PART LIST Top Panel Left Panel Bottom Panel Shelf Panel 1PC 1PC 1PC 1PC 1PC F | J Middle Shelf Upper Middle Left Middle Right Middle Front Panel Panel Panel Panel Panel 1PC 1PC 1PC 1PC 1PC Adjustable Shelf | Left Door Panel | Right Door Panel| Drawer Front |Drawer Left Panel Panel PCs 1PC 1PC PCS PCS Drawer Right Drawer Back Drawer Bottom | Left Back Panel Middle Back Panel Panel Panel Panel PCS PCS PCS 1PC 1PC uU Right Back Panel 1PC
HARDWARE LIST Boone $1/4" $8x30mm $ax1" Bolt Spring Washer Flat Washer Wood Dowel Long Screw 33 PCS (Extra 1) | 23 PCS (Extra 1) | 23 PCS (Extra 1) 34 PCS 16 PCS (Extra $3x14mm $3x14mm Magnet Round Head Shelf Holder Screw Handle Screw 2 PCS 4 PCS 8 PCS (Extra 1) |40 PCS (Extra 1) 4 PCS $5/32x19mm Round Head Allen Wrench | Safety Strap Kit Bolt 8 PCS 1PC 1 SET ADDITIONAL TOOLS (Not Provided) Note: It is not recommended to use power tools during assembly.
Step 1. Attach handles (part #10) to door panels (parts L & M) using round head bolts (part #11) and fillips head screwdriver. Attach magnets {part #8) to shelf panel (part E) using round head screws (part #7) and fillips head screwdriver. #10™yX Step 2. Attach drawer panels (parts drawer back panel (part Q) using long screws (part #5) and fillips head screwdriver.
Step 3. Attach front panel (part J) to bottom panel (part D) using wood dowels (part #4), bolts (part #1), spring washers (part #2), flat washers (part #3) and Allen wrench (part #12). Step 4. Attach upper middle panel (part G) to shelf panel (part E) using wood dowels (part #4), bolts (part #1), and Allen wrench (part #12).
Step 5. Attach middle panels (parts middle shelf panel (part F) using wood dowels (part #4), bolts (part #1), and Allen wrench (part #12). #1 mem Step 6. Attach assembled unit (parts bottom panel (part D) using wood dowels (part #4), bolts (part #1), spring washers (part #2), flat washers (part #3) and Allen wrench (part #12).
Step 7. Attach shelf panel (part E) to assembled unit (parts H & I) using wood dowels (part #4), bolts (part #1), and Allen wrench (part #12). #1 owes 1X1 Step 8. Attach panels (parts assembled unit (parts D & E) using wood dowels (part #4), bolts (part #1), spring washers (part #2), flat washers (part #3) and Allen wrench (part #12).
Step 9. Carefully turn unit upright. Attach top panel (part A) to assembled unit (parts using wood dowels (part #4), bolts (part #1), spring washers (part #2), flat washers (part #3) and Allen wrench (part #12). #12 x1 Step 10. Attach back panels (parts assembled unit (parts using screws (part #9) and fillips head screwdriver.
Step 13. Attach door panels (parts placing bottom pin hinge (preinstalled in door) in the per-drilled hole of bottom panel (part D). Then depress the top spring-loaded pin hinge so it can be placed in the per-drilled hole of shelf panel (part E). Note: Be sure top and bottom pin hinges are fully extended to secure doors in place. Note: It is important to adjust levelers once fully assembled and upright. Extend adjustable leveler until it's firmly in contact with the floor.
5/8"x #3xD8 $4xD8 Safety Strap | Wall Anchor Bracket Short Screw | Long Screw | Safety Wall Kit Strap 18ET 1PC PCS 1PC 1PC 1PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping, damage and/or injury. 1. Insert short screw (C) and safety wall strap (E) through bracket (B) and attach to top panel (part A} using fillips head screwdriver. 2. Drill a 11/32" hole where you want to secure the unit.