ORIGINAL INSTRUCTION MANUAL EVO control unit
3 1 2 4 5 9 6 10 11 7 12 8 COMPONENT DESCRIPTION 1 Display 7 –Key 2 Docking station 8 Scroll key 3 Handlebar remote 4 On/Off key 10 Fixing handlebar 5 Confirm key 11 6 +Key 12 USB interface 9 Lever display fixing Contacts
GO SWISSDRIVE WELCOME NOTES ON THE ORIGINAL INSTRUCTION MANUAL Dear Customer, Pay particular attention to the following symbols: Thank you for choosing an Evo control unit. Our Evo control unit stands for high Swiss quality and it will give you a great deal of pleasure and together with your GO SwissDrive system enjoyment when riding.
GO SWISSDRIVE 1. INTRODUCTION 2.2. Mounting the display on the docking station The Evo control unit is the communication interface with the GO SwissDrive system. It offers you a huge number of functions and individualisation options. The following chapter is a short overview with the description of the basic operation of the Evo control unit. You will find a detailed description of all functions and configuration options of the Evo control unit in the following chapters. 2. SHORT OVERVIEW 2.1.
GO SWISSDRIVE The handlebar remote has five keys (1). Their functions are described in short in the following. For a detailed description see the chapter “Key functions of the handlebar remote”. i If your vehicle has a throttle mode for moving backwards, this function is activated by pressing the –key long in the driving mode. This function is analogous to the throttle mode towards the front. On/Off key (1a): With the On/Off key (and with any other key) you can activate the entire GO SwissDrive system.
GO SWISSDRIVE The currently selected assistance level is visualized by the graphics on the left edge of the display (1). By means of the +/–keys you can select between five positive assistance levels and two recuperation levels. By pressing the +key you select a higher assistance level, by pressing the –key you select a lower assistance level. By selecting assistance level 0 the motor assistance is turned off. I The current speed of the pedelec/e-bike is indicated with one digit behind the decimal point.
GO SWISSDRIVE The date and the time can be adjusted in the configuration menu under “Date and time” (1). To enter the data, call up the configuration menu by pressing the Scroll key until the configuration screen appears. Continue by navigating with the +/–keys of the handlebar remote to the button “Date and time“ and then press the Confirm key.
GO SWISSDRIVE 3. 4. Function in the stopwatch menu: Start the stopwatch by pressing the Confirm key when the stopwatch menu is indicated. Pressing the Confirm key once again stops the measurement. Pressing the Confirm key long saves the measurement and resets the stopwatch. If you want to continue the measurement after a pause, just press the Confirm key once again. Function in the standstill menus: At standstill the Confirm key serves to confirm selected options or the setting of parameters.
GO SWISSDRIVE 4. OVERVIEW MENU STRUCTURE The menu structure of your Evo control unit consists of different menus which are enabled depending on the riding situation. For road-safety reasons the menu selection is limited during the ride to the main menu, the tour data and the stopwatch. At standstill further menus are enabled in which for example settings can be made or a mobile phone can be connected via Bluetooth.
GO SWISSDRIVE You can switch between these menus by pressing the Scroll key. A detailed description of the individual menus is given in the respective chapters. In the standstill mode the display of your Evo control unit is subdivided into three sections already described in the preceding section: the status bar, the menu position and a variable menu section, where you can select between the different standstill menus.
GO SWISSDRIVE Service tool (1): Your well-equipped dealer has the GO SwissDrive service tool. With this tool he can make various settings on your pedelec/e-bike. Once the display is connected via the USB or Bluetooth interface with the service tool, this is visualised by means of the service tool symbol. Error (2): An error occurring in the GO SwissDrive system of your pedelec/e-bike is indicated on the display. First, you will see a pop-up appearing shortly (see chapter “Pop-ups and warnings”).
GO SWISSDRIVE Display Battery state of charge 100% - 90% When the motor is operated in the recuperation mode, this is visualised with a whitecoloured bar (1). A The charge control indicator always refers to the current capacity of the battery. In this connection, keep in mind that the maximum chargeable capacity of a battery may decrease with a growing number of charging cycles. 89% - 80% 79% - 70% 6. MAIN MENU The main menu provides the essential information required during the ride.
