Cybex Eagle® Arm Curl Owner’s and Service Manual Strength Systems Part Number 11070-999 H www.cybexinternational.
Cybex Eagle® Arm Curl Owner’s and Service Manual Strength Systems Part Number 11070-999 H Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Eagle® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual.
Table of Contents 1 Safety Safety. . . . . . . . . . . . . . . . . . . . . . . . . . Warning/Caution Decals . . . . . . . . . . . Regular Maintenance Activities . . . . . . Using Proper Form . . . . . . . . . . . . . . . 1-1 1-2 1-5 1-5 2 Exercises General Exercise Guidelines . . . . . . . . 2-1 3 Customer Service Contacting Service. . . . . . . . . . . . . . . . Ordering parts . . . . . . . . . . . . . . . . . . . Return Material Authorization (RMA). . Damaged Parts . . . . . . . . . . . . . . . . . .
Cybex Eagle 11070 Arm Curl Owner’s Manual 1 - Safety Safety Read the Owner’s Manual carefully before assembling, servicing or using the equipment. It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the equipment and review all labels. WARNING: Serious injury could occur if these safety precautions are not observed: User Safety Precautions • Obtain a medical exam prior to beginning an exercise program.
Cybex Eagle 11070 Arm Curl Owner’s Manual • Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an uneven surface. • Make sure that all users are properly trained on how to use the equipment. • Make sure there is enough room for safe access and operation of the equipment. • Perform regular maintenance checks on the equipment.
Cybex Eagle 11070 Arm Curl Owner’s Manual 3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the equipment to the floor. 4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and anchoring fasteners with a qualified and licensed contractor. 5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position.. 6. Do not use machine until it is properly anchored.
Cybex Eagle 11070 Arm Curl Owner’s Manual A CAUTION Seat may fall if improperly engaged. Verify seat is secure before exercising to avoid injury. B 4520-362-4 C CAUTION Keep away from moving parts. Failure to do so could result in personal injury.
Cybex Eagle 11070 Arm Curl Owner’s Manual Arm Curl - 11070 C C A B DESCRIPTION PART NO. A. Warning Decal .................. 4605-381-4 B. Caution Decal................... 4520-362-4 C. Caution Decal...................
Cybex Eagle 11070 Arm Curl Owner’s Manual Regular Maintenance Activities Preventative maintenance activities must be performed to maintain normal operation of your equipment. Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities. The preventative maintenance actions are described in detail in Chapter 5. Briefly, they include: Daily 1. Clean upholstery. 2. Clean back panel. Weekly 1. Inspect all nuts and bolts for looseness.
Cybex Eagle 11070 Arm Curl Owner’s Manual 2 - Exercise MUSCLES USED Intended Use The intended use of this equipment is to aid or improve general physical fitness and exercise. For Commercial use. Instructions Read and understand all instructions and warnings prior to using this machine. See Chapter 1, Safety in the Eagle Owner’s Manual or consult with floor staff.
Cybex Eagle 11070 Arm Curl Owner’s Manual Set Up 1. Adjust seat height so that your arms are straight and fully supported by the pad. 2. Adjust chest pad so that the elbows align with the axis of rotation. 3. Grasp handles. Movement 1. Pull the handles up towards your shoulders.
Cybex Eagle 11070 Arm Curl Owner’s Manual 3 - Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Find information on the web at www.cybexintl.com or by e-mail at techhelp@cybexintl.com. Ordering Parts Fax order to 508-533-5183.
Cybex Eagle 11070 Arm Curl Owner’s Manual 1. Call the Customer Service Hot Line listed above for the return of any item that is defective. 2. Provide the technician with a detailed description of the problem you are having or the defect in the item you wish to return. 3. Provide the model and serial number of your Cybex equipment. 4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation and repair or replacement.
Cybex Eagle 11070 Arm Curl Owner’s Manual 4 - Assembly TOOLS REQUIRED • • • • • • • • 7/32” Allen wrench 3/4” Allen wrench 9/16” Wrench 3/4” Socket or wrench External snap ring pliers Phillips screwdriver Medium weight automotive engine oil Torque Wrench NOTE: Two people will be required for this procedure. NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each machine to allow for safe use and passage. 1.
Cybex Eagle 11070 Arm Curl Owner’s Manual B. With an assistant, carefully remove the six Button Head Socket Cap Screws (BHSCS) securing the two halves of the frame. See Figure 1. C. Carefully move each half through the door-way to the desired location. Locknut (4) BHSCS (4) Locknut (2) D. With an assistant, carefully attach each half together using the six BHSCS removed in step 4B. See Figure 1. E. Continue on with step 5B. BHSCS (2) 5. Remove shipping feet and remove the back shrouds. A.
Cybex Eagle 11070 Arm Curl Owner’s Manual G. Wipe guide rods clean over entire length. Lubricate with light coating of medium weight automotive engine oil. H. Carefully install each weight plate one at a time. NOTE: When installing weight plates, position plates so wide edges of bushing face upward and narrow edges of bushing face downward. See Figures 6A and 6B. T C E RR CO WIDE bushing edge faces upward Figure 6A I. G N RO W NARROW bushing edge NOTE: The narrow bushing edge must face downward.
Cybex Eagle 11070 Arm Curl Owner’s Manual E. Pull belt tight and secure belt to clamp with the two set screws. NOTE: Torque set screws 300-350 in./lbs. See Figure 9. Belt clamp insert Belt F. Place weight stack pin in each plate to verify proper installation. Belt clamp G. Without selecting any resistance, lift top weight up and down (simulating normal operation). H.
