LCD TELEVISION INSTRUCTION MANUAL DLP-26C2 DLP-26C3 DLP-32C2 DLP-32C3 DLP-32C6
Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk electric shock.
Important Safeguards Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain them safely for future reference. Follow all operations and instructions accordingly. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
Important Safeguards 13. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 14. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 15.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. In case of an accident, please unplug the unit from the outlet immediately. To reduce the risk of electric shock, do not remove cover or back. No user serviceable parts inside. Refer to qualified service personnel for repair. Do not put any object that contains water the unit.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. Please keep the user's manual in a safe place for future reference. Do not cover the top of the television set. Ventilation will be prevented, and it may be a cause of fire if the product is internally overheated.
Table of Contents Installation and Maintenance Antenna Connection 9 Video Connection 12 Camcorder & Video Game Connection 13 DVD Player Connection 14 STB Connection 15 PC Connection 16 Cable TV Broadcasting Connection 18 Connect with the Dolby Digital AMP 19 Name of Each Part 20 Basic Guide Parts of the Remote Controller 22 Method To Use Basic Menu 24 To Watch TV 25 Setting Up TV Stations 27 Selection of AV and Multimedia Input Signal 31 Application Guide Screen Adjustment 33 S
Supplied Accessories Make sure that the following accessories are provided with the product. R WE PO TE MU DIA TIME MUL ALL REC ND SOU URE PICT ECT ASP PR V O L U MEN V O L OK UT P.INP PR V PR PRE AP P.SW ILL P.ST DE P.MO MIC DYNA P.PR A RAM 3D PANO P.
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR : Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. 2. Connect the combining adapter to the antenna input at the left side of the TV set. WHEN USING THE COMBINING ADAPTER : You may obtain the combining adapter at your closest Service Center.
Antenna Connection CTV Antenna Connection Such community TV Antenna installation may be found in most of co-op apartments. When a coaxial cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right. Antenna socket at the left side of the TV set ANT/CABLE When a feeder cable is used : Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right.
Antenna Connection Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses Single Antenna Connection VHF Antenna BACK OF THE TV SET UHF Antenna HDMI INPUT PC INPUT AV1 AUDIO AV2 OPTICAL Pr Pb R L Y S-VHS AV3 L - AUDIO - R COMPONENT ANT/CABLE Separate Antenna Connection.
Video Connection Connecting with an External Source You may connect an S-Video input to enjoy clearer and brighter picture images. You can make the connection with the AV3 input. BACK OF THE TV SET HDMI INPUT PC INPUT AV1 AV2 AUDIO S-VHS AV3 L - AUDIO - R Note : If S-video and RCA jack are connected the same time, The TV set will only detect the S-Video mode. • If your AV device has both Video OUT terminal and S-Video OUT terminal, the S-Video connection is recommended for better picture quality.
Camcorder & Video Game Connection Watching the Camcorder Recording on TV 1. Prepare the S-video and RCA connector. 2. These connectors connect to S-video or AV 3 as shown in the picture below. 3. Turn on the TV set and camcorder/video game. 4. Select AV3/S-video mode, using the ” ” button of the Remote controller or “ ” button of the TV set.
DVD Player connection When connecting with a component cable and Euro SCART cable BACK OF THE TV SET HDMI INPUT PC INPUT AV1 AV2 OPTICAL AUDIO Pr Pb R L Y S-VHS AV3 L - AUDIO - R COMPONENT Note : • When you connect with the component video, please check the colour of the cable between the DVD and TV set.
STB(Set Top Box) Connection When connecting with a HDMI cable BACK OF THE TV SET HDMI INPUT PC INPUT AV1 AV2 AUDIO OPTICAL Pr Pb R L Y S-VHS AV3 L - AUDIO - R COMPONENT Set Top Box When connecting with a component cable BACK OF THE TV SET HDMI INPUT PC INPUT AV1 AV2 AUDIO OPTICAL UP-GRADE PORT Pr Pb R L S-VHS AV3 L - AUDIO - R COMPONENT Set Top Box 15 Y
PC Connection When connecting with PC(D-Sub) cable. 1. First adjust resolution of the PC. (640 X 480, 800 X 600, 1024 X 768) 2. Connect between PC and TV set using the D-sub and Audio cable as shown in the picture below. 3. Turn on the PC and TV set. 4. select PC mode by pressing “MULTIMEDIA” button on the remote control or ” ” button of the TV set. BACK OF THE TV SET HDMI INPUT PC INPUT AV1 AV2 AUDIO OPTICAL Pr Pb R L Y S-VHS AV3 L - AUDIO - R COMPONENT When connecting with a HDMI cable.
