D-Link DI-713P Wireless Broadband Router User’s Manual
Contents Contents… .. ..................................................................................................2 Chapter 1 - Getting Started...........................................................................4 Introduction to Broadband Router Technology........................................6 Introduction to Firewalls ..........................................................................7 Introduction to Local Area Networking ...................................................
Virtual Server .........................................................................................37 Special Applications ...............................................................................40 Access Control .......................................................................................43 Wireless ..................................................................................................46 Miscellaneous Items ...................................................................
Chapter 1 - Getting Started Thank you for purchasing the D-Link Broadband Router. Your Broadband Router enables you to share your DSL or Cable Internet connection with computers on your wired or wireless network. This guide will explain the features and functions of the Broadband Router to help you get the most out of your Internet experience.
Wireless Broadband Router to expose it to the Internet and ensure complete Internet application compatibility even if specific ports are not known. Unlike proxy server or NAT software that requires the software server to remain visible on the Internet, no local computers are directly externally visible when using the Wireless Broadband Router. Also the Wireless Broadband Router, like broadband, is always on, removing the need to constantly boot a software server when access is desired from a client.
Introduction to Broadband Router Technology A router is a device that forwards data packets from a source to a destination. Routers work on OSI layer 3, which forwards data packets using an IP addresses and not a MAC address. A router will forward data from the Internet to a particular computer on your LAN. The information that makes up the Internet gets moved around using routers. When you click on a link on a web page, you send a request to a server to show you the next page.
Introduction to Firewalls A firewall is a device that sits between your computer and the Internet that prevents unauthorized access to or from your network. A firewall can be a computer using firewall software or a special piece of hardware built specifically to act as a firewall. In most circumstances, a firewall is used to prevent unauthorized Internet users from accessing private networks such as corporate LAN’s and Intranets.
Introduction to Local Area Networking Local Area Networking (LAN) is the term used when connecting several computers together over a small area such as a building or group of buildings. LAN’s can be connected over large areas. A collection of LAN’s connected over a large area is called a Wide Area Network (WAN). A LAN consists of multiple computers connected to each other. There are many types of media that can connect computers together. The most common media is CAT5 cable; UTP or STP twisted pair wire.
Introduction to Virtual Private Networking Virtual Private Networking (VPN) uses a publicly wired network (the Internet) to connect two different networks as if they were the same network. For example, an employee can access the corporate network from home using VPN, allowing the employee to access files and printers. Here are several different implementations of VPN that can be used. Point-to-Point Tunneling Protocol (PPTP) PPTP uses proprietary means of connecting two private networks over the Internet.
Introduction to Wireless Networking D-Link wireless products are based on industry standards to provide easy to use and compatible high speed wireless connectivity within your home or business. Strictly adhering to IEEE 802.11b the D-Link wireless family of products will allow you to access the data you want, when and where you want it. No longer will you be tethered to a workstation or forced to run new wiring. You will be able to enjoy the freedom that wireless networking delivers.
1. Keep the number of walls and ceilings to a minimum - Each wall or ceiling can reduce your D-Link Air Wireless products range from 1-30 meters. Position your Access Points, Residential Gateways, and Computers so that the number of walls or ceilings is minimized. 2. Be aware of the direct line between Access Points, Residential Gateways, and Computers - A wall that is .5 meter thick, at a 45 degree angle appears to be almost 1 meter thick.
Chapter 2 - Hardware Installation Procedure for Hardware Installation 1.Placement Your Broadband Router should be placed in a safe and secure location. To ensure proper operation, please keep the unit away from water and other damaging elements. Your Broadband Router can be mounted on a wall or a shelf using the screw-holes located on the bottom of the unit. Self-adhesive rubber feet are provided to stick on the bottom of the unit to protect the surface where you have placed the unit. 2.
Figure 2-1 Setup of LAN and WAN connections for the DI-713P 4.Connecting this product with your printer Use the printer cable to connect your printer to the printer port of this product. 5.Power on Connect the power cord to a power outlet and turn the power switch to the on position; the DI-713P will automatically enter the self-test phase.
M2 will be lit for about 10 seconds, and then M1 and M2 will flash 3 times to indicate that the self-test operation has finished. Finally, the M1 will continuously flash once per second to indicate that the DI-713 is in normal operation. Package Contents The D-Link DI-713P package should include the following items.
LED Panel The LED panel provides LED’s for device status. Refer to the following table for the meaning of each feature. LED Function Color Status Description POWER Power status Green On Blinking M1 System status 1 Orange Blinking M2 System status 2 The power is on Lack of power The DI-713P is functioning properly The DI-713P is working for some service The DI-713P is being configured or upgraded.
