Owner's Manual

ManualsBrandsDCS ManualsBarbecue48 Inch Built-In Gas Grill with 1,115 Sq. In. Cooking Area, Stainless Steel Grates, 126,500 BTU Output, 3 Grill Burners, 2 Side Burners, Integrated Rotisserie Burner, Smoker Tray with Burner, Grease Management and Hood Temperature Gauge: Liquid Propane

TO LIGHT THE GRILL BURNER:

Open the grill lid and/or remove the top grate cover from side burner (for BH1-48RS) before lighting. Turn all knobs to

“OFF”. Turn the main gas supply on. If you smell gas, shut-off gas supply and call for service.

Grill Lighting Instructions:

The grill knob is connected to the electronic ignition module. Pushing in on the burner knob will activate the igni-

tion module to get a spark.Push in and turn the selected burner knob to HI/SEAR position. Release the knob when

the burner lights. If burner does not light in 4 to 5 seconds, turn

knob “OFF” and wait 5 minutes before trying again so any accumu-

lated gas may dissipate.

Grill Match Lighting:

If the burner will not light after several attempts, then the burner

can be match lit. If you’ve just attempted to light the burner with

the ignition, allow 5 minutes for any accumulated gas to dissipate.

Keep your face as far away from the outdoor appliance as possible

and hold a paper book match over the hole located on the top left

for burner on the left, or the right hole for the right burner (Fig. 26 and Fig. 27). Push and turn the control knob

which is centered on the burner where the lit match is located, to “SEAR”. If the burner does not light in 4 seconds,

turn the knob off, wait 5 minutes and try again.

NOTE:

Improper lighting procedures can cause the LP tank flow control to activate, resulting in reduced heat output. If this is sus-

pected, to reset flow control, shut off all burner controls and LP cylinder valve, wait 30 seconds, then turn LP cylinder valve

on extremely slowly, wait five (5) seconds and push and hold the ignition

button and turn burner valve on to “SEAR”.

For BH1-48RGI and BH1-36RGI models see the Quick Start Guide for how

to use the griddle and Infrared Hybrid Burner

TO LIGHT DUAL SIDE BURNERS 48BQR MODELS ONLY:

CAUTION!

The side burner cover may be hot if the grill burners are in operation.

Side Burners Lighting Instructions:

First remove the burner cover and any cooking utensils from the

burner grate. The control knob is connected to the electronic igni-

tion module. Pushing in on the control knob will activate the ignition module

to get a spark. Push the control knob in and turn to “HI”. If burner does not

light in 4 to 5 seconds, turn knob “OFF” and wait 5 minutes before trying

again for any accumulated gas to dissipate. If the burner will not light after

several attempts, check the trouble shooting instructions on page 33.

Side Burners Match Lighting:

Hold a lit paper book match near the burner ports, turn the control knob

counterclockwise to “HI”. Move your hand immediately once the burner is

lit. Rotate the control knob to the desired setting.

Note:

If you are using propane gas, a slight pop or flash may occur at the burner ports a few

seconds after the burner has been turned “off”. This “extinction pop” is normal for

propane gas.

Side burners:

Your side burner is equipped with burners typical of those used in restaurants. These

burners are designed for maximum cleanability and controlability. The burner should

never be operated if the cap is not in place (Fig. 29).

USING THE GRILL

LIGHTING INSTRUCTIONS

FIG. 26

FIG. 27

FIG. 28

FIG. 29

Cap

Control Knobs

SEAR

OFF

All knobs must be in the OFF position before

opening LP tank valve.

Now open the LP tank valve two (2) full

turns min.

Failure to follow the steps in the order shown may cause the Flow

Limiting Device to activate resulting in extremely low gas ow and

improper operation.

Attach regulator hose assembly to tank.

WARNING