Dell™ PowerEdge™ 1850 Systems Information Update 信息更新 Mise à jour des informations Aktuelle Informationen アップデート情報 정보 업데이트 Actualización de información w w w. d e l l . c o m | s u p p o r t . d e l l .
Dell™ PowerEdge™ 1850 Systems Information Update w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Abbreviations and Acronyms For a complete list of abbreviations and acronyms, see "Glossary" in your User’s Guide.
This document provides updated information for your system on the following topics: • Enabling video hardware acceleration in the Microsoft® Windows® Server 2003 operating system • Correcting flat-panel display video problems during Microsoft Windows Server 2003 operating system installations • NIC teaming limitations • Failure to load usb-ohci driver message on systems running Red Hat® Enterprise Linux (version 2.
www.dell.com | support.dell.com Console redirection is intended for system management from a terminal attached to the system’s serial port. When Windows Server 2003 detects that console redirection is enabled, it optimizes its installation screens to a low-resolution text mode for a vt100-compatible terminal. Some flat-panel displays cannot synchronize to that mode. To correct the problem, restart the system, enter the System Setup program, and disable console redirection.
Failure to Load usb-ohci Driver Message on Systems Running Red Hat Enterprise Linux (Version 2.1) A failure message may be displayed when Initializing USB controller (usb-ohci) appears during startup. Update versions of Red Hat Enterprise Linux (version 2.1) prior to Update 4 mistakenly attempt to load this driver for the USB 2.0 controller. Red Hat Enterprise Linux (version 2.1) does not support USB 2.0. To avoid this erroneous message on versions prior to Update 4, remove the line in /etc/modules.
www.dell.com | support.dell.com 6 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. a Open the system. b Remove all memory modules from the system. See "Removing Memory Modules" in your Installation and Troubleshooting Guide. c Replace one of the memory modules in socket DIMM1_B. d Close the system. e Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.
6 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals. If there is no memory-related error message, the problem is resolved. If the problem persists, see "Getting Help" in your Installation and Troubleshooting Guide. There are memory-related error messages in the SEL. 1 Enter the System Setup program and disable the Redundant Memory option, if applicable. See "Using the System Setup Program" in your User's Guide. 2 Run the appropriate online diagnostic test.
www.dell.com | support.dell.com System Memory Configurations The following table of sample memory configurations updates Table 6-1 in "Installing System Components" in your Installation and Troubleshooting Guide. Table 1-2.
Dell™ PowerEdge™ 1850 系统 信息更新 w w w. d e l l . c o m | s u p p o r t . d e l l .
注、注意和警告 注:注表示可以帮助您更好地使用计算机的重要信息。 注意:注意表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 警告:警告表示存在可能导致财产损失、人身伤害或死亡的潜在危险。 缩写词和缩略词 有关缩写词和缩略词的完整列表,请参阅 《用户指南》中的 “词汇表”。 ____________________ 本文中的信息如有更改,恕不另行通知。 © 2004 Dell Inc. 版权所有,翻印必究。 未经 Dell Inc. 书面许可,不得以任何方式进行复制。 本文中使用的商标:Dell、 PowerEdge 和 DELL 徽标是 Dell Inc. 的商标; Red Hat 是 Red Hat, Inc. 的注册商标; Microsoft 和 Windows 是 Microsoft Corporation 的注册商标; Novell 和 NetWare 是 Novell Corporation 的注册商标; Intel 是 Intel Corporation 的注册商标。 本文中述及的其他商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。 Dell Inc.
本说明文件针对您的系统提供了有关以下主题的更新信息: • 在 Microsoft® Windows® Server 2003 操作系统中启用视频硬件加速 • 纠正 Microsoft Windows Server 2003 操作系统安装过程中的平板显示屏视频问题 • NIC 组队限制 • 运行 Red Hat® Enterprise Linux (2.
www.dell.com | support.dell.com NIC 组队限制 如果将底板管理控制器 (BMC) 配置为使用第一个集成 NIC (NIC1) 访问系统, 在某些情况下,组队功能和 BMC 功能将受到影响,如表 2-1 中所示。 表 2-1. BMC 使用 NIC1 对组队功能造成的影响 操作 AFT、ALB/RLB 和 SFT 组队模式 IEEE 802.
