3D Printer Quick Installation Guide Ender-3 S1 For a better experience in using our product, you can also learn how to use the Printer in the following ways: View the accompanied instructions and videos in the Storage card. V1.
1 Notes 1 Do not use the printer any way other than described herein in order to avoid personal injury or property damage. 2 Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment. 3 Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
17 Hexagon socket head 18 Hexagon socket flat spring washer combination screw M5x45 X5 round head screw M4x18 X4 19 Hexagon socket head cap screw M3x6 X5 20 Z-axis limit switch kit x1 Tips: the above accessories are for reference only, in kind prevail! 4 Interface Descriptions 4.
5 Product installation 5.1 Nozzle assembly and wire clamp installation A. Place the nozzle assembly on the mounting back panel of the extruder, pre-lock with four M3x6 hexagon socket head cap screw, and then tighten to fix it. B. Clip the wire clamp to the back panel of the X-axis motor. 3 5 19 3 2 5.2 Gantry frame installation A. Move the right profile of the bottom component out of the desktop about 35mm, and expose the installation holes. B.
.3 Display installation A. Place the display bracket on the side of the right profile, and tighten it with three M4X18 hexagon flat round head screws. B. Align the pins on the back of the display with the large holes of the display bracket and insert them, and then slide down to tighten it. 6 7 18 5.4 Material rack installation A. Find the material pipe accessories, and fix the threaded end on the right end of the material rack. B.
1. Connect the nozzle to the 24pin port as shown in the figure. 2. Connect the X and Z axis stepper motors according to the yellow label on 6pin (4 wires) port. 3. Connect the X-axis limit switch as indicated by the yellow label on the 3pin (2 wires) port. 4. Connect 3pin (3 wires) 2.0 port to the keysets, and 3pin (3 wires) 2.54 port to the filament detector.
the inclination of the printing platform is larger than 2mm, CR-Touch leveling will fail. 7 Auxiliary leveling （When Please use the auxiliary leveling） 1. Enter “Control → Reset configuration” to reset the printer parameters. 2. Enter “Prepare→ Auto Home” and return to the starting position. 3. Enter “Prepare → Move → Move Z”, and clear the value. 4. Enter “Prepare→Z-offset”, adjust the Z-axis compensation value so that the height from the nozzle to the platform is almost the thickness of A4 paper (0.
5.Enter “Prepare → Disable stepper” to turn off all enabled motors. 6. Adjust the knob at the bottom of the hot bed, move the nozzle to the four corners of the printing platform, so that the height of the nozzle to the printing platform is almost the thickness of A4 paper (0.08-0.1mm) to ensure that the four corners are leveled. The nozzle is so far away from the platform that the filaments can’t attach to the platform. Extrude the filaments evenly to make them attach to the platform properly.
8 Load Filaments A. In order to complete the loading smoothly, please trim the end of the filaments to an inclination of 45°. B. First pass the filament through the filament detector hole, then press the handle of the extruder, and insert the filament along the extruder hole until the nozzle position. C.Preheat the nozzle. When the temperature reaches the set value, you can see that there are filaments flowing out of the nozzle, and the loading is completed. Replace filaments： 1.
3. Select Printer (Ender-3 S1) 4. Enter the corresponding parameters → Close Load Creality Slicer 5. Open Creality Slicer 6. Load File 7. Select File 8. Generate G code → Save to memory card It is important to note file name within the memory card must be in Latin letters or numbers. Chinese characters or any other special symbol cannot be displayed by the printer. 9. Insert Memory Card User the screen knob to select the menu Select the desire print file.
10 Equipment Introduction 8 9 1 2 3 10 4 5 6 19 20 21 11 7 1 X-axis Limit Switch 9 2 Nozzle Assembly 10 X-axis Belt Tension Adjustment Knob Filament Sensor 17 Y-axis Belt Tension Adjustment Knob 3 Auto Leveling Assembly 11 Display 18 Coupler 4 Printing Platform 12 Z-axis Motor Z2 19 Z-axis Motor Z1 5 Memory Card Slot 13 Y-Axis Limit Switch 20 Power Switch 6 Type-C Connection 14 Voltage Toggle Switch 21 Power Socket 7 Tool Box 15 Y-axis Motor 8 Spool Holder 16 X-axis Motor The ac