Rear Panel The rear panel features a LAN port, WAN port, Serial port and Factory Reset button. Refer to the following table for the meaning of each feature. Serial LPT LAN 1-3 WAN Reset 12VDC Port used to connect an external analog backup modem. Port used to connect a printer The RJ-45 Ethernet ports used to connect computers with network adapters directly to the DI-713P. The RJ-45 Ethernet port labeled WAN is used to connect your DI-713P to your DSL or Cable modem.
Chapter 3 - Basic Broadband Router Configuration Your Broadband Router provides a Web Configuration interface that can be accessed using standard web browsers such as Netscape Communicator or Microsoft Internet Explorer. Since the interface is web based (HTTP), your Broadband Router can be configured with any java and HTML compliant Internet browser in any operating system. This section will discuss the Web Configuration interface and how to use different options and settings.
In order to configure your Broadband Router you must input the administrator password into the System Password box and press the Log in button. The default System Password is admin. Once you have logged-in as administrator, it is a good idea to change the administrator password to insure a secure connection to your Broadband Router. The Tools section described later in this manual describes how to change the password.
Device Information This screen displays the status of your Internet Connection. The WAN Port Status box shows the Status of your connection to your ISP. If there is no information shown in this section, you will be unable to connect to the Internet. If you have successfully followed the Quick Install guide to setup your Internet Connection, you should see a Renew button. Click the Renew button to renew your connection with your ISP.
Useful Tools The Useful Tools screen allows you to change the administrator password, view the system log, reboot your Broadband Router, backup your configuration, clone the MAC address, reset your Broadband Router to original settings, and perform a firmware upgrade. To change the administrator password, click your mouse inside of the Old Password box and type in the old password. Then click inside of the New Password box and type the password that you would like to change to.
The View Log button will display a log of events that has occurred since you last turned on your Broadband Router. Use this to determine problems with your ISP connection. It will show you events where an intruder has tried to access your network, and give you information that can be used to determine if your Broadband Router is functioning correctly. Below is a sample System Log. WAN Type: Dynamic IP Address (2.
Upgrade button and select the backup file that you saved using the Backup Setting button. Your Broadband Router comes preprogrammed with it’s own Ethernet Address or Media Access Control (MAC) Address. The Clone MAC button will copy the MAC address to match the MAC address of another Ethernet port to ensure an Internet connection with some ISP’s. Contact your ISP to determine if this feature is needed to connect to the Internet.
from the D-Link Support web site to ensure that your Broadband Router is upgraded properly and to ensure proper operation. While upgrading the firmware, DO NOT turn the power off. Turning the unit off while upgrading could render the unit inoperable.
Setup This section is crucial to enable your Broadband Router to work with your ISP. The Setup screen will allow you to change the IP address of your Broadband Router, change the WAN type, and allow you to modify the settings that will ensure a proper connection to the Internet. Your ISP should provide most of the settings found in the Setup screen to you. If you followed the Quick Install Guide successfully, these settings should be set and you should be able to access the Internet.
proper connection. Refer to the Console Mode section in the Appendix for instructions on how to change the password. Pressing the Change… button next to the WAN Type field will display the Change WAN Type screen shown below. Static IP Address The Static IP Address field should be checked if your ISP assigns you an IP address. This means that your ISP has given you an IP address that you will use to connect to the Internet through their service.
You will need to input the correct values in each of the WAN fields. Your ISP may have provided each of these values for you. Or, you may have written them down while you followed the Quick Install Guide. After you have input all of the correct values, click Save and reboot your Broadband Router for the changes to take affect.
following screen. Some Cable Modem ISP’s such as the @Home network require the Host Name field to be used. If you not sure, contact your ISP to make sure you are inputting the correct values. Enable the Renew IP Forever checkbox if you want your IP address renewed each time it expires even if the system is idle. After you have input all of the correct values, click Save and reboot your Broadband Router for the changes to take affect.
as you would do with a dial-in modem, then you are probably using PPPoE. If you are simply connected to the Internet when you turn on your computer, you probably are not. The safest way to check is to call your ISP or read the documentation provided when you signed up for your Internet service. Once you have selected PPP over Ethernet, you will be shown the following screen. You will need to input the correct values in each of the blank fields. Your ISP may have provided each of these values for you.
you are not sure which settings should be used, please contact your ISP. In the Maximum Idle Time field, input the maximum time that your connection can be used before your ISP disconnects you. If 0.0.0.0 is inputted in the Primary and Secondary DNS fields, these values will be retrieved from your ISP automatically. After you have input all of the correct values, click Save and reboot your Broadband Router for the changes to take affect.