PC Connection PC CONNECTION NOTES: 1) The resolution of the TV set is best at 1024 768(XGA). 2) If there is a [Vertial Frequency] setting menu in the [Display] Menu of the PC, adjust the frequency to 60Hz. 3) If the PC resolution is too high, it may be hard to detect signals. Select a suitable resolution. 4) HDMI input port receives only digital Signal. 5) Depending on the graphic card when you plug & unplug the HDMI connection the screen may not display correctly. Restart the computer if this happens.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to any of the Component input and SCART input AV1, AV2.
Connect with the Dolby Digital AMP. If you connect the optical output to a Dolby digital AMP, you can listen to better sound.
Name of Each Part Front / Side Panel Buttons on the TV set have the same functions as those of the remote controller. 1 MENU 3 6 Front Panel 2 PR 4 5 Side Panel (Right) Control Key Buttons. Buttons : Each time you press this button, the TV will cycle through: TV => AV1 => AV2 => AV3/S-Video => PC => HDMI => Component MENU Button : Use this button to enter and exit the MENU. Buttons : Use this buttons to change your TV’s volume or to move the cursor in the menu.
Name of Each Part Side and Rear Panel Side Panel HDMI INPUT PC INPUT AV1 AV2 AUDIO OPTICAL Pr Pb R L S-VHS AV3 L - AUDIO - R COMPONENT Rear Panel 21 Y
Parts of the Remote Controller This remote controller is universal; thus, it may be convertible for TV, Video, CTV, etc. 1. MUTE PICTURE POWER SOUND MULTIMEDIA ASPECT RECALL PR V O L V O L MENU PREV PR OK PR P.MODE DYNAMIC BASS P.STILL P.SWAP P.INPUT 3D PANORAMA P.PR STILL P.PR 1 2 3 4 5 6 7 8 9 LOCK SLEEP 0 ? X (MUTE) : Press this button, and the sound goes off. Press again, and the sound returns. 2. (POWER) : TV on/off button in Stand-By mode. 3.
Parts of the remote controller 17. MUTE PICTURE POWER SOUND MULTIMEDIA ASPECT RECALL PR V O L V O L MENU PREV PR OK PR P.MODE DYNAMIC BASS P.STILL P.SWAP P.INPUT 3D PANORAMA P.PR STILL P.PR 1 2 3 4 5 6 7 8 9 LOCK SLEEP 0 ? X : You can select sound mode in Mono, Stereo, Dual1, Dual2, NiCAM STEREO. It works only in TV mode. 18. STILL : Press this button to freeze the picture. 19. NUMBER : Press the numbers on this board, you can select PR directly in TV mode. Note.
Method To Use Basic Menu Basic Menu - The basic menu appears on the screen if you press the “MENU” button of the remote control. - There are 5 items Picture, Screen, Sound, Function, and Install in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. 1. Press the "MENU" button. • The main menu appears if you press the “MENU” button.
To Watch TV On/Off, Number, Mute, Recall, ◀/▶, ▼/▲ - Buttons with same name in the main body performs the same function. Press the " " button of the front side of the set or Remote controller . • The buttons of the remote control and the main body operate only when AC power is turned on. Note : You can also turn on the TV using “▼PR▲” or digit key in the ST-BY mode.
To Watch TV 1. Turning on the TV. • Plug AC Cord into a power outlet. • The Stand By LED lamp turns on in red colour. • Press “ ” button of the main body or “POWER” button on the remote control. • The Stand By LED lamp on the front panel begins to fliker in red and green colour and the TV turns on. 2. Adjust program. • Select the desired program by pressing the “▼PR▲” button or the number button. POWER PR PR MENU V O L PR 3. Adjust volume. •Sound reduces by pressing the “◀VOL” button.
Setting Up TV Stations Auto Tuning - All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. 1. Press the “MENU” button to select the Install menu. • Move the selection bar to the Install menu with “▼PR▲”buttons. PR V O L MENU PICTURE V O L PICTURE MODE BRIGHTHESS CONTRAST COLOUR SHARPNESS TINT COLOUR TEMP PR PR V O L MENU I 50 80 50 50 50 Normal ACCESS POSITION 2. Select the "Auto Tuning".
