Installation & Assembly

ManualsBrandsDarby Home Co ManualsCandle-Style ChandeliersSeagraves 5 - Light Candle Style Drum Chandelier

(5)B10CandelabraBase60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

1of3

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Quick Link

6” Rod

12” Rod with

Nipple

Small Loop

12” Rod

Shade

Cover

Socket

Cup

Cap

Crystal

Socket Assembly

Finial

STEP 1 Assemble Small Loop, Rods, Socket Assembly and Finial-

A. Thread Finial (J) onto the bottom center of Socket Assembly (K).

Hand tighten until snug.

B. Determine Rods (B/C/D) to be assembled to Socket Assembly (K)

Socket Orientation

according to your hanging height.

C. Pass the supply wires and ground

wire through the chosen rods

(B/C/D) and the Small Loop (A).

Thread Socket Assembly (K), the

chosen Rods (B/C/D) and Small

Loop (A) together. Hand tighten

until snug.

D. Remove Lock Screws from Socket

Assembly (K). Place the Shade (E)

(Step 1 Continued)

from top end of fixture. Pass it over Small Loop (A) and chosen rods

(B/C/D). Fit the bottom rod into the Gap of Support Washer in the

Shade (E) and align holes on Support Washer to mounting holes on

top ends of Socket Assembly (K). Secure the Shade (E) by using

removed Lock Screws. Hand tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling: use (1) 6” rod and (1) 12” rod

9’ ceiling: use (1) 6” rod and (2) 12” rods

10’ ceiling: use (2) 6” rods and (2) 12” rods

Figure 1

Supply Wires

and Ground Wire

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) Tighten until snug..

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

Gap

Lock Screw

Support

Washer

Assembly Instruction

Go to Care + Maintenance the selection.

Summary of content (3 pages)

PAGE 1
Assembly Instruction Go to Care + Maintenance the selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) B10 Candelabra Base 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
STEP 3 - Install Canopy Chain Loop and Nipple STEP 5 - Wire Connections * Pliers is required for this step. A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at least 0.25” from the end. Pass one Lock Washer (BB) over the end of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the Nipple (DD). By using pliers, thread the Hex Nut (CC) against the Canopy Chain Loop (EE) and hand tighten until snug. B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).
PAGE 3
6” Dia. FINISH: PALLADIAN BRONZE 56” OVERALL HEIGHT INCLUDES SINGLE CHAIN, QUICK LINK, (2) 6” RODS AND (2) 12” RODS 7” 15.75” 13.75” 25” Dia.