系统内存信息 排除系统内存故障 以下步骤提供了进一步的系统内存故障排除说明。 问题 • 内存模块出现故障。 • 主板出现故障。 • 系统状态指示灯呈现琥珀色。 • 系统哔声代码指示出现内存问题。 • 系统管理软件发出与内存相关的信息。 操作 系统启动时发出与内存相关的哔声代码。 警告:只有经过培训的维修技术人员才有权卸下主机盖并拆装系统内部的任何组件。有关安全 预防措施、拆装计算机内部组件以及防止静电释放的详细信息,请参阅 《产品信息指南》。 1 关闭系统和连接的外围设备电源,然后断开系统与电源插座的连接。 2 打开系统外壳。请参阅《安装与故障排除指南》中的“打开系统外壳”。 3 在插槽中重新放置内存模块。请参阅《安装与故障排除指南》中的“安装内存模块”。 4 合上系统外壳。请参阅《安装与故障排除指南》中的“合上系统外壳”。 5 将系统重新连接到电源插座,然后打开系统和连接的外围设备电源。 如果没有发出与内存相关的哔声代码,则表明问题已得到解决。 6 关闭系统和连接的外围设备电源,然后断开系统与电源插座的连接。 a 打开系统外壳。 b 从系统中卸下所有内存模
www.dell.com | support.dell.
系统内存配置 下表的内存配置实例用于更新 《安装与故障排除指南》中 “安装系统组件”的表 6-1。 表 2-2.
2-8 信息更新 www.dell.com | support.dell.
Systèmes Dell™ PowerEdge™ 1850 Mise à jour des informations w w w. d e l l . c o m | s u p p o r t . d e l l .
Remarques, avis et précautions REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter le problème. PRÉCAUTION : une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle ou de mort.
Ce document contient des informations mises à jour portant sur les sujets suivants : • Activation de l'accélération matérielle vidéo sous Microsoft® Windows® Server 2003 • Correction des problèmes d'affichage vidéo sur écran plat lors de l'installation du système d'exploitation Microsoft Windows Server 2003 • Contraintes liées à la mise en équipe (“teaming”) de plusieurs NIC • Message indiquant l'échec du chargement du pilote usb-ohci sous Red Hat® Enterprise Linux (version 2.
www.dell.com | support.dell.com Correction des problèmes d'affichage vidéo sur écran plat lors de l'installation du système d'exploitation Microsoft Windows Server 2003 REMARQUE : les informations suivantes ne s'appliquent qu'aux systèmes Microsoft Windows Server 2003 connectés à certains types d'écrans plats. Elles ne s'appliquent pas aux systèmes connectés à un moniteur à tube cathodique ou fonctionnant sous d'autres systèmes d'exploitation.
Tableau 3-1. Effet produit sur la fonctionnalité de teaming en cas d'utilisation du NIC1 par le contrôleur BMC Action Modes de teaming AFT, ALB/RLB et SFT Mode de teaming IEEE 802.3ad et EtherChannel Effet Effet NIC1 alloué au contrôleur Fonctionnement normal du BMC après la création teaming et du contrôleur BMC. du team Fonctionnement normal du teaming. Le fonctionnement du contrôleur BMC peut être affecté par la perte du trafic de gestion.
www.dell.com | support.dell.com Informations sur la mémoire système Dépannage de la mémoire système La procédure suivante présente des techniques avancées pour le dépannage de la mémoire système. Problème • Module de mémoire défectueux. • Carte système défectueuse. • Le voyant d'état du système est orange. • Un code sonore du système indique un problème lié à la mémoire. • Le logiciel de gestion de systèmes a émis un message d'erreur concernant la mémoire.
