Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator’s Manual Hydrostatic Garden Tractor — GT1554 VT WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No.
1 To The Owner Thank You Thank you for purchasing a Garden Tractor manufactured by Cub Cadet LLC. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.
12. A missing or damaged discharge cover can cause blade contact or thrown object injuries. 13. Stop the blade(s) when crossing gravel drives, walks, or roads and while not cutting grass. 14. Watch for traffic when operating near or crossing roadways. This machine is not intended for use on any public roadway. Slopes are a major factor related to loss of control and tip-over accidents which can result in severe injury or death. All slopes require extra caution.
Service Children 1. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. They do not understand the dangers. Never assume that children will remain where you last saw them. a. Keep children out of the mowing area and in watchful care of a responsible adult other than the operator. b. Be alert and turn machine off if a child enters the area. c.
Periodically check to make sure the blades come to complete stop within approximately (5) five seconds after operating the blade disengagement control. If the blades do not stop within the this time frame, your machine should be serviced professionally by an authorized MTD Service Dealer. Do not modify engine 4. Check brake operation frequently as it is subjected to wear during normal operation. Adjust and service as required. Notice Regarding Emissions 5.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER— ROTATING BLADES Never carry passengers. Never carry children, even with the blades off.
Section 2 — Important Safe Operation Practices d line (repr esent s a 15 ° slop e) WARNING! Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding mowers up and down slopes, never across the face of slopes. Use this page as a guide to determine slopes where you may not operate safely.
3 Assembly & Set-Up Contents of Crate • One Garden Tractor • One Oil Drain Tube • One Garden Tractor Operator’s Manual • One Briggs & Stratton Engine Operator’s Manual Tractor Set-Up One Deck Wash Hose Coupler Shipping Brace Removal Warning! Make sure the garden tractor’s engine is off, set the parking brake and remove the ignition key before removing the shipping brace.
Connecting the Battery Cables Checking Tire Pressure Warning! Maximum tire pressure under any circumstances is 30 psi. Equal tire pressure should be maintained at all times. California Proposition 65 Warning! Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
e. f. Remove the clevis pins and hairpin clips from the deck roller brackets on the left and right sides of the cutting deck. See Fig. 3-4. Position the deck roller brackets up or down through the slots on the rear of the deck until desired position is reached, then reattach with the clevis pins and hairpin clips just removed. Be certain that the left roller bracket and the right roller bracket are set in the same position.
4 Controls and Features Systems Indicator Monitor Ignition Switch Module Throttle/Choke Control PTO (Blade Engage) Knob Brake Pedal REVISIONS Drive Pedal Parking Brake Cruise Control Lever Lever Reverse Pedal Deck Lift Lever Seat Adjustment Lever Cup Holder Figure 4-1 Lawn Tractor controls and features are illustrated in Fig 4-1 and described on the following pages.
Throttle/Choke Control Drive Pedal The throttle/choke control is located on the left side of the tractor’s dash panel. This lever controls the speed of the engine and, when pushed all the way forward, closes the choke for cold starting. When set in a given position, the throttle will maintain a uniform engine speed. The drive pedal is located on the right side of the tractor, along the running board. Press the upper portion of the drive pedal forward to cause the tractor to travel forward.
Cruise Control Lever Brake If the Brake light illuminates when attempting to start the tractor’s engine, depress the brake pedal. PTO (Blade Engage) If the PTO light illuminates when attempting to start the tractor’s engine, move PTO lever into the disengaged (OFF) position.
5 Operation Starting the Engine TO AVOID SERIOUS INJURY OR DEATH • • • • • • • • • GO UP AND DOWN SLOPES, NOT ACROSS. AVOID SUDDEN TURNS. DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP. IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK DOWNHILL SLOWLY. KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES, ETC.) IN PLACE AND WORKING. REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADE(S). KNOW LOCATION AND FUNCTION OF ALL CONTROLS.
Reverse Caution Mode Driving The Tractor WARNING! Avoid sudden starts, excessive speed and sudden stops. The REVERSE CAUTION MODE position of the key switch module allows the tractor to be operated in reverse with the blades (PTO) engaged. NOTE: Mowing in reverse is not recommended. Warning! Use extreme caution while operating the tractor in the REVERSE CAUTION MODE. Always look down and behind before and while backing. Do not operate the tractor when children or others are around.
Driving On Slopes Setting The Cruise Control Warning! Never engage the cruise control lever while traveling in reverse. Refer to the SLOPE GAUGE on page 8 to help determine slopes where you may operate the tractor safely. WARNING! Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1⁄2 feet every 10 feet). The tractor could overturn and cause serious injury. To set the cruise control: 1.
Engaging the PTO Mowing Warning! To help avoid blade contact or a thrown object injury, keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area. Engaging the PTO transfers power to the cutting deck or other (separately available) attachments. To engage the PTO: 1. Move the throttle control lever to the FAST (rabbit) position. 2. Pull the PTO/Blade Engage knob outward into the engaged (ON) position. See Fig. 5-3.
6 Maintenance & Adjustments Maintenance Schedule Before Each use Check Air Filter for Dirty, Loose or Damaged Parts Every 25 Hours Every 50 Hours Every 100 Hours P Clean Hood/Dash Louvers Check Engine Oil Level Every 10 Hours Prior to Storing P P P P Clean and Re-oil Air Filter’s Foam Precleaner P Replace Air Filter Element P Change Engine Oil and Replace Oil Filter Clean Battery Terminals P P P P P Lube Front Axles and Rims Clean Engine Cooling Fins Lube Front Deck Wheels Lube Deck Spindl
3. Pop open the protective cap on the end of the oil drain valve to expose the drain port. See Fig 6-1. Spark Plug The spark plug should be cleaned and the gap reset once a season. Refer to the Briggs & Stratton Owner’s Manual for correct plug type and gap specifications. Hydrostatic Transmission The hydrostatic transmission is sealed at the factory and is maintenance-free. The fluid level cannot be checked and the fluid cannot be changed.
