Planning Guide

All specications subject to change without notice.
Phone: [phone]www.dacor.com
PLANNING
GUIDE
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Document # PG05-006
Revised 12/11/14 Page 5/6
DR30DI[H] Self-Rimming Installation With Downdraft Vent
■ Only model DR30DI[H] may be installed with a downdraft vent. Use
only Dacor downdraft vent model ERV3015.
■ A self-rimming countertop configuration is required for downdraft vent
installation. self-rimming installation of the range and downdraft vent
create a “built-in” look where the range trim overlaps the countertop
on both sides and the downdraft vent overlaps the countertop in back.
It is also possible, if the cabinets are deep enough, to self rim the
front portion of the range into the cabinet face immediately behind the
control panel and door trim or behind the side panels. The rear range
trim will partially cover the front of the downdraft vent chassis in back.
■ For existing countertop cutouts that are 30 inches wide, contact your
dealer about custom trim kits.
Cabinet face
Countertop
Back of
control
panel
DR30DI[H] range
3/8” min. (1.0 cm) flat countertop
overhang required behind cutout
28 3/4” (73.0 cm)
3 1/4 inch
side panel
ERV3015
downdraft
3/8” min. (1.0 cm) space
required behind
ERV3015
chassis to clear stiffener
H
Range trim resting
on countertop
rear wall recommended
Non-combustible
countertop opening
cabinet opening
below countertop
29 1/4” (74 3 cm)
27 1/2” (69.9 cm)
30” (76.2 cm)
2 5/8”
(6.7 cm)
10” min.
(25.4 cm)
both sides
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
Notch countertop
overhang to width of
cabinets
3/8” min. (1.0 cm)
countertop
overhang
downdraft vent opening
H
Combustible side
wall above range
below countertop
To cabinet face
To countertop
front
J
K
TOP VIEW
SIDE VIEW
MODEL DR30DI/ERV3015 COUNTERTOP SELF-RIMMED
ONLY, CABINET DEPTH: 23 5/8” TO 26 7/8”
(WITHOUT 3 1/4 INCH SIDE PANELS INSTALLED)
Cabinet tolerances: -1/16”, (+1.6 mm) -0
Cabinet face
Countertop
Back of
side panel
rests against
cabinet face
DR30DI[H] range
3 1/4 inch
side panel
ERV3015
downdraft
3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener
H
3/8” min. (1.0 cm) flat countertop
overhang required behind cutout
28 3/4” (73.0 cm)
Range trim resting
on countertop
rear wall recommended
Non-combustible
countertop and
cabinet opening
29 1/4” (74 3 cm)
27 1/2” (69.9 cm)
2 5/8”
(6.7 cm)
10” min.
(25.4 cm)
both sides
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
Notch countertop to
3/8” min. (1.0 cm)
countertop
overhang
downdraft vent opening
H
Combustible side
wall above range
below countertop
Cabinet face
To countertop
front
K
30” (76.2 cm)
TOP VIEW
SIDE VIEW
MODEL DR30DI[H]/ERV3015 COUNTERTOP AND CABINET
FRONT SELF-RIMMED, CABINET DEPTH: 23 5/8” MINIMUM
(WITH 3 1/4 INCH SIDE PANELS INSTALLED)
H J K
20 5/8”
(52.4 cm)
0” (0 cm) to
3 1/4” (8.3 cm)
0” (0 cm) to
5 3/8” (13.7 cm)