CR-10 Smart 创造现实，成就梦想 Create reality，achieve dreams CR-10 Smart 3D Printer User Manual 3D打印机用户使用手册 V1.
Dear Consumers, Thank you for choosing our products.For the best experience,please read the instructions before operating the Printer. Our teams wiss always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you can also learn how to use the printer in the following ways: View the accompanied instructions and videos in the TF Card.
NOTES 使用须知 1 Do not use the printer any way other than described herein in order to avoid personal injury or property damage. 2 Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment. 3 Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality. 4 Please use recommended resin to in case damage of machine.
Contents目录 Introduction 设备简介 01-01 Parameters 设备参数 02-02 Parts List 零部件清单 03-03 Assemble the 3D Printer 组装3D打印机 04-08 Use the 3D Printer 使用3D打印机 09-13 Wifi Printing Wifi 打印 14-16 Start Printing 首次打印 17-19 Wiring Connection电路接线 20-20 Troubleshooting 故障检修 21-22 FDM 3D PRINTING FILAMENTS 3D打印耗材 23-28 Warranty Card 保修卡 29-31
1.
2.
3.
4. Install the Gantry Frame 安装龙门架 1 Base Frame｜底座 x 1 2 9 Gantry Frame｜龙门架 x 1 M5x45 Sems Screw ×4 M5x45组合螺丝 2 1 9 9 Two Z-axis profiles, installed on the inner step of the Y-axis bottom profile. 两根Z轴型材，靠Y轴底部型材内侧台阶安装。 Twist the coupling to raise the X axis to the position as picture shown.
5.
6. Install the Rack 安装料架 12 15 5 Rack｜料架 x 1 6 Spool｜料管 x 1 12 M5x10 Hexagon flat round head screws x2 M5x10内六角平圆头螺丝 15 M4T Nut ×2 M4T型螺母 6 Y-axis bottom profile Y轴底部型材 5 The material rack can be installed in different positions on the front and back of the Z axis, and can be folded.
7. Install Limit switch for Z axis 安装Z轴限位开关 Easier to replace the platform and adjust the belt 更换平台更容易，调节皮带更方便 A 1.Rotate the glass pick-and-place handleplate for platform replacement. 1.转动玻璃取放手柄压板可进行平台更换。 2.Then manually turn the knob to the appropriate tightness to avoid belt breakage. (as shown in figure A, three places) 2.
8. Cable Connection 设备接线 Cable Connection 设备接线 1 Connect the 15pin port to the nozzle adapter board as shown in the figure 2 Connect Z-axis motor cable 连接Z轴电机线 按图示15pin端口连接喷头转接板 3 Connect the photoelectric switch wire 连接光电开关线 4 Connect the power cord 连接电源线 Caution ●Do not connect or disconnect the cables when the machine is powered on.
9. Bed Leveling 调平平台 1. Slelct“Level”to automatically level 选择首页调平，即可自动调平 2. After the leveling is completed,adjust the Z-axis compensation value according to the adhesion of the printing consumables and the glass 调平完成后，依据打印耗材与玻璃平台的粘附情况，适当调节Z轴补偿值 >> >> >> >> During the leveling process,please do not touch the Teflon tube and nozzle cable.
10. Preheating Method 预热方法 Method 1 方法1 >> >> Notes: The UI information is only for reference,the actual UI may be different.
10. Preheating Method 预热方法 Method 2 >> >> >> >> 方法2 Notes: The print preheating standard is adjusted at the factory, PLA preheating standard: nozzle temperature 200 °, hot bed temperature 60 °, ABS preheating standard: nozzle temperature 240 °, hot bed temperature 70 °.If you need to adjust it due to printing materials or other reasons, you can adjust the parameters on the interface home page control → temperature → PLA / ABS preheat setting.
11. Load Filament 装料 When you wait for the temperature to rise,hang the filament over the Filament Holder. 当您等待温度上升时，把耗材挂在料架上。 For loading filament smoothly,the end of the filament should be placed as shown above.
11. Load Filament 装料 Whe the current temperature reaches the target temperature,the consumables pass the material breakage detection,and are inserted into the small hole of the extruder until the position of the nozzle,If the consumables flow out at the nozzle,it means that the consumables have been loaded. Method of adjusting the tightness of the extrusion spring:Arrow to right is tightening,arrow to left is lossen.
12. WiFi Printing WiFi 打印 >> 1.Download 1.下载 >> 2.Register 2.注册 >> 5.Add equipment 5.新增设备 >> >> 6. Setting 6.设置 4. Scan QR Code 4.扫一扫 3.Log in 3.登录 >> 7.Connect WiFi 7.连接WIFI 8.Select print model 8.
12. 11. WiFi StartPrinting Printing WiFi 开始打印 打印 >> >> Notes: The UI information is only for reference,the actual UI may be different.
12. 11.
13. Start Printing 开始打印 >> >> 3. Select language→Next→Select your machine→Next→Finish. >> >> 1. Double click to install the software. | 安装软件 4.Open Creality 3D slicer → Load（Read file) → Select file. 打开创想三维切片软件→Load（读取文件）→选择文件。 2、Double click to open the software. | 打开软件 17 3.依次选择语言→Next→选择对应机型→Next→Finish,完成设置.
13. Start Printing 开始打印 >> 6.Insert the storage card→ Click print 5.Generate G-code，and save the gcode file to storage card. 生成 G 代码→保存到存储卡 File names must be Latin letters or numbers, not Chinese characters or other special symbols 文件名需为拉丁字母或数字，不能为汉字或其他特殊符号 control→ Select the file to be printed.
13.
14.
15.
15.
16. FDM 3D PRINTING FILAMENTS Upgraded environmentally friendly formula, matte effect, high toughness, and fine printing. The raw materials are imported from the United States, besides, there are rich colors for customers to choose. Standard Resin FDM 3D PRINTING FILAMENTS Targeting at mid-end users, CR series is with transparent tray plus black-white color box design. lts slight tolerance in wire diameter contributes to stable printing quality.
17.
21. Filaments 18.
19.
20.光敏树脂种类参数信息 相关参数 类ABS树脂 可铸造牙冠树脂 压模树脂 可铸造首饰树脂 355nm-410nm 355nm-410nm 355nm-410nm 355nm-410nm 355nm-410nm 1.05-1.25g/cm³ (密度计(25℃)) 1.05-1.25g/cm³ (密度计(25℃)) 1.05-1.25g/cm³ (密度计(25℃)) 1.05-1.13g/cm³ (密度计(25℃)) 1.882-2.385Mpa 1.882-2.385Mpa 1.882-2.385Mpa 1.882-2.385Mpa 1.192-2.525Mpa 40-70MPa 40-70MPa 59-70MPa 40-70MPa 59-70MPa 49-58MPa 75℃ 80℃ 80℃ 80℃ 80℃ 220℃ 65℃ 95*E-6 95*E-6 95*E-6 95*E-6 95*E-6 95*E-6 95*E-6 95*E-6 3.72-4.24% 3.72-4.24% 1.88-2.45% 3.72-4.
21.
22.
售后服务卡 30
售后服务卡 31
SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD. Add:18F,JinXiuHongDu Building, Meilong Blvd., Longhua Dist., Shenzhen, China 518131 Official Website: www.creality.com Tel：+86 755-8523 4565 E-mail: info@creality.com cs@creality.com Scan To Learn More 更多服务请关注公众号 深圳市龙华区民治街道新牛社区梅龙大道锦绣鸿都大厦18F 公司网站：www.cxsw3d.
