Use and Care Guide

USE AND CARE SPECIFICATIONS
DESCRIPTION: Ipe Oil
®
Hardwood Deck Finish, by DeckWise
®
, is an oil based product that protects and conditions hardwoods
such as Ipe, Cumaru, Tigerwood, Massaranduba and Mahogany while also maintaining an all-natural appearance. It has been
produced with professional results in mind, providing exceptional penetration, water repellency and U.V. protection.
VEHICLE TYPE
Solvent based, blend of natural oils and synthetic alkyds.
Low 250 VOC formula Ipe Oil
®
contains VOC exempt solvent.
COLORS
Available in Natural Brown
VISCOSITY
15-18 Seconds Zahn #2 at 77F
VOC CONTENT
250 g/l (with water / exempt materials)
BOILING RANGE
F: 302 to 554
C: 105 to 290
FLASH POINT
F: 104
C: 40
SOLIDS BY WEIGHT
40-55%
SPECIFIC GRAVITY
.92
WEIGHT PER GALLON
8.2 Pounds
COVERAGE
Rough Wood: 150 to 250 square feet per gallon
Smooth Wood: 200 to 300 square feet per gallon
DRY TIME
Allow 24 hours in good drying conditions
APPLY WITH
Brush, lint-free rag, roller, airless spray
PACKAGING
One U.S. gallon / 3.785 Liters
SURFACE PREPARATION
For best results, always clean new, gray or dirty hardwood before applying
Ipe Oil
®
. Use DeckWise
®
Deck & Wood Cleaner Part 1 and for hardwood
with tannic acid bleeding or rust stains, use Deck & Wood Brightener Part
2. Allow hardwood to completely dry for at least 24 to 48 hours. New
hardwood should be aged at least 6-8 weeks and cleaned before applying
product.
SPECIAL INSTRUCTIONS
Before applying, this product should be mixed thoroughly. Ensure that
all settled material on bottom of can is evenly incorporated, and intermix
multiple containers for an even blend.
Apply Ipe Oil
®
when surface temperatures are between 45F and 90F. If
surface is hot to the touch, it is too hot to apply product. Do not apply
product if precipitation is expected within 24-48 hours.
Brush, Roller & Rag Application: For the best results, utilize a high
quality 3/8” nap roller, pad applicator or stain brush. To minimize lapping,
maintain a wet edge lengthwise and do not break in the middle of boards.
One coat is sufficient for most applications. Always apply oil onto the
boards parallel to the grain of the wood. NOTE: Product not absorbed
into the wood within 30-45 minutes must be thoroughly removed.
Spray Application: When spraying, back brush or roll to prevent sags and
runs. Cover surrounding areas to protect from over spray. For airless spray,
use .015” to .019” tip size for best results. NOTE: Product not absorbed
into the wood within 30-45 minutes must be thoroughly removed.
Wipe Off Excess: Depending on temperature and direct sunlight verses
shade, soak time may need adjusted. It is essential to wipe excess oil
off completely and attention paid to pooling after application. Continue
to wipe excess oil until no surface sheen or leeching is noticeable. Wood
surface must NOT look wet and will have a matte finish.
SHAKE, STIR & MIX WELL • Questions/Comments: [e-mail]
The Ipe Clip
®
Fastener Company, LLC
The Ipe Clip
®
Fastener Company, LLC
Phone: [phone] • Email: [e-mail]
Web: www.DeckWise.com
DeckWise
®
, The Ipe Clip
®
Fastener Company, LLC • 2111 58th Ave. East, Bradenton, FL 34203C • All rights reserved. ©Copyright 2018
Rev:12/10/2019
250
VOC
250
VOC