MSDS

Special protective equipment
and precautions for firefighters
Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Fire-fighting
equipment/instructions
In case of fire: Stop leak if safe to do so. Do not move cargo or vehicle if cargo has been exposed
to heat. Move containers from fire area if you can do so without risk. Containers should be cooled
with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose
holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.
General fire hazards
Extremely flammable aerosol.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Remove all possible sources of ignition in the surrounding area. Wear appropriate
personal protective equipment. Do not touch damaged containers or spilled material unless
wearing appropriate protective clothing. Avoid inhalation of vapors or mists. Avoid breathing gas.
Ventilate closed spaces before entering them. Use appropriate containment to avoid
environmental contamination. Transfer by mechanical means such as vacuum truck to a salvage
tank or other suitable container for recovery or safe disposal. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Methods and materials for
containment and cleaning up
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep
combustibles (wood, paper, oil, etc.) away from spilled material. This material is classified as a
water pollutant under the Clean Water Act and should be prevented from contaminating soil or
from entering sewage and drainage systems which lead to waterways. Stop leak if you can do so
without risk. Move the cylinder to a safe and open area if the leak is irreparable. Isolate area until
gas has dispersed. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand
or earth and place into containers.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination. For waste disposal, see section 13 of the SDS.
Environmental precautions
Avoid release to the environment. Contact local authorities in case of spillage to drain/aquatic
environment. Prevent further leakage or spillage if safe to do so. Do not contaminate water. Avoid
discharge into drains, water courses or onto the ground. Use appropriate containment to avoid
environmental contamination.
7. Handling and storage
Precautions for safe handling
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Minimize fire risks from flammable and combustible materials (including
combustible dust and static accumulating liquids) or dangerous reactions with incompatible
materials. Handling operations that can promote accumulation of static charges include but are not
limited to: mixing, filtering, pumping at high flow rates, splash filling, creating mists or sprays, tank
and container filling, tank cleaning, sampling, gauging, switch loading, vacuum truck operations.
Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing
or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
expose containers to heat, flame, sparks, or other sources of ignition. Do not re-use empty
containers. Avoid breathing mist or vapor. Avoid breathing gas. Avoid contact with skin. Avoid
contact with eyes. Avoid contact during pregnancy/while nursing. Avoid prolonged exposure. Avoid
contact with clothing. Use only in well-ventilated areas. Wear appropriate personal protective
equipment. Observe good industrial hygiene practices. When using, do not eat, drink or smoke.
Wash hands thoroughly after handling. Use caution around energized equipment. The metal
container will conduct electricity if it contacts a live source. This may result in injury to the user
from electrical shock and/or flash fire. Avoid release to the environment. Do not empty into drains.
For product usage instructions, please see the product label.
Conditions for safe storage,
including any incompatibilities
Level 3 Aerosol.
Pressurized container. Protect from sunlight and do not expose to temperatures exceeding
50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open flame,
heat or other sources of ignition. This material can accumulate static charge which may cause
spark and become an ignition source. Avoid spark promoters. These alone may be insufficient to
remove static electricity. Store in a well-ventilated place. Store away from incompatible materials
(see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents
Form
Type
PEL 5 mg/m3 Mist.Distillates (petroleum),
Solvent-refined Heavy
Paraffinic (CAS
64741-88-4)
2000 mg/m3
500 ppm
3 / 10
Material name: Battery Terminal Protector
1808 Version #: 02 Revision date: 10-30-2013 Issue date: 10-21-2013
SDS US