CWHDI-TxRx HDMI Wireless Transmitter & Receiver Set OPERATION MANUAL
Precautions Failure to follow the precautions described below may cause damage to this HDMI device and void the warranty. • DO NOT open the case. This will void the warranty, if you find a problem with this product, please return it to your retailer or seller who will assist you or provide you with a solution. • DO NOT use third-Party AC adaptors or power cords. This may damage the device. • DO NOT bump, jar or drop the product because it may cause damage and void the warranty.
Table of Contents 1. Introduction 1 2. Features 1 3. Package Contents 2 4. Operation Controls and Functions 3 4.1 4.2 Transmitter 3 4.1.1. Front Panel 3 4.1.2. Rear Panel 4 Receiver 5 4.2.1. Front Panel 5 4.2.2. Rear Panel 6 5. Remote Control 7 6. Connection Diagram 8 7. Specifications 9 8. Troubleshooting 10 Finden Sie ab Seite 9.
1. Introduction This wireless HDMI transmitter and receiver set uses baseband technology with a Wireless High Definition Interface (WHDI) to deliver uncompressed HD video and audio up to 15~30 metres open field, while maintaining superb, wire-equivalent quality and robustness with no latency. The transmitter and receiver both come with embedded antennas. 2. Features • Uncompressed wireless transmission of HD video/ audio at an equivalent quality to using a cable connection.
3. Package Contents • Wireless HDMI Transmitter unit. • Wireless HDMI Receiver unit. • 2 x 5V/2.6A DC power supply adaptors. • Operation Manual.
4. Operation Controls and Functions 4.1 Transmitter 4.1.1 Front Panel 4 5 6 PowerL ink CWHDI-TX Transmitter Power 7 HDMI1 HDMI2 HDMI3 Input 1 ID 2 3 1. Power button: Press to turn the system ON/OFF - paired units will both turn on/ off together when this button is pressed on either unit. 2. Input button: Press to select input source (1/2/3). 3.
• CEC and EDID repeater functionalities cannot be supported. • Multicast mode is not HDCP compliant. 4. 5. 6. 7. IR sensor. Power LED: The LED will illuminate when power is ON. Link LED: The LED flashes quickly during initial link procedure, flashes slowly during signal confirmation & remains solid when the link is established. Input indicator LED: The relevant LED will illuminate to indicate which input source is currently selected and being routed to the HDMI display. 4.1.
4. Operation Controls and Functions 4.2 Receiver 4.2.1 Front Panel 3 IR CWHDI-RX Receiver 4 5 Power Link Power ID 1 2 1. Power button: Press to turn the system ON/OFF - paired units will both turn on/ off together when this button is pressed on either unit. 2. ID button – press to initialise ID procedure.
4.2.2 Rear Panel HDMI OUT DC 5V 1 2 1. HDMI output: Connect this HDMI output to the HDMI input of your display with a HDMI cable. 2. Power: Plug the 5V DC power supply into this unit and connect the adaptor to an AC wall outlet.
5. Remote Control 1. Power: Press to turn the device ON/ OFF. POWER ID INPUT 2. ID: Press transmitter remote’s “ID” 1 button for 2 seconds and then 2 receiver remote’s “ID” for 2 seconds 3 ① ② ③ and wait for the system to pair. These systems are already paired before Transmitter CR-67 they leave the factory so it is not usually necessary for you to have to re-link the units. POWER ID 3. (transmitter remote only) Input source selection: Press 1, 2 or 3 to select your desired input source.
6.
7. Specifications Radio Power Transmit power is configurable up to 63mW (+18dBm) Video Resolutuions 480i/p, 576i/p, 720p, 1080i and 1080p(24fps/30fps), VGA@60/72, SVGA@60/72, XGA@60/70 Frequencies Supported Modulation 4.9 ~ 5.
8. Troubleshooting Situation Check Point/s Power LED does not illuminate when power is ON. 1. Check the right adaptor is being used - 5V/2.6 A is the correct adaptor. 2. Check all power connectors are plugged in correctly. 3. Press the power buttons to turn on the devices After powering up Tx & Rx, the Link LEDs are flashing quickly / slowly without displaying a picture. 1. Ensure your connected screen is On, and has the correct HDMI input selected, otherwise the Receiver unit’s link LED will flash. 2.
www.cypeurope.