Setting Up TV Stations Manual tuning 1. Press the Number buttons(0~9) or the “▼PR▲” button to select a program number you want. 1 2 3 4 5 6 7 8 9 PR V O L MENU V O L PR 0 2. Locate the selection bar on the Manual tuning at the Install menu. • Press the “MENU” button to select the Install menu. • Move the selection bar to the Install menu with “▼PR▲” buttons. • Place the selection bar on Manual Tuning and press the “VOL▶“ button. ◀VOL▶ ▶” buttons. 3.
Setting Up TV Stations Setup The Setup menu shows you information as follows: - Picture information: PAL, SECAM, and SECAM-L - Sound information: L, DK3, DK2, DK1, I, BG - Station name, Program number and Real channel number. 1. Searching for channels in the Setup menu • Press the “▼PR▲“ buttons to select a program number you want. • Move to SETUP in the Install menu. • Select the colour and sound system which you want. • Search a real channel with “▼PR▲“ buttons. 2.
Setting Up TV Stations Edit The Edit menu shows you information as follows: - Program position assignment: Program number and Station name, Real channel number. - Skip information: Red (Skip Yes), White (Skip No) PR 1. Deleting the program positions. • Move to EDIT in the Install menu. • Move the selection bar to program number to ◀VOL▶“ buttons. delete with the “▼PR▲” or “◀ • Press the Delete(Yellow) button. V O L MENU EDIT V O L PR P.MODE P.STILL DYNAMIC BASS 2.
Selection of AV and Multimedia Input Signal When watching video, Camcorder, DVD, Cable TV with AV - See page 12 for connection method of Camcorder and Video. - When pressing ” ” button on the TV set, screen changes as follows: TV => AV1 => AV2 => AV3/S-Video => PC => HDMI => Component => TV 1. Pressing the “ ”(AV) button on the remote controller.
Selection of AV and Multimedia Input Signal When connecting PC, STB, DVD with Multimedia 1. Pressing the "MULTIMEDIA" button on the remote controller. • The screen changes as follows: PC => HDMI => Component => PC MUTE PICTURE PC Clock POWER SOUND MULTIMEDIA ASPECT 12 : 00 RECALL PR V O V O MENU COMPONENT HDMI Clock Clock 12 : 00 12 : 00 HDMI & PC mode 1. For optimum picture quality, use 1280x720p computer or set top box output at a 60Hz refresh rate.
Screen Adjustment When setting up various screen modes - The user may select various screens designed for a good picture without adjusting the brightness, contrast or colour individually. 1. Pressing the “PICTURE” button.
Screen Adjustment When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Colour, Sharpness, etc to the user’s taste. 1. Select "PICTURE" by pressing the "MENU" button. • The menu screen appears as follows. PICTURE PR V O L MENU PR V O L PICTURE MODE BRIGHTHESS CONTRAST COLOUR SHARPNESS TINT COLOUR TEMP POSITION 2. Select and adjust each items. • Move to the PICTURE menu.
Screen Adjustment Adjustment of Screen Size in TV and AV mode - Randomly change the size of the screen. - The AUTO screen operates when power is first turned on. PICTURE SOUND MULTIMEDIA ASPECT RECALL PR 1. Pressing the "ASPECT" button on the remote controller.
Screen Adjustment Adjustment of the screen in the PC mode 1. Adjustment of the H-Position • Move to H-Position in the Screen menu. ◀VOL▶” buttons to adjust the horizontal • Press the ”◀ position of displayed image. SCREEN PR V O L MENU V O L PR SCALE H-POSITION V-POSITION PHASE CLOCK AUTO-ADJUST POSITION 2. Adjustment of the V-Position • Move to V-Position in the Screen menu. ◀VOL▶” buttons to adjust the vertical • Press the ”◀ position of displayed image.
Sound Adjustment When selecting various sound modes 1. Sound mode selects what you want. • Press the "SOUND" button, then the sound status changes as followed : Normal => Speech => Music => Favourite => Normal MUTE PICTURE POWER SOUND MULTIMEDIA ASPECT RECALL PR V O L SOUND MODE NORMAL SOUND MODE SPEECH SOUND MODE FAVOURITE SOUND MODE MUSIC MENU V O L Note. • Normal : normally recommended sound. • Favourite: Allows the user to adjust as desired.
Sound Adjustment When adjusting sound to taste - The user can enjoy various sounds by adjusting Sound Mode, Equalizer, Balance and Amp Speaker. 1. To adjust the audio equalizer • Move to Equalizers in the Sound menu. • Select and use the relevant frequency by pressing the ”▼PR▲” button. • You can adjust the degree of the frequency by using ◀VOL▶” button. the ”◀ Note: • Whenever you adjust the audio equalizer, it stores in the Favourite mode.