Cybex Eagle 11070 Arm Curl Owner’s Manual 9. Install weight plate decals. Front NOTE: You have the option to use pounds, kilograms or both. A. Slowly and carefully peel off back side of decal. See Figure 14. NOTE: When peeling off back cover, make sure that the decals remain attached to the front sticker. B. Align holes in decal with appropriate holes in weight stack. NOTE: Do not allow the adhesive to touch weight stack at this time. C. Insert a guide pin through each hole of the template.
Cybex Eagle 11070 Arm Curl Owner’s Manual This page intentionally left blank.
Cybex Eagle 11070 Arm Curl Owner’s Manual Chapter 5 - Maintenance All preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems equipment. NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your machines. Instruct all personnel in equipment inspection and maintenance actions and also in accident reporting/recording.
Cybex Eagle 11070 Arm Curl Owner’s Manual More Difficult Stains • Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90% water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration. • The same procedure can be used with full strength household bleach, if necessary. • Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes.
Cybex Eagle 11070 Arm Curl Owner’s Manual 4. Guidelines for cleaning front panel: • Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing. • Follow up the application with warm water rinse. • Don’t use abrasives or high alkaline cleaners. • Don’t leave cleaners on for long periods, wash immediately. • Don’t apply cleaners in direct sunlight or at elevated temperatures. • Don’t use scrapers, squeegees or razors. • Don’t clean with gasoline.
Cybex Eagle 11070 Arm Curl Owner’s Manual Weekly Procedures 1. Check all nuts and bolts for looseness. Tighten as required. 2. Inspect all belts (entire length) for any non-uniformity and wear.
Cybex Eagle 11070 Arm Curl Owner’s Manual 3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends in the cable and attachment points. Replace all worn cables immediately. The following conditions may indicate a worn cable: • A tear or crack in the cable sheath that exposes the cable. See Figure 1. Figure 1 • A kink in the cable. See Figure 2.
Cybex Eagle 11070 Arm Curl Owner’s Manual 4. Inspect bars and handles for wear, paying particular attention to tab area connecting points. Replace all worn handles immediately. 5. Inspect snap links for proper latching (indicates wear). Replace all worn snap links immediately. 6. Inspect for loose or worn grips. Replace all loose or worn grips immediately. 7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals. Replace all worn labeling immediately. 8.
Cybex Eagle 11070 Arm Curl Owner’s Manual Environment Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a shock due to the build-up of static electricity on your body and the discharge path of the unit.
Cybex Eagle 11070 Arm Curl Owner’s Manual Maintenance Page 5-8
Cybex Eagle 11070 Arm Curl Owner’s Manual 6 - Service Please refer to the next several pages for parts lists, exploded-view diagrams. NOTE: All inspections and repairs must be performed by trained service personnel only. Cybex will void warranty if non-Cybex replacement parts are used.
Cybex Eagle 11070 Arm Curl Owner’s Manual This page intentionally left blank Service Page 6-2
Cybex Eagle 11070 Arm Curl Owner’s Manual ARM CURL PRODUCT NO. 11070 D L E B H K O C I G F A NOTE: See exploded-view diagram for location of J (serial number decal) and N. DESCRIPTION A. B. C. D. E. F. G. PART NO. Caution Decal...................... 4520-362 Caution Decal...................... 8500-026 Warning Decal..................... 4605-381 Placard Decal.......................11070-610 Eagle Plaque........................11040-789 Arm Pads w/Wear Pad.........4800-119 Seat Pad................
Cybex Eagle 11070 Arm Curl Owner’s Manual ITEM QTY PART NO. DESCRIPTION ITEM PART NO.
Cybex Eagle 11070 Arm Curl Owner’s Manual ARM CURL MAIN ASSEMBLY DETAIL 21 25 54 37 49 49 76 54 44 48 49 39 60 70 49 3 67 52 49 54 95 23 59 52 1 54 49 36 59 55 95 1 38 53 73 54 59 29 34 69 62 89 90 33 40 88 43 92 22 68 42 72 46 2 45 87 81 74 56 4 54 81 93 24 77 17 64 82 61 66 30 68 79 50 58 71 16 59 30 19 30 50 18 54 86 66 20 58 81 80 47 53 4 17 68 45 61 2 Service Page 6-5
Cybex Eagle 11070 Arm Curl Owner’s Manual SHROUD AND GUIDE ROD ASSEMBLY DETAIL 8 12 9 65 83 84 85 63 65 44 78 44 26 51 31 5 13 7 28 94 7 14 75 6 28 96 32 75 6 14 65 5 65 11 11 65 Service Page 6-6 65
Cybex Eagle 11070 Arm Curl Owner’s Manual BELT ROUTING DETAIL 51 Service Page 6-7
Cybex Eagle 11070 Arm Curl Owner’s Manual ARM CURL TOP WEIGHT ASSEMBLY ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QTY 1 1 2 2 1 1 1 1 1 1 1 4 2 1 1 PART NO. 11040-366 11040-367 11040-369 11040-370 11040-427 11040-426 11040-424 11040-416 11040-425 BH030207 4700-250 BR030209 BR030220 HP016820 HP266765 DESCRIPTION Top Weight Assembly, Molded Hub, Molded Rod, Linkage Pin Rod Stem Cover Plate Cover, Top Weight Knob Pin, Weight Selector Lifting Post 10 External Retaining Ring .188 Internal Retaining Ring 1.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexinternational.com • techhelp@cybexintl.