e Rebranchez le système à la prise de courant et allumez-le, ainsi que les périphériques connectés. f Si le code sonore indiquant une erreur de mémoire ne retentit pas, le module mémoire n'est pas en cause. En revanche, si le code retentit de nouveau, le module est défectueux et doit être remplacé. 7 8 Effectuez les opérations suivantes : a Éteignez le système et les périphériques connectés, puis débranchez-le de la prise de courant. b Ouvrez le système.
www.dell.com | support.dell.com Le journal d'événements du système contient des messages indiquant une erreur liée à la mémoire. 1 Accédez au programme de configuration du système et désactivez l'option Redundant Memory (Mémoire redondante), le cas échéant. Voir la section “Utilisation du programme de configuration du système” dans le Guide d'utilisation. 2 Exécutez le test de diagnostic en ligne approprié.
Dell™ PowerEdge™ 1850-Systeme Aktuelle Informationen w w w. d e l l . c o m | s u p p o r t . d e l l .
Anmerkungen, Hinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, die Ihnen die Arbeit mit dem Computer erleichtern. HINWEIS: Ein HINWEIS warnt vor möglichen Beschädigungen der Hardware oder Datenverlust und zeigt, wie diese vermieden werden können. VORSICHT: VORSICHT zeigt eine potenziell gefährliche Situation an, die zu Sachschäden, Verletzungen oder zum Tod führen könnte.
Dieses Dokument enthält aktuelle Informationen zu Ihrem System. Es behandelt die folgenden Themen: • Aktivieren der Grafik-Hardwarebeschleunigung beim Betriebssystem Microsoft® Windows® Server 2003 • Anzeigeprobleme mit Flachbildschirmen bei der Installation des Betriebssystems Microsoft Windows Server 2003 • Beschränkungen von NIC-Teaming • Meldung „Failure to Load usb-ohci Driver“ (Treiber usb-ohci konnte nicht geladen werden) bei Systemen mit Red Hat® Enterprise Linux (Version 2.
www.dell.com | support.dell.com Anzeigeprobleme mit Flachbildschirmen bei der Installation des Betriebssystems Microsoft Windows Server 2003 ANMERKUNG: Die folgenden Informationen beziehen sich nur auf die Installation von Microsoft Windows Server 2003 bei Systemen, an denen bestimmte Flachbildschirme angeschlossen sind. Systeme mit Röhrenmonitor oder mit anderen Betriebssystemen sind nicht betroffen.
Tabelle 4-1. Wirkung auf die Teaming-Funktion durch Verwendung von NIC1 durch BMC Teaming-Modi AFT, ALB/RLB und SFT Teaming-Modi IEEE 802.3ad und Ether Channel Vorgang Wirkung Wirkung NIC1 wird BMC nach Bildung des Teams zugewiesen. Normale Teamingund BMC-Funktion. Normale Teaming-Funktion. BMCFunktion kann durch Verlust von Management-Traffic beeinträchtigt werden. BMC gibt eine Warnmeldung über den Verlust von Management-Traffic bei adaptivem Failover aus.
www.dell.com | support.dell.com Informationen zu Systemspeicher Beheben von Störungen beim Systemspeicher Der folgende Vorgang dient der verbesserten Fehlerbehebung beim Systemspeicher. Problem • Defektes Speichermodul. • Defekte Systemplatine. • Systemstatusanzeige leuchtet gelb. • Signaltoncode zeigt ein Speicherproblem an. • Die Systemverwaltungssoftware gibt eine speicherbezogene Fehlermeldung aus. Vorgang Speicherbezogener Signaltoncode beim Systemstart.
e Schließen Sie das System wieder an das Stromnetz an, und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. f Wenn kein speicherbezogener Signaltoncode zu hören ist, ist das Speichermodul intakt. Wenn der Signaltoncode wieder ertönt, ist das Speichermodul defekt und sollte ausgetauscht werden. 7 8 Führen Sie folgende Schritte durch: a Schalten Sie das System und die angeschlossenen Peripheriegeräte aus, und unterbrechen Sie die Stromzufuhr. b Öffnen Sie das System.