You will need to input the correct values in each of the blank fields. Your ISP may have provided each of these values for you. Or, you may have written them down while you followed the Quick Install Guide. If you are not sure which settings should be used, please contact your ISP. If 0.0.0.0 is inputted in the Primary and Secondary DNS fields, these values will be retrieved from your ISP automatically.
DHCP Most networks under the TCP/IP environment include settings for a Host IP, Subnet Mask, Gateway, and DNS configurations. Configuring each computer on the network to use the correct settings can be rather cumbersome. Fortunately, a DHCP Server provides a rather simple approach to handling all of these settings without the headache of configuring each computer. In effect, the DHCP server can provide all of the required information automatically each time a client computer on your network boots up.
The IP Pool Starting Address is the first IP Address that will be assigned to one of your clients. No address will be lower than this starting address. If you have this set to 100, then no computer on your network will be given an IP address lower than 192.168.0.100. Likewise, the IP Pool Ending Address is the last IP address that the DHCP server will provide. You can also restrict the number of computers that the Broadband Router can support in DHCP by limiting the pool of IP addresses.
Wireless The Wireless Setting screen enables you to change the settings related to your wireless network. This screen is important in configuring your wireless adapters to connect to your Wireless Broadband Router. The Network ID (SSID) field is the name of your network. This field must have the same name that your wireless adapters use in their network settings. The Channel field must also be set to the same settings as your wireless adapter.
Wireless Broadband Router must decode each piece of data moving to and from your wireless adapter. The security key that you use must be the same as your wireless adapter. Print Server The DI-713P provides the function of a network print server for Microsoft Window 98, Windows ME, Windows NT and Windows 2000. Please refer to the Print Server Quick Install Guide for installing the port and printer installation.
Chapter 4 - Advanced Broadband Router Configuration The default configuration of the Broadband Router will stop most unrecognized information from entering your network. The only IP Address visible to the outside Internet is the IP address of the Broadband Router. Some applications and services require special configuration in order to operate correctly with the Internet.
To access the Advanced Router Configuration screens, click the Advanced link below. If, at any time, you wish to return to the Basic Configuration screens, click the Basic Link below.
Virtual Server In some situations, you may want to provide E-Mail or FTP services from a computer on your network, and you may want those services to be accessible to users outside of your network. The Virtual Server screen allows you to configure specific computers on your network to provide these services to remote users.
to communicate over the Internet. All requests to this port will be forwarded to the computer specified in the Server IP field. The Virtual Server screen allows you to configure many different servers. To make configuring the Virtual Server screen easier, the most popular services have been predefined using the Well known services box near the bottom of the screen, as shown below. To use the Well known services box, click on the - select one - box to display a list of popular services.
Click the Reboot button to reboot the Broadband Router for the changes to take effect. You can also click the Undo button to undo your changes. Note: Only one TCP/IP address can be assigned to each service port.
Special Applications Some applications, such as video conferencing software and games that can be played over the Internet, require specific ports to be open to allow communication to and from your network. Due to the firewall function of your Broadband Router, these applications will not work without special settings. The Special Applications screen allows you to specify which ports should be opened and allowed to communicate with computers outside of your network.
incoming ports. The Incoming Ports field is where you specify the incoming ports that the application uses. Click the box in the Enable column to enable the application. To make configuring the Special Applications screen easier, the most popular applications have been predefined using the Popular applications box near the bottom of the screen, as shown below. To use the Popular applications box, click on the - select one - box to display a list of popular applications.
changes. Note: Only one TCP/IP address can be assigned to each service port.
Access Control The Access Control screen allows you to assign different access rights (allow or block) for each group of users. You can divide users into different groups to have similar access rights. To enable access control, click the checkbox next to Enable in the Access Control field. Next, you can define the access control of all users not assigned in groups 1 through 3. For example, you can block all users from using port 21 (FTP) by specifying port 21 in the Default Group field.
Tip: You can specify more than one port per group by using dashes (-) and commas (,). For example: 1-10, 20 will block or allow ports 1 through 10, and also 20. Explanation: • • Default Group has no right to access Internet (Allow nothing) Group 1 has 50 members (192.168.0.100 - 192.168.0.149). They can send mail (port 25), receive mail (port 110) and browse the Internet (port 80). Port 53 (DNS) is necessary to resolve the domain name. • Group 2 has 50 members (192.168.0.150 - 192.168.0.199).
take effect immediately.
Wireless The Wireless Setting screen enables you to change the settings related to your wireless network. This screen is important in configuring your wireless adapters to connect to your Wireless Broadband Router. The Network ID (SSID) field is the name of your network. This field must have the same name that your wireless adapters use in their network settings. The Channel field must also be set to the same settings as your wireless adapter.
