PART LIST (Ships Separately) Left Panel Right Panel Top Panel Front Middle Rail Front Top Rail 1PC 1PC 1PC 1PC 1PC Back Rail Back Panel Back Vertical Rail Bottom Panel Left Door Panel PCS PCS 1PC 1PC 1PC Right Door Panel Adjustable Shelf | Drawer Front Panel | Drawer Left Panel | Drawer Right Panel 1PC 1PC 1PC 1PC 1PC Drawer Back Panel Drawer Bottom Pane| Locking Caster Caster Towel Bar 1PC 1PC PCS PCS PCS
HARDWARE LIST Cam Lock Cam Bolt Wood Dowel Allen Bolt 12 PCS (Extra 2) 12 PCS 16 PCS 4 PCS € Short Allen Bolt Screw Barre! Nut Shelf Holder 4 PCS 8 PCS (Extra 1) 4 PCS 4 PCS Knob Round Head Bolt Large Round Head Screw| Double Magnet PCS PCS 16 PCS (Extra 1) 1PC #13 #14 Round Head Screw Allen Wrench 2 PCS (Extra 1) 1PC ADDITIONAL TOOLS (Not Provided) Note: It is not recommended to use power tools during assembly. Phillips Head Screwdriver Note: Wood dowels are intended for alignment.
Step 1. Insert cam bolts (part #2) into left panel (part A), right panel {part B) and top panel (part C) using fillips head screwdriver. NOTE: Do not over tighten cam bolts. Stop tightening once threads on cam bolt are no longer visible. #2 & x12 Step 2. Attach rails (parts right panel {part B) using cam locks (part #1) and wood dowels (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 3. Attach back vertical rail {part H) to back rail (part F) using wood dowels (part #3). Slide back panels (part G} into grooves of assembled unit (parts Step 4. Attach back rail (part F) to assembled unit (parts using cam lock (part #1) and wood dowels (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 5. Attach left panel (part A) to assembled unit (parts using cam locks (part #1) and wood dowels (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert. Step 6. Carefully turn unit upside down on a soft flat surface, such as carpet, as shown below. Attach bottom panel (part |) to assembled unit (parts using wood dowels (part #3), Allen bolts (part #4), barrel nuts (part #7) and Allen wrench (part #14).
Step 7. CASTER INSTALLATION Attach locking casters (part R) and casters (part S) to bottom pane! (part I) using large round head screws {part #11) and fillips head screwdriver. LEG INSTALLATION Do not install casters. Attach legs using instruction manual and hardware included inside leg packaging. #1 ¥ x6 Step 8. Carefully turn unit upright. Attach towel bars (part T) to panels (parts A & B) using short Allen bolts (part #5) and Allen wrench (part #14).
Step 9. Attach top panel (part C) to assembled unit (parts using cam locks (part #1) and wood dowel (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert. J colorants Step 10. Attach knobs (part #9) to door panels (parts J & K} using round head bolts (part #10) and fillips head screwdriver. Attach door panels (parts placing bottom pin hinge (per-installed in door) in the per-drilled hole of bottom panel (part 1).
Step 11. Attach knob (part #9) to drawer front panel (part M) using round head bolt (part #10) and fillips head screwdriver. Attach drawer panels (parts drawer front panel (part M) using screws (part #6) and fillips head screwdriver. Slide drawer bottom pane! (part Q) into grooves of assembled unit (parts Attach drawer back panel (part P) to assembled unit (parts using screws (part #6) and fillips head screwdriver. NOTE: Be sure drawer glide wheels are facing back panel. #8 Sug Step 12.