www.dell.com | support.dell.com Im Systemereignisprotokoll (SEL) sind speicherbezogene Fehlermeldungen vorhanden. 1 Rufen Sie das System-Setup-Programm auf, und deaktivieren Sie gegebenenfalls die Option Redundant Memory (Redundanter Speicher). Weitere Informationen finden Sie im Benutzerhandbuch unter „System-Setup-Programm verwenden“. 2 Führen Sie den entsprechenden Online-Diagnosetest durch. Siehe dazu „Verwenden von Server Administrator Diagnostics“ in der Anleitung zur Installation und Fehlersuche.
Dell™ PowerEdge™ 1850 システム アップデート情報 w w w. d e l l . c o m | s u p p o r t . d e l l .
メモ、注意、警告 メモ:操作上、知っておくと便利な情報が記載されています。 注意:ハードウェアの損傷やデータの損失の可能性があることを示し、その危険を回避するための方法を 説明しています。 警告:物的損害、けが、または死亡の原因となる可能性があることを示します。 略語について 略語の説明は、『ユーザーズガイド』の「用語集」を参照してください。 ____________________ 本書の内容は予告なく変更されることがあります。 © 2004 すべての著作権は Dell Inc. にあります。 Dell Inc. の書面による許可のない複製は、いかなる形態においても厳重に禁じられています。 本書で使用されている商標について:Dell、PowerEdge、および DELL ロゴは Dell Inc. の商標です。Red Hat は Red Hat, Inc.
本書では、以下のトピックについて、お使いのシステムに関するアップデート情報を提供 します。 • Microsoft® Windows® Server 2003 オペレーティングシステムでのビデオハードウェ アアクセラレータ機能の有効化 • Microsoft Windows Server 2003 オペレーティングシステムインストール時のフラッ トパネルディスプレイで発生するビデオ問題の修正 • NIC のチーミングの制限 • Red Hat® Enterprise Linux(バージョン 2.
www.dell.com | support.dell.
表 5-1 BMC が NIC1 を使用する場合のチーム化機能に対する影響 AFT、ALB/RLB、および SFT チー IEEE 802.
www.dell.com | support.dell.
e 電源ケーブルをコンセントに差し込んで、システムと周辺機器の電源を入れます。 f メモリに関連したビープコードが鳴動しなければメモリモジュールは正常です。 ビープコードが再び鳴動する場合はメモリモジュールに障害があり交換が必要です。 7 8 次の手順を実行します。 a システムおよび接続されている周辺機器の電源を切り、システムを電源コンセン トから外します。 b システムカバーを開きます。 c 取り付けてある各メモリモジュールについて、手順 6 の手順 c から f を繰り返し ます。 すべてのメモリモジュールをテストしても問題が解決しないか、またはどのメモリモ ジュールでもビープコードが鳴動する場合は、システム基板の不良です。『インス トール&トラブルシューティング』の「困ったときは」を参照してください。 システムは正常に起動するが、メモリに関連したエラーメッセージが発生する。 警告:システムのカバーを取り外して、システム内部に手を触れる作業は、トレーニングを 受けたサービス技術者の方だけが行ってください。安全上の注意、コンピュータ内部の作業、 および静電気障害への対処の詳細に
www.dell.com | support.dell.
Dell PowerEdge 1850 시스템 정보 업데이트 w w w. d e l l . c o m | s u p p o r t . d e l l .
