Reference Guide

The following example shows no change in the updated packets (shown in bold). ACKs 2 (shown in bold) is printed only for ACK
packets.
00:10:41 : OSPF(1000:00):
Rcv. v:2 t:5(LSAck) l:64 Acks 2 rid:2.2.2.2
aid:1500 chk:0xdbee aut:0 auk: keyid:0 from:Vl 1000
LSType:Type-5 AS External id:160.1.1.0 adv:6.1.0.0 seq:0x8000000c
LSType:Type-5 AS External id:160.1.2.0 adv:6.1.0.0 seq:0x8000000c
00:10:41 : OSPF(1000:00):
Rcv. v:2 t:5(LSAck) l:64 Acks 2 rid:2.2.2.2
aid:1500 chk:0xdbee aut:0 auk: keyid:0 from:Vl 100
LSType:Type-5 AS External id:160.1.1.0 adv:6.1.0.0 seq:0x8000000c
LSType:Type-5 AS External id:160.1.2.0 adv:6.1.0.0 seq:0x8000000c
00:10:41 : OSPF(1000:00):
Rcv. v:2 t:4(LSUpd) l:100 rid:6.1.0.0
aid:0 chk:0xccbd aut:0 auk: keyid:0 from:Te 10/21
Number of LSA:2
LSType:Type-5 AS External(5) Age:1 Seq:0x8000000c id:170.1.1.0 Adv:6.1.0.0
Netmask:255.255.255.0 fwd:0.0.0.0 E2, tos:0 metric:0
LSType:Type-5 AS External(5) Age:1 Seq:0x8000000c id:170.1.2.0 Adv:6.1.0.0
Netmask:255.255.255.0 fwd:0.0.0.0 E2, tos:0 metric:0
To confirm that you enabled RFC-2328–compliant OSPF flooding, use the show ip ospf command.
Dell#show ip ospf
Routing Process ospf 1 with ID 2.2.2.2
Supports only single TOS (TOS0) routes
It is an Autonomous System Boundary Router
It is Flooding according to RFC 2328
SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
Number of area in this router is 1, normal 0 stub 0 nssa 1
--More--
OSPF ACK Packing
The OSPF ACK packing feature bundles multiple LS acknowledgements in a single packet, significantly reducing the number of
ACK packets transmitted when the number of LSAs increases.
This feature also enhances network utilization and reduces the number of small ACK packets sent to a neighboring router. OSPF
ACK packing is enabled by default and non-configurable.
Setting OSPF Adjacency with Cisco Routers
To establish an OSPF adjacency between Dell Networking and Cisco routers, the hello interval and dead interval must be the
same on both routers.
The OSPF dead interval value is, by default, set to 40 secondsand is independent of the OSPF hello interval. Configuring a hello
interval does not change the dead interval in the system. In contrast, the OSPF dead interval on a Cisco router is, by default,
four times as long as the hello interval. Changing the hello interval on the Cisco router automatically changes the dead interval.
To ensure equal intervals between the routers, use the following command.
● Manually set the dead interval of the Dell Networking router to match the Cisco configuration.
INTERFACE mode
ip ospf dead-interval <x>
In the following example, the dead interval is set at 4x the hello interval (shown in bold).
Dell(conf)#int te 2/2
Dell(conf-if-te-2/2)#ip ospf hello-interval 20
Dell(conf-if-te-2/2)#ip ospf dead-interval 80
Dell(conf-if-te-2/2)#
528
Open Shortest Path First (OSPFv2 and OSPFv3)