Remote Starter User Manual

ManualsBrandsCrimestopper Security Products ManualsRemote StarterEZ-90

EZ-90 / EZ-91

REMOTE ENGINE STARTING SYSTEM

OPERATING INSTRUCTIONS

INTRODUCTION

**IMPORTANT NOTES:- FOR EZ-91 MODEL ONLY**

The EZ-91 model is an add-on (expansion unit), without remotes or antenna. It must be controlled by an existing

alarm or keyless entry system (host system). The “Infinity Run” feature is not available on an EZ-91 system. Most

of the other standard remote starting features of this system can be controlled through the existing remote of the

host system. For most applications, remote start is triggered by pressing a Factory remote’s Lock button 3 times

or pressing an Auxiliary channel button on an Aftermarket system. This is referred to in this manual as activating

the “Green Start input wire”.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote

Start connections, Flashing lights, Brake Reset. For programming, the hood pin and program button are required.

-OPTIONAL: These are features to be connected only if desired or agreed upon by the customer and the

installing dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc. These features

may also require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is

going to be installed with your particular system.

TECHNICAL SUPPORT: (800) 998-6880

This device complies with FCC Rules part 15. Operation is

subject to the following two conditions: 1) This device may not

cause interference, and (2) this device must accept any

interference that may be received, including interference that

may cause undesired operation. The manufacturer is not

responsible for any radio or TV interference caused by

unauthorized modification to this equipment. Such modification

could void the user's authority to operate the equipment.

Monday - Friday 8:00am - 4:30pm Pacific Std. Time

Web Site: www.crimestopper.com

E-mail: email@crimestopper.com

CRIMESTOPPER SECURITY PRODUCTS, INC.

1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV A - 08.2004

Summary of content (12 pages)

PAGE 1
EZ-90 / EZ-91 REMOTE ENGINE STARTING SYSTEM OPERATING INSTRUCTIONS INTRODUCTION **IMPORTANT NOTES:- FOR EZ-91 MODEL ONLY** The EZ-91 model is an add-on (expansion unit), without remotes or antenna. It must be controlled by an existing alarm or keyless entry system (host system). The “Infinity Run” feature is not available on an EZ-91 system. Most of the other standard remote starting features of this system can be controlled through the existing remote of the host system.
PAGE 2
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………………………2 Using the Remote Transmitter…………………………………………………………………………………...…….3 Remote Engine Control…………….…..…………………………………………………………………….……….3-6 Turbo Timer Mode……………………………….……………………………………...………………………………7 Convenience and Safety Features……………………………….……………………………………...……..……8-9 Transmitter Programming….…………….…………………………………………….…………………………....…10 2 Vehicle Operation.…………………………………….………………...……………………..…………….
PAGE 3
USING THE REMOTE TRANSMITTER The transmitter supplied with the EZ-90 system has six buttons. The button configuration of the EZ-90 is Factory-set and unchangeable. The EZ-91 model does not include remote transmitters, as it is designed for the expansion of a “parent” remote keyless or alarm system. See Page 11 for additional information on how to use your remote to operate a second vehicle equipped with an EZ-90 system.
PAGE 4
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of up to10 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 10 seconds to help prevent damage to the starter from over cranking.
PAGE 5
REMOTE ENGINE CONTROL IDLE DOWN MODE - EXITING THE VEHICLE: 1) With vehicle engine running with key, press the Remote Start button for at least one second. (For EZ-91 model activate Green remote start input wire.) 2) Parking Lights will turn ON. 3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released. 4) Turn OFF Ignition and remove key. Engine should remain running. 5) Exit vehicle then remote lock doors if desired.
PAGE 6
REMOTE ENGINE CONTROL INFINITY RUN MODE – EXITING THE VEHICLE: 1) With vehicle engine running with the key, press the Remote Start button for at least 1 second, pause a few seconds, then press and release the remote start button a second time. 2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.
PAGE 7
TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the EZEE system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. Check with your installer about adding this feature.
PAGE 8
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock.
PAGE 9
CONVENIENCE AND SAFETY FEATURES VALET MODE / STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid and the system is now in valet. Perform this procedure again to exit of Valet mode.
PAGE 10
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The EZ-90 learns up to 4 different transmitter codes. 1. 2. 3. 4. Open Hood (If no hood pin installed with your system, then you must ground the Gray Hood pin wire). Turn key to the ON position. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. Press button #1 of the transmitter to be coded.
PAGE 11
2-VEHICLE OPERATION A single EZ-90 remote can control a second vehicle with an EZEE Start EZ-90 system installed. SETUP: Follow the “Transmitter Programming” steps on the second vehicle. Program Car #2’s existing remotes, then quickly press the Car #2 side button on your remote before pressing the Lock button on your remote to program it to Car #2.
PAGE 12
TROUBLESHOOTING cont. UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: • In extreme cold or severe weather conditions, the unit may take more than the first attempt to start the vehicle. The remote start unit will make up to 3 attempts to start the engine. • In some vehicles, there may be a Factory anti-theft system that will not allow the engine to run without the key in the ignition. These systems may include Factory Security Modules, GM Passkey®/Passlock®, and RF Transponder systems (Ford P.A.T.S.®).