53-1001799-01 January 31, 2010 PowerConnect B-DCX-4S Rack Mount Kit Installation Procedure Supporting PowerConnect B-DCX-4S Backbone 53-1001799-01 *53-1001799-01*
Notes, Cautions, and Warnings NOTE A NOTE indicates important information that helps you make better use of your computer. CAUTION See the safety and regulatory information that shipped with your system. For additional regulatory information, see the Regulatory Compliance Homepage on www.dell.com at the following location: www.dell.com/regulatory_compliance. CAUTION A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
In this guide • Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Installing the DCX-4S in equipment cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . • Unpacking the PowerConnect B-DCX-4S. . . . . . .
• Ensure that one or two dedicated electrical branch circuits with the following characteristics are available: - 200-240 VAC, 50-60 Hz (refer to the corresponding Hardware Reference Manual for additional electrical specifications). - Protected by a circuit breaker in accordance with local electrical codes. - Grounded outlets are installed by a licensed electrician and compatible with the power cords.
Parts list The following parts list refers to items illustrated in Figure 1. TABLE 1 Item Items supplied with the DCX-4S rack mount kit Description For all types of installations A Left rail B Right rail C 10-32 x .5 in. (1.27 cm) Phillips screw D 10-32 x .63 in.(1.60 cm) Phillips screw. with square cone washer for cabinets that have rails with round holes. E Alignment washer for cabinets that have rails with square holes. FIGURE 1 DCX-4S 27 to 31 in. (68.58 to 78.
Unpacking the PowerConnect B-DCX-4S Use the following procedure to unpack the PowerConnect B-DCX-4S. CAUTION Use safe lifting practices when moving the product. (C015) NOTE A fully populated PowerConnect B-DCX-4S weighs 103.50 kg (228.20 lb) with four FC8-48 port cards installed (192 ports) and requires a hydraulic or assisted lift to install it. 1. Unpack the PowerConnect B-DCX-4S. a. Cut the bands that encircle the packaging. b. Remove the lid and the kits and foam from the top of the chassis. c.
FIGURE 2 DCX-4S rails installed in equipment cabinet Install DCX-4S in cabinet 1. Ensure that the door is removed from the port side of the DCX-4S. For instructions, refer to the DCX-4S Backbone Hardware Reference Manual. 2. Ensure the chassis can be oriented so that the nonport side has access to intake air (cool). 3. Use a lift to raise the chassis to the correct level. CAUTION Use safe lifting practices when moving the product. (C015) 4. If applicable, lock the wheels of the lift. 5.
FIGURE 3 Installing DCX-4S into equipment cabinet 6. Secure the DCX-4S to the equipment cabinet racks with six 10-32 screws with square-cone washers (D in Figure 1 on page 5), three screws on each side. Tighten screws to 32 in.-lbs (36.86 cm-kg). NOTE Screws, clip nuts, and retainer nuts for the DCS-4S are included in the DCX-4S hardware accessory kit.
NOTE For rails with round holes, use the clip nuts on the cabinet rails for securing 10-32 screws. For rails with square holes, use the retainer nuts. Refer to Figure 5 on page 9. FIGURE 5 7. Using clip nuts and retainer nuts to secure screws to cabinet rails Install the DCX-4S door and required cable management system using instructions in the DCX-4S Backbone Hardware Reference Manual.
PowerConnect B-DXC-4S Rack Mount Kit Installation Procedure 53-1001799-01