Manualshelf

Reference Guide

ManualsBrandsDell ManualsComputer equipmentNetworking Z9500
191192193194195196197198199200
v6 VRRP Q15 RP 400 400 2000 2000
MLD Q14 RP 150 150 500 500
v6 MULTICAST Q9 RP 100 100 500 500
CATCH ALL
v6 ICMP NA Q3/Q11 CP/RP 600 600 1000 1000
v6 ICMP RA Q3/Q11 CP/RP 600 600 1000 1000
v6 ICMP NS Q2/Q10 CP/RP 600 600 1000 1000
v6 ICMP RS Q2/Q10 CP/RP 600 600 1000 1000
v6 ICMP Q5 CP 300 300 2000 2000
BGP Q15 RP 2500 2500 2000 2000
OSPF Q15 RP 2500 2500 2000 2000
RIP Q15 RP 200 200 1000 1000
VRRP Q15 RP 400 400 2000 2000
ICMP Q6 CP 300 300 2000 2000
IGMP Q14 RP 300 300 2000 2000
PIM Q14 RP 300 300 2000 2000
MSDP Q14 RP 100 100 2000 2000
BFD Q13/Q21 RP/LP 7000 7000 3000 3000
802.1x Q7 CP 150 150 1000 1000
iSCSI Q9 RP 100 100 500 500
DHCP RELAY Q7 CP 1200 1200 2000 2000
DHCP Q7 CP 1200 1200 2000 2000
NTP Q4 CP 200 200 2000 2000
FTP Q4 CP 400 400 3000 3000
TELNET Q4 CP 400 400 2000 2000
SSH Q4 CP 400 400 2000 2000
VLT CTRL Q12 RP 2000 2000 3000 3000
VLT IPM PDU Q4/Q12 CP/RP 500 500 3000 3000
VLT TTL1 Q0 CP 100 100 500 500
HYPERPULL Q22 LP 500 500 1000 1000
OPENFLOW Q14 RP 300 300 1000 1000
FEFD Q7 CP 150 150 1000 1000
TRACEFLOW Q20 LP 200 200 500 500
FCoE Q14 RP 300 300 2000 2000
SFLOW Q23 LP 5000 5000 3000 3000
L3 LOCAL TERMINATED Q4 CP 400 400 5000 5000
L3 UNKNOWN/ Q8 RP 200 200 3000 3000
UNRESOLVED ARP
L2 DST HIT/ Q0/Q8 CP/RP 200 200 500 500
BROADCAST
MULTICAST CATCH ALL Q9 RP 200 200 500 500
ACL LOGGING Q20 LP 200 200 1000 1000
L3 HEADER ERROR/TTL0 Q0 CP 200 200 500 500
IP OPTION/TTL1 Q0 CP 100 100 500 500
VLAN L3 MTU FAIL Q1 CP 200 200 500 500
Physical L3 MTU FAIL Q1 CP 200 200 500 500
ICMP REDIRECT Q1 CP 200 200 500 500
SOURCE MISS Q20 LP 200 200 500 500
STATION MOVE Q20 LP 200 200 500 500
Troubleshooting CoPP Operation
To troubleshoot CoPP operation, use the debug commands described in this section.
Enabling CPU Traffic Statistics
During high-traffic network conditions, you may want to manually enable the collection of CPU traffic statistics by entering the
debug cpu-traffic-stats command. Statistic collection begins as soon as you enter the command, not when the system
boots up.
The following message is displayed when the collection of CPU traffic statistics is enabled. Use the show cpu-traffic-
stats command to view the statistics.
Excessive traffic is received by CPU and traffic will be rate controlled.
194
Control Plane Policing (CoPP)