Datasheet

Document NO.: WI-FHF- CS-PME2SL -A
Page 7of 9
MODEL: CS-PME2SL
REV : A/2
Date : 18 Aug 2015
8
Vibration Proof
Capability
抗振动性能
After standard charged, keep for 0.5h~1h, then
installed onto the vibration test with clamps.
Equipment parameters of frequency and amplitude
are as follows(the frequency is to be varied at the
rate of 1oct/min between 10Hz～55Hz, and repeat
vibration for 30min. The battery is to be tested in
three mutually perpendicular directions):
frequency:10Hz～30Hz amplitude: 0.38mm
frequency:30Hz～55Hz amplitude: 0.19mm
电池按标准充满电后，搁置 0.5～1 小时。然后将电池
用夹具固定在振动台的台面上，按下面的振动频率和
对应的振幅调整好实验设备。X、Y、Z 三个方向每个
方向上从 10Hz～55Hz 循环扫频振动 30min，扫频速
率为 1 oct/min:
振动频率：10Hz～30Hz 位移幅值（单振幅）：0.38mm
振动频率：30Hz～55Hz 位移幅值（单振幅）：0.19mm
1) Battery appearance should not be
obvious nick, leak, smoke and
burst.电池外观应无明显损伤、漏液、
冒烟或爆炸。
2) After test, no defect in electrical
performance, and voltage≥3.7V.
实验后,电池插入相应机型接触良
好，且电池端电压应≥3.7V。
9
Fall Proof Capability
抗跌落性能
After complete charge, the battery is to be drop to a
armor plate(18mm～20mm thick) placed on a
cement floor from a height of 1.2 meter for 14
times.(fall down by six sides and one corner).
将充满电的电池由高度 1.2 米的位置自由跌落在
18mm～20mm 厚的钢板上，一共跌落 14 次（六个面
每个面跌落一次，另加跌一角，共两个循环）。
1) Battery should not be leak, smoke
and burst.
电池应不漏液、不冒烟、不爆炸。
2) After test, no defect in electrical
performance, and voltage≥3.7V.
实验后,电池插入相应机型接触良
好，且电池端电压应≥3.7V。
10
Capacity Retention
荷电保持能力
1) In environmental temperature 20℃±5℃
condition, Use nominal capacity charging
method full charge the battery.
在环境温度 20℃±5℃条件下, 按标称容量充电方
法将电池充饱电。
2) Lay the battery opened circuit 28 days, then use
0.2C discharge it to cut off voltage.
将电池开路搁置 28 天,再以 0.2C 放电至终止电
压。
0.2C discharging time should not less
than 90%.
0.2C 放电时间应不低于 90%.
11
Constant Temperature
and Humidity Proof
Capability
抗恒定湿热性能
After standard charged, keep for 0.5h～1h,then Lay
the battery in temperature 40±2 and humidity 90%
～95% environmental chambers for 60 hours. Then
lay the battery in environmental temperature 20±5
condition for 2 hours. Later discharge it in 0.2C and
record the capacity.
电池在标准充电后，搁置 0.5 小时～1 小时，然后将电
池放入 40℃±2℃，相对湿度为 90%～95%的恒温恒
湿箱中搁置 60 小时后，将电池取出在环境温度 20℃±5
℃的条件下搁置 2h，以 0.2C 放电，并记录容量。
1) Battery appearance should not be
obvious nick, leak, smoke and
burst.电池外观应无明显变形锈蚀、
冒烟或爆炸。
2) 0.2C discharging capacity should
not less than 80%.
0.2C 放电容量应≥80%。
3.4. Shipping Voltage (Inspection before shipment): ≥3.7V
出货空载电压(出货前检测): ≥3.7V