Sound Adjustment Multi-Sound and Stereo 1. Mono Sound Selection • During Stereo sound reception if the stereo is weak, you can switch to MONO by pressing the button. Then the colour of "MONO" character will change to Red. In Mono reception the depth of sound is improved. • To switch back to stereo, press the MTS PREV PR P.MODE DYNAMIC BASS P.STILL MTS P.SWAP P.INPUT 3D PANORAMA P.PR STILL P.PR 1 button again. MONO OK PR 2 3 MONO Note: • only works in RF mode. 2.
Selection of Language Selection of Language When you first turn on the TV set, the window of language selection is displayed automatically. 1. Press the “MENU” button and select "Function". PR V O L MENU FUNCTION V O L PR LANGUAGE TIMER CHILD LOCK MGDI DEMO OSD HALFTONE POSITION 2. Select "Language" by pressing “◀VOL▶“ button. MENU V O L PR PR V O L • The language change as the followed.
Adjustment of Time Adjustment of Time - You must previously adjust current time in order to reserve Automatic On/Off. 1. Manual clock setting • Move to Timer in the Function menu. • To go to the Clock, press the “VOL▶“ button. • Place the cursor to Hour / Minute with “◀VOL▶” buttons. • Set the Hour / Minute with the “▼PR▲”buttons. • Place the cursor to Clock with “◀VOL▶” buttons and then press the “MENU” button to complete.
Adjustment of Time 4. Set up of Off Time • Move to Timer in the Function menu. • To go to the Off Timer, press the "▼PR▲" button. • Select Off Timer to "Yes" • Set the Off time in the same way as above for the Clock. The set will turn off at the selected time. PR V O L FUNCTION V O L MENU CLOCK AUTO CLOCK AUTO CLOCK PR WAKE UP WAKE UP TIME WAKE UP PR OFF TIMER OFF TIME PR POSITION Note.
Other Functions 1. Child Lock • Move to Child Lock in the Function menu. • Select Child Lock to "On" using the “VOL▶” button • You can also select this function using the "LOCK" button on the remote controller. FUNCTION PR V O L MENU PR V O L LANGUAGE TIMER CHILD LOCK MGDI DEMO OSD HALFTONE 0 ACCESS POSITION Note. ON MENU EXIT • This prevents the use of the TV set without the remote control. • If TV set is set up Child Lock, LED will cycle through red/green for the ST-BY mode.
Teletext Teletext SWITCHING TELETEXT ON/OFF Press the “TELETEXT” button ( ). The index page or the page viewed last will appear. Press the “TELETEXT” button again to return to the TV mode. NOTE: Teletext works only in TV/AV mode. COLOUR BUTTONS IN TOP/FLOF TELETEXT A red, green, yellow and blue field is shown at the bottom of the screen.
Troubleshooting Symptoms and Solutions Please check the following list prior to calling Daewoo Electronics Service Centre for assistance Symptom Neither picture nor sound Check items - Check the contact of sockets is all right. - Check the TV main power is on. Picture is OK but no sound - Check the Volume control is set to minimum or mute. Sound is OK, but no colour. - Check the colour control and adjust it properly. - Check the program is in colour and not in black & white. The picture has image.
Troubleshooting In PC mode Symptom “OUT OF RANGE” appears on the screen OUT OF RANGE “NO SIGNAL” appears on the screen. Check items - Check the resolution and frequency of your PC. Then, adjust them to optimum condition for LCD TV. - Refer to the table of PC mode input format (If registered resolution and frequency on the table no listed then no picture will be displayed.) - Ensure that the signal cable is firmly connected to PC and TV. NO SIGNAL Image is not clear. - Adjust the PHASE control.
Standard of Product Screen Size LCD Panel TV System Power Source 32"(81Cm) 37”(94Cm) Aspect Ratio 16:9 16:9 16:9 Resolution 1366 x 768 (WXGA) 1366 x 768 (WXGA) 1366 x 768 (WXGA) Pixel Pitch 0.4215 mm 0.51075 mm 0.200 x 0.600 mm Contrast Ratio 3000:1 3000:1 3000:1 676 x 530 x 230 mm 806 x 626.5 x 230 mm 940 x 720 x 328.5 mm Dimension(W x H x D) Set Dimension Power Consumption 26"(66Cm) Max.
