Reference Guide

Display Transceiver Type
To monitor the types of transceivers installed in switch ports, use the show inventory media command.
Use the command output to verify the type of QSFP transceiver installed in a port when Syslog messages are displayed
following the removal or insertion of a QSFP transceiver:
Apr 2 22:28:43: %Z9500LC48:1 %IFAGT-5-INSERT_OPTICS_QSFP: Optics QSFP
When you configure a 40GbE QSFP+ port to operate in quad (4x10GbE) mode as four 10GbE SFP+ ports, a Syslog message is
displayed for each 10GbE port.
Apr 2 22:28:38: %Z9500LC48:1 %IFAGT-5-REMOVED_OPTICS_QSFP: Optics
QSFP removed in slot 1 port 140
Apr 2 22:28:38: %Z9500LC48:1 %IFAGT-5-REMOVED_OPTICS_QSFP: Optics QSFP removed
in slot 1 port 141
Apr 2 22:28:38: %Z9500LC48:1 %IFAGT-5-REMOVED_OPTICS_QSFP: Optics QSFP removed
in slot 1 port 142
Apr 2 22:28:38: %Z9500LC48:1 %IFAGT-5-REMOVED_OPTICS_QSFP: Optics QSFP removed
in slot 1 port 143
To verify the transceiver plugged into a Z9500 port, use the show inventory media command.
Dell#show inventory media
Slot Port Type Media Serial Number
F10Qualified
-----------------------------------------------------------------------------------------
--
2 0 QSFP 40GBASE-CR4-1M APF12380010GM4 Yes
2 4 Media not present or accessible
2 8 Media not present or accessible
2 12 Media not present or accessible
2 16 QSFP 40GBASE-SR4 7503825D0169 Yes
2 20 Media not present or accessible
2 24 QSFP 40GBASE-CR4-1M APF12380010GM4 Yes
2 28 Media not present or accessible
2 32 Media not present or accessible
2 36 Media not present or accessible
2 40 QSFP 40GBASE-SR4 7503825H006J Yes
2 44 Media not present or accessible
To display more detailed information about the transceiver type, wavelength, and power reception on a Z9500 port, use the
show interfaces command.
Dell#show interfaces fortyGigE 2/16
fortyGigE 2/16 is down, line protocol is down
Hardware is DellForce10Eth, address is 00:02:e5:c1:00:c2
Current address is 00:02:e5:c1:00:c2
Pluggable media present, QSFP type is 40GBASE-SR4
Wavelength is 850nm
QSFP receive power reading is 0.3145dBm
Interface index is 155337218
Internet address is not set
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed 40000 Mbit
Flowcontrol rx off tx off
To display more diagnostic data when troubleshooting a transceiver, use the show interfaces tranceiver command.
Additional information about QSFP temperature, voltage, and current alarm thresholds are displayed.
Dell#show interfaces fortyGigE 2/168 transceiver
QSFP 168 Serial ID Base Fields
QSFP 168 Id = 0x0d
QSFP 168 Ext Id = 0xc0
QSFP 168 Connector = 0x07
QSFP 168 Transceiver Code = 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0x00
QSFP 168 Encoding = 0x05
256
Debugging and Diagnostics