Installation Guide

Base PlatesCap Plates
5 3/8” x 5 3/8” x 1/8” low carbon steel.
The plate has two 5/16” holes, four raised lugs to fit the column size, two 1/4”
slotted holes, four 3/8” oval holes, one 9/16” counter sink hole and one 1/2” hex
head screw (5/16” hex head bit not included). Available to fit both 3 1/2” OD or 4”
OD columns. Unpainted.
Additional Caps
Lally Lock Cap Adjustable Base Set
Adjustment Screws
Bearing Plate
Base Plate
End Plate
Lally Lock Base Plate
Lally Lock Beam Plate
Lally Lock Saddle Plate
Beam Plate with ring Saddle Plate with ring
Made from 1/4” low carbon steel. The plate has two keyholes and two 3/8”
holes with a 19/32” counter sunk hole in the center of the plate to accept a
1/2” bolt. The plate can be used for a 3 1/2” or 4” column.
Red fasteners are for LVL Gray fasteners are for 2x’s
- - - - Available sizes- - - -
• 3 1/8” x 8” x 1/4” for 2 2x’s • 3 5/8” x 8” x 1/4” for 2 LVL
• 4 5/8” x 8” x 1/4” for 3 2x’s • 5 3/8” x 8” x 1/4” for 3 LVL
• 6 1/8” x 8” x 1/4” for 4 2x’s • 7 1/8” x 8” x 1/4” for 4 LVL
Made from 12 gauge low carbon steel with eight
3/16” holes. A specially designed hole and bolt to
connect the plate to the column is located in the
center of the plate. Painted black.
- - - - Available sizes - - - -
• 3 1/8” x 4” x 11 1/2” for (2) 2x’s • 5 3/8” x 4” x 11 1/2” for (3) LVL
• 3 5/8” x 4” x 11 1/2” for (2) LVL • 6 1/8” x 4” x 11 1/2” for (4) 2x’s
• 4 5/8” x 4” x 11 1/2” for (3) 2x’s • 7 1/8” x 4” x 11 1/2” for (4) LVL
Theses plates need to be welded to comply
with code.
3 1/2” column set includes:
(1) Base plate: 4 7/8” x 4 7/8” x 3/8”
plate with (4) 1/2” threaded holes and (2)
5/16” counter sunk holes for concrete screws.
(1) Bearing plate: 4 7/8” x 9” x 1/4” plate
with (4) keyholes for concrete screws (2) 5/8”
dimples and (2) 1/2” threaded holes.
4” column set includes:
(1) Base plate: 5 3/8” x 5 3/8” x 3/8”
plate with (4) 1/2” threaded holes and (2)
5/16” counter sunk holes for concrete screws.
(1) Bearing plate: 5 3/8” x 9 1/2” x 1/4” plate
with (4) keyholes for concrete screws (2) 5/8”
dimples and (2) 1/2” threaded holes.
Both sets include:
(4) 1/2” x 3 1/2” adjustment screws (hardened steel)
(2) Phillips head concrete screws.
(4) Hex head concrete screws.
All Plates Painted Black
Holds 55,000 pounds
3” adjustment
Self leveling
2 threaded holes in the bearing plate allow
the plate to be connected to the base plate.
Made from 1/4” low carbon steel with four exclusively designed keyholes.
A 1” steel collar is welded to the plate to fit both 3 1/2” OD or 4” OD columns
Four concrete screws are included to fasten to your footing (5/16” hex drive or
regular screw driver bit not included). This plate is designed for a base plate.
The steel collar ensures against lateral displacement. For uplift protection the
plate must be welded to the column. Painted black.
- - - - Available sizes- - - -
• 3 1/8” x 8” x 1/4” • 3 5/8” x 8” x 1/4”
• 4 5/8” x 8” x 1/4” • 5 3/8” x 8” x 1/4”
• 6 1/8” x 8” x 1/4” • 7 1/8” x 8” x 1/4”
5 3/8” x 5 3/8” x 1/8” low carbon steel. The plate has two 5/16” holes, four raised lugs
to fit the column size, two 1/4” slotted holes, four 3/8” oval holes, one 1/4” counter sink hole
and one phillips head concrete screw (phillips head bit not included). Available to fit both
3 1/2” OD or 4” OD columns. Unpainted.