3. Attach the hose coupler to the water port on your decks surface. See Fig. 6-2. Front Wheels Each of the front wheel axles and rims is equipped with a grease fitting. See Fig. 6-3. Lubricate with a No. 2 multi-purpose grease applied with a grease gun after every 25 hours of tractor operation. Figure 6-2 4. Turn the water on. 5. While sitting in the operator’s position on the tractor, start the engine and place the throttle lever in the FAST (rabbit) position. 6.
Deck Spindle Grease fittings can be found on each deck spindle. See Fig. 6-4. Lubricate with 251H EP grease or an equivalent No. 2 multipurpose lithium grease. Using a grease gun, apply two strokes (minimum) or sufficient grease to the spindle shaft. Determine the approximate distance necessary for proper adjustment and proceed, if necessary. 1. Loosen (thread outward) the hex lock nut on the end of each deck hanger rod. See Fig. 6-5.
1. Leveling the Deck (Side to Side) Remove the hex nut on the top of ball joint. See Fig. 6-7. If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as follows: 1. With the tractor parked on a firm, level surface, place the deck lift lever in the top notch (highest position) and rotate both blades so that they are perpendicular with the tractor. 2.
Deck Rear Roller Adjustment The rear rollers on the mower deck are not designed to carry the weight of the deck. The rear rollers should be adjusted to approximately 1⁄4” to 1⁄2” above the ground when the deck is moved to the desired cutting height. Place the tractor on a smooth, flat surface, move the deck to the desired cutting height, and check the height of the rear rollers.
7 Service Cutting Deck Removal NOTE: If there is too much tension on the belt for it to be easily removed from the electric PTO clutch, carefully insert a 3⁄8” drive ratchet wrench (set to tighten) into the square hole found in the left-hand deck idler bracket and pivot it toward the tractor’s right side to relieve tension on the belt. See Fig. 7-2. To remove the cutting deck, proceed as follows: 1. Place the PTO/Blade Engage knob in the disengaged (OFF) position and engage the parking brake. 2.
5. Pull the deck support pin outward to release the deck from the deck lift arm. See Fig. 7-3. Cutting Blades WARNING! Shut the engine off and remove ignition key before removing the cutting blade(s) for sharpening or replacement. Protect your hands by using heavy gloves when grasping the blade WARNING! Periodically inspect the blade and/or spindle for cracks or damage, especially after you’ve struck a foreign object. Do not operate the machine until damaged components are replaced.
4. To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25°- to 30° angle. Always grind each cutting blade edge equally to maintain proper blade balance. See Fig. 7-6. Jump Starting WARNING! Never jump start a damaged or frozen battery. Be certain the vehicles do not touch, and ignitions are off. Do not allow cable clamps to touch. 1.
Caution: Always use a replacement fuse with the same amperage capacity as the blown fuse. 3. Remove the deck belt from around the three spindle pulleys and the two deck idler pulleys. NOTE: The idler pulleys may have to be loosened, but not removed, in order to remove the belt from around them. Tires 4. Route the new belt as shown in Fig. 7-8. WARNING! Never exceed the maximum inflation pressure shown on the sidewall of the tire.
8 Troubleshooting Problem Engine fails to start Cause Remedy 1. PTO/Blade Engage knob engaged. 1. Place knob in disengaged (OFF) position. 2. Parking brake not engaged. 2. Engage parking brake. 3. Spark plug wire(s) disconnected. 3. Connect wire(s) to spark plug(s). 4. Throttle control lever not in correct starting position. 4. Place throttle lever to FAST position. 5. Choke not activated 5. Push the Throttle/Choke control into the CHOKE position. 6. Fuel tank empty, or stale fuel. 6.
9 Replacement Parts Component Part Number and Description 759-3336 Spark Plug BS-792105 BS-792303 Air Filter Cartridge Pre-Cleaner BS-696854 Oil Filter BS-691035 Fuel Filter 954-0642 Drive Belt (Mowing Deck) 942-0677B 2-in-1 Deck Blade 918-0671B Deck Spindle Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at www.cubcadet.com.
Component Part Number and Description 734-04155 Deck Wheel 925-1707D Battery 951-3111 Fuel Tank Cap 746-04621 Throttle/Choke Control Cable 925-2054A Ignition Key 631-04070A Discharge Chute Assembly Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at www.cubcadet.
10 Attachments & Accessories The following attachments and accessories are compatible for Cub Cadet GT1554 VT. See your Cub Cadet dealer or the retailer from which you purchased your tractor for information regarding price and availability.
Notes 11 33
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board and MTD Consumer Group Inc are pleased to explain the evaporative emission control system warranty on your 2008 lawn mower. In California, new lawn mowers must be designed, built and equipped to meet the State’s stringent anti-smog standards.
WARRANTED PARTS: The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD Consumer Group Inc demonstrates that the lawn mower has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part.
CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY FOR SERIES 1000 & SERIES 1500 TRACTORS IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Please see the operator’s manual for information on required maintenance and service intervals. In the U.S.A.: Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, call 1-877-282- 8684 or log on to our website at www.cubcadet.com.