To The Owner • Assembly & Set-Up • Controls • Operation • Maintenance • Parts List Operator’s Manual Two-Stage Snow Thrower Attachment — 19A-126-100 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No.
1 To The Owner Thank You Thank you for purchasing a snow thrower attachment manufactured by Cub Cadet LLC. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.
8. 4. Do not operate machine while under the influence of alcohol or drugs. 5. Muffler and engine become hot and can cause a burn. Do not touch. 6. Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic. Do not carry passengers. 7. Exercise caution when changing direction and while operating on slopes. 8. Do not clear snow across the face of slopes; go up and down. Exercise extreme caution when operating on slopes.
Clearing A Clogged Discharge Chute Maintenance And Storage Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. 1. Never tamper with safety devices. Check their proper operation regularly. 2. Disengage power take-off, lower the attachment, set the parking brake, stop engine and remove key to prevent unintended starting.
3 Assembly & Set-Up Contents of Carton • One Auger Housing Assembly • One Upper Chute Crank Rod • Operator’s Manual • One Lift Handle Assembly • Two steering Linkage Covers • Two Self-adhesive Reflectors • One Hardware Pack Contents of Hardware Pack • Two Quick Release Pins (714-04061) • Extension Spring (732-04237) • Two Shoulder Bolts (738-0143) • Five Cable Ties (725-0157) • Extension Spring (932-0594A) • Two Lock Nuts (912-3000) WARNING! Before installing attachment, place tra
IMPORTANT: Use a second person to assist you or a hydraulic floor lift to complete steps 3 through 6. 3. Place the undercarriage assembly beneath the tractor and lift it up against the frame of the tractor. See Fig. 3-3. Attaching Chute Directional Control 1. Attach the chute directional control assembly to the upper lift link on the left side of the auger housing. Assemble with two hex screws and two saddle washers as illustrated in Fig. 3-5. Secure with two flange nuts.
Attaching The Lift Handle 1. 3. Disengage the brake and release the hydrostatic bypass rods (see your tractor’s owner’s manual for location of bypass rods) and carefully move the tractor forward (by pushing, NOT driving it) so that support tubes found on the rear of the auger housing assembly are positioned between the tractor’s front tires. Set the parking brake. 4. With the help of an assistant, lift up the auger housing and move it so that it rests over the shoulder bolts found on tractor See Fig.
Attaching Support Tubes Install Steering Covers 1. 1. Secure the left support tube to the front of the undercarriage assembly with the clevis pin and hairpin clip removed earlier. See Fig. 3-11. Install the two new steering mechanism covers as seen in Fig. 3-12 using the 3 screws removed earlier. Figure 3-12 Figure 3-11 Note: To help in lining up the support tube with the mounting hole it may be necessary to push up and down on the auger lift handle slightly. 2.
Set-Up Lift Adjustment WARNING! Never attempt to make any adjustments while the engine is running, except where specified in the Operator’s Manual. Place tractor on a firm and level surface. Place the PTO in the disengaged (OFF) position, set the parking brake, shut engine off, and remove key to prevent unintended starting. Shear Pins A pair of replacement auger shear pins and bow tie cotter pins are included with your snow thrower. Store them in a safe place until needed.
Lower Chute Crank Support Bracket Adjustment If the spiral at the base of the lower chute crank isn’t fully engaging with the notches in the lower chute assembly, the support bracket can be adjusted inward or outward as follows: 1. Loosen, but do NOT remove the two hex nuts which secure the support bracket to the snow thrower housing. See Fig. 3-16. Spiral Hex Nuts Support Bracket Figure 3-16 2.
4 Controls Trigger Control Chute Directional Control Lift Handle Figure 4-1 Chute Directional Control (See Fig. 4-1) Controls WARNING! Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly. Lift Handle (See Fig. 4-1) The lift handle is located on the right side of the tractor and is used to raise and lower the snow thrower attachment. 12 1.
5 Operation Operation 14. WARNING! Read, understand, and follow all instructions and warnings on the tractor, the attachment, and in the operator’s manuals before operating. Your snow thrower attachment is capable of displacing snow and clearing a path a width of 42 inches. Observe the following operating instructions for efficient snow removal: 1.