GO SWISSDRIVE The remaining range is indicated with a three-digit value in kilometres or miles. In addition, the remaining range is visualised with an analogous circular instrument (1). The algorithm for the calculation of the remaining range not only considers the total distance ridden with the pedelec/e-bike (total data), but also the last kilometres.
GO SWISSDRIVE 8. STOPWATCH With the stopwatch function (1) of your Evo control unit you can stop the time taken for a distance covered. Each measurement consists of a time measurement and the distance covered which is indicated in kilometres or miles. Start the stopwatch by pressing the Confirm key when the stopwatch menu is indicated. Pressing the Confirm key once again stops the measurement (2). Pressing the Confirm key long saves the measurement and resets the stopwatch.
GO SWISSDRIVE Subsequently, a list symbol (1) is displayed with the phone symbol in the status bar indicating that a new call or a new SMS was registered in the phone menu. In the list the calls and SMS are sorted by date and time whereas the latest call or the latest SMS are indicated at the top. If the number of the incoming call or incoming SMS is recorded in the phone book of your mobile phone, the name recorded in your mobile phone instead of the phone number is indicated in the list.
GO SWISSDRIVE I The error indicator is completed with possible corrective measures in concise form. In case the error cannot be remedied with these measures, have the pedelec/e-bike checked by a dealer. You can delete the list of errors occurred by navigating with the +/–keys of the handlebar remote to the “Delete list“ button (1) and by pressing the Confirm key. In addition, the service menu shows the time or the mileage for the next service at your dealer under the error list.
GO SWISSDRIVE For the display of the distances and speeds you can select between the metric system and the imperial system. In the metric system distances are displayed in kilometres (km) and the speeds in kilometres per hour (km/h); in the imperial system distances are displayed in miles (m) and speeds in miles per hour (mph). A Your Evo control unit offers various menu languages between which you can select. The possible options depend on the configuration of the manufacturer of your pedelec/ e-bike.
GO SWISSDRIVE In the next step enable the Bluetooth interface of your Evo control unit by navigating in the submenu “Bluetooth” (1) to the button “Enable Bluetooth” and press the Confirm key subsequently. Now, your Evo control unit tries to set up a connection with a mobile phone in the vicinity. To allow the connection with the mobile phone, open the GO SwissDrive App “EvoConnect“ on the mobile phone, select your Evo control unit and confirm the request regarding the set up of a Bluetooth connection.
GO SWISSDRIVE 34 Bluetooth (1): The Evo control unit has an integrated Bluetooth chip and can be connected via Bluetooth 4.0 with various compatible devices, such as for ex. mobile phones. When a new Bluetooth connection was set up, you are informed with a pop-up. In case a greater volume of data is saved, individual pop-ups visualise the beginning and the successful end of the saving process. If an error occurs during the saving process, another pop-up opens with the respective information.
GO SWISSDRIVE 15. CHARGING A MOBILE PHONE VIA USB CONNECTION The docking station (1) of your Evo control unit has a USB interface (2). The USB interface can be used either for the transfer of data or for charging a mobile phone. To charge a mobile phone connect the mobile phone via USB cable with the USB interface of the docking station. The charging process starts as soon as the connection is set up. 36 I Keep in mind that you can only charge a mobile phone with the GO SwissDrive system switched on.
GO SWISSDRIVE 17. SERVICING AND MAINTENANCE OF THE EVO CONTROL UNIT 17.1. Servicing the Evo control unit Clean your Evo control unit (1) immediately when it comes in contact with substances which may result in spot formation (e.g. thinners, benzene, ink, make-up etc.). Use a soft, lint-free and dust-collecting rag (2) for cleaning. 38 G G G G 1 Do not use cleaning agents containing alcohol. Do not use cleaning and abrasive agents, as they may damage the display. 17.2.
18. TECHNICAL DATA The following table lists an overview of the most important technical data of your Evo control unit. Parameter Min. value Type value Unit +80 °C Temperature range storage -30 Temperature range operation -20 25 +60 °C Temperature range USB charging function -10 25 +40 °C Voltage range USB charging function 4.75 5.0 5.25 V 1.0 A 70 V Current USB charging function Supply voltage 40 Max. value 24 36 Protection class display IP65 Consumption active 1.
Industriestrasse 4 P.O. Box 159 CH-9473 Gams SWITZERLAND info@go-swissdrive.com www.go-swissdrive.