Wireless Broadband Router must decode each piece of data moving to and from your wireless adapter. The security key that you use must be the same as your wireless adapter.
Miscellaneous Items The Miscellaneous Items screen allows you to select one computer as a DMZ Host and to configure one remote computer to be able to access the Broadband Router web configuration. DMZ Host DMZ, or DeMilitarized Zone, means that one computer can have full access to the Internet without the protection of the firewall. This allows a computer to be exposed to unrestricted two-way communication outside of your network. To enable DMZ, type the IP address in the box provided.
proper firewall protection. Remote Administrator Host In general, only you, or members of your network, should access the web configuration interface of the Broadband Router. In some circumstances though, you may want to have access to the Broadband Router web interface to change settings while you are away from your network. The Remote Administrator Host field allows you to input the IP address of one remote computer so that it can access the web configuration interface to perform administrative tasks.
Click the Reboot button to reboot the Broadband Router for make the changes to take effect. You can also click the Undo button to undo your changes.
Chapter 5 - Console Mode In some situations, you may need to access your Broadband Router from the serial port interface known as the Console Mode. Console Mode allows you to change the IP address, and password, toggle the DHCP server setting, and restore default settings to your Broadband Router. You may use the HyperTerminal program provided with Microsoft Windows to access the Console Mode. A null modem cable is required to connect the COM port of your computer to the COM port of the Broadband Router.
The following screen will be shown: Firmware Version = 2.51 build 9 Command List: IP (set device IP; e.g. IP 192.168.123.254) PW (set new PassWord; e.g. PW admin) DS (toggle Dhcp Server setting) SR (Save new setting and Reboot) RR (Restore default setting and Reboot) Current Setting: Device IP = 192.168.0.1 DHCP Server = Enable > If the command list screen doesn’t show, start this step over again and watch the LED’s on the Broadband Router closely so that you press the ENTER key at the correct time. 5.
Chapter 6 - Troubleshooting In the event that you are unable to connect to or use your Broadband Router, please refer to the following troubleshooting guide. After each problem description, a possible cause and problem resolution is provided. If this section does not help you fix the problem, go to the D-Link web site (www.dlink.com) for additional troubleshooting tips. If neither of these helps, please contact D-Link Technical Support for additional help.
Resolution: § Download and upgrade the latest firmware. § Make sure the correct firmware has been used while upgrading. Use only the firmware provided on D-Link’s web or FTP sites. § Use only the power adapter provided. The Link or Act LED’s do not turn on. Cause: § The network cable is not connected. § The network cable is connected but not the right type, whether it be patch or straight-through. Resolution: § Make sure that both ends of the cable are connected. § Try using another cable.
lock up. When the Broadband Router locks up, it will not affect the computers attached to it. You may need to restart the client computers to regain Internet access. Although sometimes inconvenient, a lock-up is an indication of an attack. Part of the design of the Broadband Router is to act as a decoy for such traffic. If your computer locked up instead you may have lost changes to open files, lost data, or corrupted your operating system or hard drive.
§ § is set to the same subnet as the Broadband Router. For example, if the Broadband Router is set to 192.168.0.1, change the IP address of your computer to 192.168.0.15 or another unique IP Address that corresponds to the 192.168.0.X subnet. Follow the instructions outlined in the Appendix section labeled “Console Mode” to check the basic settings of your Broadband Router. You can verify the IP Address of the Broadband Router to make sure that your computers IP Address are set correctly.
ISP Connection Problems I can access the Broadband Router, but I can’t connect to my ISP. Cause: § Your DSL or Cable modem is not functioning correctly. § The cable is connected from the WAN port of the Broadband Router to your DSL or Cable modem. § The wrong connection type is used in Setup. § The username and password is not input correctly. § If using @Home service, the computer name is not input correctly. § Your ISP may only allow one MAC address to access the Internet.
Internet Application Problems My online game does not work. Cause: § The NAT table has filled up. § The correct settings have not been used to open the correct ports for your application. § The unit has stopped working or crashed. Resolution: § If you are trying to connect to game servers and your connection has stopped working, wait a few minutes or turn the unit off and then on again. Games send out many requests to many different servers trying to find the best game server for your connection.
My E-Mail program doesn’t receive my E-Mail Cause: § The Domain Suffix is not set correctly. Resolution: § Some email applications require you to enter the Domain Suffix when you configure your network and TCP/IP settings. The Domain Suffix is the unique identifier for your email server. The Domain Suffix is the Internet Protocol (TCP/IP) address of the email server you are using. Your cable modem or DSL provider usually lists it somewhere on your invoice.