Replacing Shear Pins Tire Chain Kit The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. If the augers will not turn, check to see if the pins have sheared. See Fig. 5-1. • 20” x 8.
6 Maintenance WARNING: Before lubricating, repairing, or inspecting, place tractor on a firm and level surface. Place the PTO in the disengaged (OFF) position, set the parking brake, shut engine off, and remove key to prevent unintended starting. Lubrication of Chute Directional Control The spiral on the end of the lower chute crank, the base of the discharge chute itself and the joint blocks which connect the lower and upper chute cranks should be lubed with multipurpose automotive grease once a season.
Model 19A-126-100 52 56 61 58 47 55 15 46 52 63 3 59 42 54 50 60 45 53 49 51 43 59 62 44 48 16 52 57 8 A 9 51 2 16 8 63 20 15 19 16 14 6 6 7 41 23 40 6 35 30 25 27 33 24 21 64 1 36 31 40 29 26 28 37 34 A 7 63 4 18 12 5 11 18 13 16 32 38 39 18 5 10 5 21 17 22 63
Model 19A-126-100 Ref No. Part Number 1 918-04315 Description Auger Gear Box (Incl. Ref. 23-41) Ref No. Part Number 33 721-0325 Description Grease Plug 2 684-0158-0637 Impeller Assembly, 12” 34 721-0327 Grease Seal 3 684-0148-0637 Housing Assembly 35 936-0351 Flat Washer, .76 x 1.5 x .030 4 703-2734-0637 Housing Brace Bracket 36 936-0369 Flat Washer, .508 x 1.0 x .020 5 684-04163-0637 LH Spiral Auger 37 736-0617 Thrust Washer, .75 x 1.25 x .
Model 19A-126-100 52 62 1 55 16 17 60 54 61 26 53 19 4 11 83 12 7 27 51 7 10 104 11 4 4 59 50 3 56 4 29 5 8 4 57 58 6 2 75 97 20 89 103 76 22 99 4 78 18 15 67 91 67 98 87 79 85 105 88 13 74 53 14 21 105 42 110 33 35 33 39 43 100 65 30 24 32 38 39 31 34 35 64 4 65 72 46 98 91 107 67 73 67 4 65 37 86 111 45 32 67 94 49 30 25 41 44 96 32 23 70 69 4 71 68 66 18 93 108 91 106 95 36 40 47 63 67 77 91 109 48 28 38 102 101 9 82 83 80 90
Model 19A-126-100 Ref No. Part Number 1 720-04039 Description Knob Ref No. Part Number 41 783-1014A-0637 Drive Mounting Bracket Shoulder Screw, .5 x .29, 3/8-16 Description 2 784-5604A-0637 Chute Tilt Handle 42 738-0234 3 731-1313C Chute Tilt Cable Guide 43 741-0192 Flange Bearing w/ Flats 4 712-04063 Nylon Hex Lock Nut, 5/16-18 44 756-1181A Drive Pulley, 7” 5 603-0302-0637 Chute Tilt Bracket Assembly 45 747-1192 Rod, 1/2 x 11.55 6 710-0262 Carriage Bolt, 5/16-18 x 1.
Model 19A-126-100 20 Ref No. Part Number 81 911-0310 Clevis Pin, .5 x 1.18 82 911-1000 Belt Keeper Pin 83 712-04064 Nylon Hex Lock Nut, 1/4-20 84 912-3009 Hex Lock Nut, 5/16-18 85 914-0145 Click Pin, .092 x 1.64 86 714-0147 Internal Cotter Pin, .125 x 1.75 87 930-3000 Reflector 88 732-04237 Extension Spring .50 x 12.00 89 932-0594A Extension Spring .91 x 7.33 90 936-0192 Flat Washer, .531 x .93 x .09 91 736-3072 Flat Washer, .38 x .93 x .
Model 19A-126-100 1 5 4 2 3 2 1 6 Ref No. Part Number Description 1 712-0417A Flange Nut 5/8-18 2 941-0919 Ball Bearing 3 750-1096 Spacer 4 738-0976 Spindle Shaft 5 756-0999 Deck Pulley 7” 6 756-1173 Pulley 3.
Notes 22 8
Section 8 — Notes 23
CUB CADET LLC, P.O.
