FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\title.fm D E L L C O N F I D E N T I A L – P R E L I M I N A R Y 7 / 2 2 / 0 8 – F O R P R O O F O N LY Template Last Updated - 2/21/2007 Dell™ E-Flat Panel Stand User’s Guide w w w. d e l l . c o m | s u p p o r t . d e l l .
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2008 Dell Inc.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\bookTOC.fm Contents 1 About Your Dell™ E-Flat Panel Stand . . . . 5 2 Using the E-Flat Panel Stand . . . . . . . . . . . 7 . . . . . . 7 . . . 8 . 9 Connecting the Riser to the Base of the Stand Adjusting the Weight Limit for a Flat Panel Monitor Attaching a Flat Panel Monitor to the Flat Panel Stand Using a VESA Adapter Plate . . . . . . . . . . . . . . . 10 . . . . . . . . . . . . 14 .
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\bookTOC.
About Your Dell™ E-Flat Panel Stand The Dell™ E-Flat panel stand supports the following: • 12.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\about.
Using the E-Flat Panel Stand Connecting the Riser to the Base of the Stand 1 Align the front of the riser with the attachment slot. 2 Slide the riser into the attachment slot. You hear a click when the riser is completely engaged with the base of the stand.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm Adjusting the Weight Limit for a Flat Panel Monitor The default weight limit for the flat panel monitor is set for a 17-inch to 20inch monitor. If your monitor is 20 inches to 24 inches, adjust the weight limit setting on the flat panel stand. 1 Remove the tool from the base of the flat panel stand. 2 Insert the tool into the weight limit slot.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm Attaching a Flat Panel Monitor to the Flat Panel Stand 1 Align the back of the flat panel monitor with the attachment plate on the riser. 2 Slide the flat panel monitor onto the attachment plate, ensuring that the monitor is securely set in place.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm Using a VESA® Adapter Plate NOTE: The VESA adapter plate is optional. See Dell.com for purchasing information. Use a VESA adapter plate to attach your monitor to the flat panel stand if your monitor does not work with the attachment plate. 1 Remove the four screws from the attachment plate on the flat panel stand.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm 2 Install the VESA adapter plate with the four screws that came with the adapter plate. 2 1 3 1 screws (4) 3 flat panel stand 2 VESA adapter plate NOTE: Different standards may apply to different flat panel monitors. See the documentation that came with your monitor if you find the following information does not work for your monitor.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm If your monitor is 15 inches or smaller: a Use the four holes that are closer to the center of the VESA adapter plate (diameter measures 75 mm x 75 mm between the holes). b Insert the caps in the other four holes on the VESA adapter plate. c Attach your monitor to the VESA adapter plate.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm If your monitor is larger than 15 inches: a Use the four holes closer to the outer edge of the VESA adapter plate (diameter measures 100 mm x 100 mm between the holes). b Insert the caps into the other four holes on the VESA adapter plate. c Attach your monitor to the VESA adapter plate.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm 1 caps (4) 2 VESA adapter plate 3 screw holes for monitor larger than 15 inches (4) 4 flat panel monitor 5 flat panel stand Adjusting the Flat Panel Monitor NOTICE: If you have a laptop docked in the flat panel stand, angle the monitor up and ensure it is clear of your laptop before you change the monitor from landscape to portrait orientation.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm Connecting a Port Replicator to the Flat Panel Stand 1 With the front of the port replicator raised slightly, slide the port replicator toward the back of flat panel stand until the port replicator rests against the guide posts. 2 Push down on the port replicator to secure it to the release tab on the flat panel stand.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm 3 Follow the procedures for setting up your port replicator. See the E-Port User’s Guide or the E-Port Plus User’s Guide that shipped with your port replicator or on support.dell.com. Disconnecting a Laptop From the Port Replicator and Flat Panel Stand 1 Push the eject button on the side of the port replicator. 2 Lift the laptop away from the port replicator and flat panel stand.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\using.fm Disconnecting a Port Replicator From the Flat Panel Stand 1 Disconnect all cables from the port replicator. 2 Press the release button on the back of the flat panel stand, and then lift the front of the port replicator to release it from the release tab on the flat panel stand. 3 Remove the port replicator from the flat panel stand.
Specifications Physical Height 245 mm (9.65 inches) Depth 410 mm (16.14 inches) Width 375 mm (14.76 inches) Weight 3.5 kg (7.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\spec.
Finding Information Documents Contents Safety, Regulatory, Warranty, and Support • Warranty information Documentation • Terms and Conditions (U.S. only) This type of information may have • Safety instructions shipped with your computer. For additional regulatory information, see the • Regulatory information Regulatory Compliance Homepage on • Ergonomics information www.dell.com at the following location: • End User License Agreement www.dell.com/regulatory_compliance.
FILE LOCATION: C:\Documents and Settings\julie_Woodson\My Documents\eDocs\Edocks\efpl\en\Source\findinfo.