주 , 주의사항 및 주의 참고: 주는 컴퓨터를 보다 효율적으로 사용할 수 있는 중요 정보를 제공합니다. 주의사항: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방 법을 알려줍니다. 주의: 주의는 위험한 상황, 심각한 부상 또는 사망할 우려가 있음을 알려줍니다. 약어 및 머리글자 약어 및 머리글자의 전체 목록은 사용 설명서의 " 용어집 " 을 참조하십시오 . ____________________ 본 설명서에 수록된 정보는 사전 통보 없이 변경될 수 있습니다. © 2004 Dell Inc. All rights reserved. Dell Inc.의 사전 승인 없이 어떠한 경우에도 무단 복제하는 것을 엄격히 금합니다. 본 설명서에 사용된 상표: Dell, PowerEdge 및 DELL 로고는 Dell Inc.의 상표입니다. Red Hat는 Red Hat, Inc.의 등록 상표입니다.
본 설명서에는 시스템에 대해 다음 항목의 업데이트 정보를 제공합니다. • Microsoft® Windows® Server 2003 운영 체제에서 비디오 하드웨어 가속 사용 • Microsoft Windows Server 2003 운영 체제 설치 중 평면 디스플레이 비디오 문제점 수정 • NIC 팀 제한사항 • Red Hat® Enterprise Linux(버전 2.1)를 실행하는 시스템에 usb-ochi 드라이버 메시지를 로 드하지 못함 • 시스템 메모리 정보 Microsoft Windows Server 2003 운영 체제에서 비디오 하드 웨어 가속 사용 기본적으로 비디오 하드웨어 가속은 Microsoft Windows Server 2003 운영 체제에서 낮은 설정 으로 설정합니다. 시스템의 비디오 제어기에서 고급 기능을 지원하고 비디오 하드웨어 가속을 가장 높은(최상) 설정으로 설정하도록 요구합니다.
www.dell.com | support.dell.com 문제점을 수정하려면 시스템을 다시 시작하고 시스템 설치 프로그램에 들어가서 콘솔 재지정 을 비활성화하십시오. Windows Server 2003 운영 체제를 설치한 후 시스템 설치 프로그램으로 들어가서 원할 경우 콘솔 재지정을 활성화하십시오. NIC 팀 제한사항 첫 번째 통합된 NIC (NICI)를 사용하는 시스템을 액세스하기 위해 BMC(보드 관리 컨트롤러)를 구성할 경우 표 표 6-1 표시된 것처럼 특정한 상황에서 팀 기능과 BMC 기능이 영향을 받습니다. 표 6-1. BMC 의 영향 팀 기능에서 NIC1 사용 AFT, ALB/RLB 및 SFT 팀 모드 IEEE 802.3ad 및 이더 채널 팀 모드 조치 영향 영향 팀이 만들어지기 전에 NIC1이 BMC에 할당됨 일반 팀 및 BMC 기능 정상적인 팀 기능. 관리 트래픽의 손실 때문에 BMC 기능이 영향을 받을 수 있 습니다.
Red Hat Enterprise Linux( 버전 2.1) 를 실행하는 시스템에 usb-ochi 드라이버 메시지를 로드하지 못함 시작 중에 USB 컨트롤러(usb-ohci) 초기화 중이 나타날 때 실패 메시지가 표시될 수 있습 니다. Red Hat Enterprise Linux(버전 2.1) 업데이트 4 이전의 업데이트 버전에서 USB 2.0 컨트롤 러에 대해 이 드라이버를 잘못 로드하려고 합니다. Red Hat Enterprise Linux(버전 2.1)에서는 USB 2.0을 지원하지 않습니다. 업데이트 4 이전의 버전에서 이러한 오류 메시지를 방지하려면 usb-ohci를 로드시키는 /etc/modules.conf의 행을 제거하십시오. 그렇지 않으면 Red Hat Enterprise Linux(버전 2.1) 업데이트 4를 설치하여 문제를 해결하십시오. 시스템 메모리 정보 시스템 메모리 문제 해결 다음 절차에서는 개선된 시스템 메모리 문제 해결 방법을 제공합니다. 문제 • 결함있는 메모리 모듈.
