor wuthgasolinein the tank inside a buildingwhere fumes may reach an open flameor spark. Allow the engine to cool beforestonngin any enclosure. TRACTOR Remove mowerfrom tractorfor winter storage. When moweris to be storedfor a penod of time, clean it thoroughly, removeall dirt,grease, leaves,etc. Store in a clean,dry area.
TROUBLESHOOTING )ROBLEM Will not start / : CHART CAUSE CORRECTION • Out of fuel. • Engine not "CHOKED" properly. • Engine flooded. • Fill fuel tank. • See "TO START ENGINE" in Operation section. • Wait several minutes before attempting to start. • Bad spark plug. • Replace spark plug. • Dirtyair filter. • Clean/replace air filter. • Dirtyfuel filter. • Replace fuel filter. • Water in fuel. • Drain fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Loss of power nontinued • Faultyspark plug. • Clean and rogap or change sparkplug. • Dirtyfuel filter. • Replacefuel filter. • Drain fuel tank and refillwith • Stale or dirtyfuel. fresh gasoline. • Water in fuel. • Drain fuel tank and carburetor, refilltank withfresh gasoline and replacefuel filter. • Spark plug wire loose. • Connectand tightenspark plugwire. • Dirtyengine air screen/fins. • Clean engine air screen/fins. • Dirty/cloggedmuffler.
I HUUI_I.P'_ItUU I INUGHART PROBLEM CAUSE • Worn, bent or loose blade. Poorgrass discharge (Contn) Buildup of grass, leaves, and trash under mower. Mower drive belt worn. Blades impropedy installed, Improperblades used. • Clogged mower deck vent holesfrom buildupof grass, leaves, and trash around mandrels. CORRECTION • Replace/sharpen blade. Tighten blade bolt, • Clean underside of mower housing. • Replace mower drive belt. • Reinstall blades sharp edge down. • Replace with blades listed in this manual.
TRACTOR - MODEL NUMBER 917.272960 SCHEMATIC AMMETER (OPTIONAL) I_ITE AED )B s G CLUTCH / BRAKE (PEDAL UP) L ........ RED GNITIOr SWITCk i PTO (DISENGAGED) e_ i SEAT SWITCH (NOT OCCUPIED] (OPTIONAL) A SPARKPLUGS ,aNmON _(2 UNIT J L G_S ON "P_NI N CYL. ENGINES) b FUEL SHUT.OFF SOLENOID REGULATO_ _ VOLTS ACe _ Pro OFF pOSITION ON IGNITION SWITCH RPMC_O_ATOAO_CC_e4EC1ED ) SWITCH _ HEADLIGHTS C+GrB*H CIRCUIT *FrB÷ErA+D RELAY OFF M*G.
TRACTOR -- MODEL NUMBER 917.
TRACTOR-- MODEL NUMBER 917.272960 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 2 8 10 11 12 16 21 22 24 25 26 27 28 29 30 33 40 41 42 43 45 50 52 79 81 Battery Bolt Hex Head 1/420 x 3/4 Tray, Battery Bo_t 1/4-20 x 7 5 Zinc Hold down Battery Cash Mount Nut Push Nylon 1/4" Switch Interlock Push-In Harness Socket Light W41523 Bulb Light Cable, Battery Cable, Battery Fuse Nut Keps Hex 1/4-20 Unc Cable,Ground Switch, Plunger Switch, Ign Key, Ignition Harness Ign.
I HA(.;1OR CHASSIS AND ENCLOSURES -- MODEL NUMBER 917.
TRACTOR - MODEL NUMBER 917.272960 CHASSIS AND ENCLOSURES KEY PART NO.
IHACTOR -- MODEL NUMBER GROUND DRIVE 40 917.
TRACTOR -- MODEL NUMBER 917,272960 GROUND DRIVE KEY NO, PART NO. DESCRIPTION 2 3 5 6 7 9 15 17 20 22 23 28 29 30 33 34 35 36 37 38 39 46 41 42 46 47 48 50 51 52 53 54 55 56 58 61 64 65 66 67 68 69 70 7070E 756.