Wireless Troubleshooting Can’t access the Broadband Router from a wireless network card Cause: § Settings are not the same among each wireless adapter. § Out of range. § IP Address is not set correctly. Resolution: § Make sure that the Mode, SSID, Channel and encryption settings are set the same on each wireless adapter. The default SSID and Channel that the Wireless Broadband Router uses is “default” and “6” respectively.
Appendix 1 - Using PING In Windows, Microsoft has provided a small utility called PING that can be used to troubleshoot your IP address and connection. The PING utility is used mainly to test the connection between your computer and a client computer. Using the PING utility to check a connection can be helpful in determining where the problem is, whether it be your Broadband Router, your DSL or Cable modem, or your ISP.
§ If any one of these attempts results in an unsuccessful PING, your connection is not complete. If a PING is unsuccessful between you and your DSL or Cable modem, then your connection is not setup correctly. If it is unsuccessful when PINGing your ISP or an Internet site, then your connection is setup correctly but there is a problem with your ISP or the Internet site you tried to PING is unavailable. The screen shown below is an example of an unsuccessful PING. C:\>ping 192.168.0.1 Pinging 192.168.0.
Appendix 2 - Using WINIPCFG In Microsoft Windows versions 95 through Me, Microsoft has provided a small utility called WINIPCFG that can be used to troubleshoot your IP address and connection. The WINIPCFG utility is used mainly to view, release and renew your IP Address configuration. Windows NT (including Windows 2000) has a similar utility called IPCONFIG that can be used to perform similar tasks.
Internet. If you are using DHCP, click the Release and then the Renew buttons to receive the correct settings. If you manually set your network settings, make sure that the IP Address of your Broadband Router is set in the Gateway portion of the TCP/IP settings in your network settings. § Click on "More Info" to display additional IP information. The important settings to watch for in this screen are in the Host Information box.
correct DNS information. Also check the DHCP server box to make sure that you are connected to the right DHCP server.
Contacting Technical Support D-Link provides free technical support for customers within the United States. U.S. customers can contact D-Link technical support through our web site, e-mail, or by phone. United States technical support is available Monday through Friday from 6:00 a.m. to 6:00 p.m. (PST). Web: http://www.dlink.com Email: support@dlink.
Technical Specifications Standards: • IEEE 802.3 10BASE-T Ethernet • IEEE 802.3u 100BASE-TX Fast Ethernet • ANSI/IEEE 802.3 NWay auto-negotiation Protocols Supported: • TCP • IP • NAT • UDP • PPPoE • DHCP (Client and Server) Management: • Web-Based Ports: • LAN: NWay 10BASE-T/100BASE-TX Fast Ethernet • WAN: 10BASE-T • RS-232 (DB-9) Serial Additional details available at D-Link’s web site (www.dlink.com).
Wireless Specifications General Wireless Specifications: • IEEE 802.11b Wireless LAN, Wi-Fi Compatible Access Point Frequency Band: • 2.4 ~ 2.4835 GHz (subject to local regulation) Access Point Number of Channel: • USA & Canada: 11 Access Point Frequency Range: • 5 Mbps Access Point Data Rate: • • • • 11 Mbps 5.
D-Link Offices AUSTRALIA CANADA CHILE CHINA DENMARK EGYPT FRANCE GERMANY INDIA ITALY JAPAN RUSSIA SINGAPORE S. AFRICA SWEDEN TAIWAN U.K. U.S.A. D-LINK AUSTRALASIA Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-1077 TOLL FREE: 1800-177-100 (Australia), 0800-900900 (New Zealand) URL: www.dlink.com.au E-MAIL: support@dlink.com.au, info@dlink.com.
Limited Warranty D-Link Systems, Inc. (“D-Link”) provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor.
any part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. The Warranty Period shall extend for an additional ninety (90) days after any repaired or replaced Hardware is delivered.
days after any replacement Software is delivered. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link.
RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. The packaged product shall be insured and shipped to D-Link, 53 Discovery Drive, Irvine CA 92618, with all shipping costs prepaid.
by anyone other than D-Link. Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS.
PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. GOVERNING LAW : This Limited Warranty shall be governed by the laws of the state of California.
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures Warnung! Dies ist in Produkt der Klasse B. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen. Advertencia de Marca de la CE Este es un producto de Clase B.
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Register by mail or online at http://www.dlink.com/sales/reg/ Registration Card Print, type or use block letters. Your name: Mr./Ms_____________________________________________________________________________ Organization: ________________________________________________Dept.
