Quick Reference Guide

488 PowerConnect B-Series TI24X Configuration Guide
53-1002269-02
PIM Sparse
19
RP 2 Configuration
The following commands provide the configuration for the RP 2 router in .Figure 88.
RP2(config)#router ospf
RP2(config-ospf-router)# area 0
RP2(config-ospf-router)# exit
RP2(config)# interface loopback 1
RP2(config-lbif-1)# ip ospf area 0
RP2(config-lbif-1)# ip ospf passive
RP2(config-lbif-1)# ip address 100.1.1.2/32
RP2(config-lbif-1)# exit
RP2(config)# interface loopback 2
RP2(config-lbif-2)# ip ospf area 0
RP2(config-lbif-2)# ip ospf passive
RP2(config-lbif-2)# ip address 100.2.1.1/32
RP2(config-lbif-2)# ip pim-sparse
RP2(config-lbif-2)# exit
RP2(config)# interface ethernet 1
RP2(config-if-e10000-1)# ip ospf area 0
RP2(config-if-e10000-1)# ip ospf cost 2
RP2(config-if-e10000-1)# ip address 192.1.1.2/24
RP2(config-if-e10000-1)# ip pim-sparse
RP2(config)# interface ethernet 3
RP2(config-if-e10000-3)# ip ospf area 0
RP2(config-if-e10000-3)# ip ospf cost 2
RP2(config-if-e10000-3)# ip address 192.2.1.2/24
RP2(config-if-e10000-3)# ip pim-sparse
RP2(config-if-e10000-3)# exit
RP2(config)# router pim
RP2(config-pim-router)# rp-address 100.2.1.1
RP2(config-pim-router)# exit
RP2(config)# router msdp
RP2(config-msdp-router)# msdp-peer 100.1.1.1 connect-source loopback 1
RP2(config-msdp-router)# msdp-peer 100.1.1.3 connect-source loopback 1
RP2(config-msdp-router)# mesh-group mesh1 100.1.1.1
RP2(config-msdp-router)# mesh-group mesh1 100.1.1.3
RP2(config-msdp-router)# originator-id loopback 1
RP2(config-msdp-router)# exit
RP2(config)#ip router-id 100.1.1.2
RP 3 Configuration
The following commands provide the configuration for the RP 3 router in Figure 88.
RP3(config)#router ospf
RP3(config-ospf-router)# area 0
RP3(config-ospf-router)# exit
RP3(config)# interface loopback 1
RP3(config-lbif-1)# ip ospf area 0
RP3(config-lbif-1)# ip ospf passive
RP3(config-lbif-1)# ip address 100.1.1.3/32
RP3(config-lbif-1)# exit
RP3(config)# interface loopback 2
RP3(config-lbif-2)# ip ospf area 0
RP3(config-lbif-2)# ip ospf passive
RP3(config-lbif-2)# ip address 100.2.1.1/32
RP3(config-lbif-2)# ip pim-sparse
RP3(config-lbif-2)# exit
RP3(config)# interface ethernet 3
RP3(config-if-e10000-3)# ip ospf area 0
RP3(config-if-e10000-3)# ip ospf cost 2