Operating instructions

OPERATING INSTRUCTIONS
1. TO OPERATE: Plug cord into a grounded
120V, 60 Hz outlet. Select desired operating
speed with pull cord on the rear of the
motor:
First pull: High Second pull: Medium
Third pull: Low Fourth pull: OFF
NOTE: THIS FAN IS VERY HEAVY.
Failure to securely hold onto head assembly
while adjusting head angle
could result in personal injury.
2. TO ADJUST HEAD ANGLE: While holding
head rmly, loosen knob under motor (turn
counterclockwise). Tilt head to desired
position FIRMLY retighten knob under
motor.
3.OSCILLATION: Push down oscillation
knob on motor housing to make fan
head move from side to side.
NOTE FOR OSCILLATING MODELS: FAN
IS SHIPPED WITH 90º OSCILLATION
ANGLE. FOR 45º OSCILLATION ANGLE,
CONNECT THE OSCILLATION LINK TO
THE INNERMOST HOLE IN THE CAM
GEAR. (Inset A)
NOTE: If fan head is to be angled down
further than 10º, it is recommended
to use the 45º oscillation feature.
Not doing so may shorten the life of
the fan transmission.
CAUTION: THE SECONDARY SUPPORT CA-
BLE PROVIDED SHOULD BE USED ANYTIME
THE CIRCULATOR IS MOUNTED OVERHEAD
FOR ADDITIONAL SAFETY.
SECONDARY SUPPORT CABLE
(Figures 7 and 8)
1. Loop one end of Cable around the Large
Guard Wires of both the Front and Rear
Grills.
2. Attach a Cable Clamp with the "U" on the
tail side of the loop leaving a tail approxi-
mately 1 to 2 inches. Tighten Clamp Nuts.
Make sure no part of the Cable interferes
with the Blade.
3. Wrap the other end of the Cable around a
secure building joist, truss, or other support
near the Fan. Take up all excess slack in the
Cable.
CAUTION: USE ONLY THE MOUNTING
HARDWARE WHICH IS RECOMMENDED
FOR USE ON THIS FAN.
4. Attach the remaining Cable Clamp as indicated
in Step 2. The excess tail should be trimmed to
extend 1 to 2 inches past the Clamp.
5. Check the Assembly to assure the Blade is
free of all obstructions.
CAUTION: Use of the secondary support cable
does not guarantee protection against injury
of persons, mounting of both the circulator
and cable could fail if subjected to abuse, neglect
or improper installation.
Figure 8
Large Guard
Wires
Figure 7
Secondary
Support
Cable
MAINTENANCE
WARNING: ALWAYS UNPLUG THE
CORD BEFORE MOVING OR SERVICING.
WARNING: DO NOT IMMERSE FAN
IN WATER!
CLEANING: Use a soft cloth and mild
soap solution such as liquid dish washing
detergent. Dry all parts completely before
reconnecting to power supply.
CAUTION: Do not use gasoline,
benzine, thinner, harsh cleaners, etc.
as they will damage the Fan. NEVER
use ALCOHOL OR SOLVENTS.
SERVICING: All other servicing, with the
exception of general user maintenance,
should be performed by an authorized ser-
vice representative. LUBRICATION: Precision
bearings are sealed at the factory for life
and do not require further lubrication.
STORAGE: Store the Fan, with these instruc-
tions, in a clean and dry place.
1.
2.
3.
(Inset A)
Cam Gear
90˚
45˚
4
Dayton Operating Instructions & Parts Manual 2RDZ8/2RDZ9
Rev. A 11/08
5085456
Dayton les Instructions Opérantes & Sépare le Manuel 2RDZ8/2RDZ9
Les Parties de réparation Enumèrent pour 24” & 30” Design Silencieux
Oscillant Mont Mural Ventilateur
1 Pale 5081015BKB 5082036BK 1
2 Moteur 02030260 02030260 1
3 Grille avant avec enjoliveu 5097030 5097145 1
4 Grille arrière 5097022BK 5097012BK 1
5 Sac de boulonnerie A 02098012 02098012 1
6 Sac de boulonnerie B 05098022 05098022 1
7 Base 5062095BKT 5062095BKT 1
2
N°
de Nºs de référence pour les modèles
Réf. Descripción 2RDZ8 (24”) 2RDZ9 (30”) Qte.
Pour obtenir des pièces de rechange, appelez le 1-800-323-0620
Veuillez fournir les renseignements suivants :
- Numéro de modèle
- Numéro de série (le cas échéant)
-Description et numéro de la pièce tels qu’indiqués dans la liste des pièces
1
3
2
5
6
7
4
17Rev. A 11/08 5085456