I HAUTOH -- MODEL NUMBER 917.
STEERING TRACTOR --MODELNUMBER 917.272960 KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 25 26 27 28 29 3O 31 32 33 34 35 36 37 38 39 40 41 42 45 Wheel, Steering Axle Asm., Front Fitting, Grease Spindle Asm, LH Spindle Asm., RH Bearing, RaceThrust Harden Washer 25/32 x 1-5/8 x 16 Ga. Ring, Klip #T5304+75 Cap, Spindle Bolt, Fin Hex 5/8-11 x 2-3/4 Spacer Beadng Axle Front Nut, Lock Flange 5/8-11 Uric Washer 25/32 x 1-1/4 x 16 Ga.
I HAL; I UH -- MUUI:L NUMBER 917.272960 ENGINE 18 te 17 37 i ' _42 _ _ 43 29 \ 16 [ SPARK 4O KEY PART NO, NO. 1 2 5 7 8 9 10 11 12 15 16 17 18 19 161063 13200300 1513_6 121361X 15(_828 105432X 140923 143996 151346 10g_27X 106082X 140527 132903O0 20 21 22 24 25 26 27 28 29 164067 164863 164415 _1237 73920600 3645J 139277 7834R 13292O KEY PART NO. NO. DESCRIPTION Englne(SeeBreakdown) Kohler Model No.
TRACTOR -- MODEL NUMBER 917.272960 SEAT ASSEMBLY KEY NO. 1 2 3 4 5 6 7 8 10 12 13 PART NO. 140123 140551 140675 127018 145006 STD541437 124181X 171877 155925 121246X 121248X DESCRIPTION Seat Bracket, Pivot Seat Strap, Fender Bolt, Shoulder 5/16-18 x .62 Clip, PushIn, Hinged Nut,Crownlock 3/8-16 Uric Spring,SeatCprsn Bolt 5/16-t8 Unc x 3/4 w Sems Pan, Seat Bracket,MountingSwitch Bushing,Snap KEY PART NO. NO.
t rt_, iPM -- MUUI:I. I_IUMUI;H _17.272960 DECALS 17 17 7 22 1 14 --'-23 11 KEY NO, 1 2 PART NO, 164094 149518 3 4 5 6 7 8 9 10 11 12 171702 171703 146837 13,3644 171705 133179 163204 156439 4900J 146790 8 DESCRIPTION DecalDseh DecaJBatterj DNGWPSN ENGAsm DecalHood RH Craftsman Decal Hood LH Craftsman Decal Brake Parking Saddle DecalMalntenance Decal Side Panel Decal Housing Mower Decal FenderCraltsman DecalFender Danger Decal ClutclVBrake Decal V-Belt Dr Sch PART NO.
TRACTOR - MODEL NUMBER 917.272960 LIFT ASSEMBLY 6 12 16 13 23 22 12 13 19 '20 KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Rod Asm,, Lever Shaft Asm., Lift Vgt Lever Asm., Lift Rh E-RIngTruarc#5133-87 Washer 23/32 x 1-1/4 x 16 Ga, Boll, Fin Hex 3/8-16 x 1-1/2 Grip, Handle Fluted Button, Plunger Plunger, Button Spring 2-1/8" Link Lift Retainer, Spring Arm, Suspension Vgt Beadng Nut, Crownloek 3/8-16 Unc Spring Asm.
TRACTOR -- MODEL NUMBER 917.
TRACTOR - MODEL NUMBER 917.272960 MOWER DECK KEY NO. 1 3 5 6 PART NO.
TRACTOR - MODEL NUMBER 917.
TRACTOR - MODEL NUMBER 917.272960 TRANSAXLE--MODEL NUMBER 222-3010L K]EY pART NO. NO. 1 2 7 16 2O 21 22 33 35 36 37 38 39 4O 41 42 43 45 46 47 49 63 64 164591 164592 153765 142876 -142877 142878 142879 142929 142880 142882 142883 142884 142885 142886 142887 142888 142889 142890 142891 142892 153766 142894 150818 65 67 68 69 70 71 142897 142898 142899 142900 142901 142902 DESCRIPTION Assembly, Housing, LH Assembly, Housing, RH O11 Seal ,984 x 1.
