MSDS

6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Remove all possible sources of ignition in the surrounding area. Many vapors are
heavier than air and will spread along ground and collect in low or confined areas (sewers,
basements, tanks). Wear appropriate protective equipment and clothing during clean-up. Avoid
breathing mist or vapor. Emergency personnel need self-contained breathing equipment. Do not
touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ventilate closed spaces before entering them. Use appropriate containment to avoid
environmental contamination. Local authorities should be advised if significant spillages cannot be
contained. For personal protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep
combustibles (wood, paper, oil, etc.) away from spilled material. This product is miscible in water.
Stop the flow of material, if this is without risk. Prevent product from entering drains. Wipe up with
absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Avoid
discharge into drains, water courses or onto the ground. Inform appropriate managerial or
supervisory personnel of all environmental releases. Use appropriate containment to avoid
environmental contamination.
Environmental precautions
7. Handling and storage
Minimize fire risks from flammable and combustible materials (including combustible dust and
static accumulating liquids) or dangerous reactions with incompatible materials. Pressurized
container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective.
Do not spray on a naked flame or any other incandescent material. Do not smoke while using or
until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to
heat, flame, sparks, or other sources of ignition. Use caution around energized equipment. The
metal container will conduct electricity if it contacts a live source. This may result in injury to the
user from electrical shock and/or flash fire. Avoid breathing mist or vapor. Avoid contact with eyes,
skin, and clothing. Avoid prolonged exposure. Use only in well-ventilated areas. Wear appropriate
personal protective equipment. Wash hands thoroughly after handling. Observe good industrial
hygiene practices. Avoid release to the environment. For product usage instructions, please see
the product label.
Precautions for safe handling
Level 3 Aerosol.
Pressurized container. Protect from sunlight and do not expose to temperatures exceeding
50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open flame,
heat or other sources of ignition. This material can accumulate static charge which may cause
spark and become an ignition source. Avoid spark promoters. These alone may be insufficient to
remove static electricity. Store in a well-ventilated place. Store away from incompatible materials
(see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
PEL 1800 mg/m3Propane (CAS 74-98-6)
1000 ppm
US. NIOSH: Pocket Guide to Chemical Hazards
ValueComponents Type
TWA 1800 mg/m3Propane (CAS 74-98-6)
1000 ppm
No biological exposure limits noted for the ingredient(s).
Biological limit values
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Eye
wash facilities and emergency shower must be available when handling this product.
Appropriate engineering
controls
Individual protection measures, such as personal protective equipment
Wear safety glasses with side shields (or goggles).
Eye/face protection
Skin protection
Wear protective gloves such as: Nitrile. Neoprene.
Hand protection
3 / 8
Material name: Red Grease
03079 Version #: 01 Issue date: 07-16-2015
SDS US