TRACTOR - MODEL NUMBER 917.
TRACTOR - MODELNUMBER 917.272960 TRANSAXLE--MODEL NUMBER 222-3010L KEY NO. 1 2 3 4 5 6 8 12 13 14 15 17 19 21 22 23 25 32 37 38 42 43 44 47 53 60 62 63 64 67 -NOTE: pART NO.
1HACTOR -- MODEL NUMBER 917,272960 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65561 CYLINDER HEAD, VALVE AND BREATHER I \ 7m 4 i 29 CRANKCAEEJ 54
TRACTOR - MODEL NUMBER 917,272960 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65561 HEADNALVE/BREATHER CRANKCASE KEY PART NO. NO. KEY PART NO. NO.
TRACTOR - MODELNUMBER 917.
TRACTOR - MODEL NUMBER 917.272960 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65561 IGNITION/CHARGING KEY PART • NO. NO, 1 54-755-15-S 2 M-403025-S 3 4 5 6 7 X-25-92-S 24-112-04-S 25-086-47-S 24-157-03-S 12-086-14-S 8 g 10 11 12 13 12-468-03/S X-42-15-S24-025-04-S 25-403-03-S X-25-92-S 24-086-18-S 14 15 236602-S 54-755-09-S 16 17 12-132-06-S M-548025-S 18 19 20 21 22 235173-S 48-154-02-S X-25-63-S 24-584-01-S M-545020-S NOT ----*-- BLOWER HOUSING & BAFFLES KEY PART NO. NO.
TRACTOR - MODELNUMBER 917.272960 KOHLER ENGINE-MODEL NUMBER CV20S, TYPENUMBER 65561 STARTING SYSTEM I ENGINE CONTROLS S Q r 4 2 q S 16 OIL PAN / LUBRICATION I J ! I)-- • _'$ /1 _) $..
TRACTOR -- MODEL NUMBER 917.272960 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65561 OIL PAN/LUBRICATION STARTING SYSTEM KEY NO. PART NO. "_ M-839070-$ 2 3 24-O96-05-S M-839080-S 4 5 6 7 8 9 10 11 12-468-01-S 25-098-05-S 12-221-01-S 12-227-13-S 12-211-01-S 12-755-54-S 12-227-06-S 12-170-05-S DESCRIPTION Screw, hex. flange M8x1.25x70 Cover, inion Screw, _ex. flange MSxt .
I HAU I UH -- MUUP.
TRACTOR - MODEL NUMBER 917.272960 KOHLER ENGiNE-MODEL NUMBER CV20S, TYPE NUMBER 65561 CRANKSHAFT FUEL SYSTEM KEY PART NO. NO. DESCRIPTION 1 2 Crankshaft (Includes 2) Plug, cup 1 24-853-25-S 2 3 24-041-15-S 24-053-25 KEY PART NO, NO. DESCRIPTION 1 2 Gasket exhaust (2) Stud, M8xl.25x33 (4 4 5 6 7 8 9 10 24-041-t4-S M-629095-S M-641060-S 47-154-01-S 24-353-03-S X-426-9-S 24-086-12-S 24-014-72-S 52-139-09-S KEY PART NO. NO. EXHAUST 24-041-02-S 25-072-04-S NOTILLUSTRATED .
SUGGESTED GUIDE FOR SIGHTING SLOPES SIGHTING GUIDE I_ "_ FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL I greater than 15 °) never across the face. Make rums gredually to prevent tipping or loss of control. Exerc se extreme erate when your Tractor updirection and downonthe face of slopes (not i caution changing slopes.
Get it fixed, at your home or ours! For repair of major brand appliances In your own home,,, no matter who made it, no matter who sold it! 1-800-4-MY-HOME SMAoytir.e. day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime,day or night www.sears.