www.dell.com | support.dell.com 6 시스템과 연결된 주변 장치의 전원을 끄고 시스템을 전기 콘센트에서 분리하십시오. a 시스템을 여십시오 . b 시스템에서 모든 메모리 모듈을 제거하십시오 . 설치 및 문제 해결 설명서의 " 메모리 모듈 제거 " 를 참조하십시오 . c 소켓 DIMM1_B 의 메모리 모듈 중 하나를 교체하십시오 . d 시스템을 닫으십시오 . e 시스템을 전기 콘센트에 다시 연결하고 시스템과 연결된 주변 장치를 켜십시오 . f 메모리 관련 경고 코드가 없으면 메모리 모듈에 결함이 없습니다 . 경고 코드가 다시 발생하면 메모리 모듈이 결함이 있으므로 교체해야 합니다 . 7 8 다음 단계를 수행하십시오: a 시스템과 연결된 주변 장치의 전원을 끄고 시스템을 전기 콘센트에서 분리하십시오 . b 시스템을 여십시오 . c 설치된 모든 메모리 모듈에 대해 단계 6 의 단계 c 에서 단계 f 까지 반복하십시오 .
SEL 에 메모리 관련 오류 메시지가 있습니다 . 1 시스템 설치 프로그램에 들어가서 중복 메모리 옵션을 비활성화하십시오. 사용자 설명서 의 "시스템 설치 프로그램 사용"을 참조하십시오. 2 해당하는 온라인 진단 테스트를 실행하십시오. 설치 및 문제 해결 설명서의 "서버 관리자 진단 사용"을 참조하십시오. 3 진단에서 식별된 메모리 모듈을 교체하십시오. 설치 및 문제 해결 설명서의 "메모리 모듈 설치"를 참조하십시오. 4 시스템 설치 프로그램에 들어가서 단계 1에서 비활성화한 중복 메모리 옵션을 활성화하 십시오. 5 시스템을 재시작하십시오. SEL에 계속 메모리 관련 오류가 있으면 설치 및 문제 해결 설 명서의 "도움말 얻기"를 참조하십시오. 시스템 메모리 구성 샘플 메모리 구성의 다음 표가 설치 및 문제 해결 설명서의 "시스템 구성 요소 설치"에 있는 표 6-1을 업데이트합니다. 표 6-2.
6-8 정보 업데이트 www.dell.com | support.dell.
Sistemas Dell™ PowerEdge™ 1850 Actualización de información w w w. d e l l . c o m | s u p p o r t . d e l l .
Notas, avisos y precauciones NOTA: una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. AVISO: un AVISO indica la posibilidad de daños en el hardware o la pérdida de datos, e informa de cómo evitar el problema. PRECAUCIÓN: una PRECAUCIÓN indica el riesgo de daños en la propiedad, lesiones corporales o incluso la muerte. Abreviaturas y siglas Para ver una lista completa de las abreviaturas y las siglas, consulte el glosario de la Guía del usuario.
En este documento se proporciona información actualizada sobre el sistema con respecto a los siguientes temas: • Activación de la aceleración del hardware de vídeo en el sistema operativo Microsoft® Windows® Server 2003 • Corrección de problemas de vídeo en pantallas planas durante la instalación del sistema operativo Microsoft Windows Server 2003 • Limitaciones de la agrupación de NIC • Mensaje de error al cargar el controlador usb-ohci en sistemas que ejecutan Red Hat® Enterprise Linux (versión 2.
www.dell.com | support.dell.com Corrección de problemas de vídeo en pantallas planas durante la instalación del sistema operativo Microsoft Windows Server 2003 NOTA: la información siguiente sólo se aplica a las instalaciones del sistema operativo Microsoft Windows Server 2003 en sistemas que tienen conectadas determinadas pantallas planas. Dicha información no afecta a los sistemas que tienen un monitor CRT conectado ni a los sistemas que tienen instalado otro sistema operativo.
Tabla 7-1. Efecto del uso de la NIC1 por parte de la BMC en el funcionamiento de la agrupación Modo de agrupación SFT, ALB/RLB y AFT Modo de agrupación Ether Channel e IEEE 802.3ad Acción Efecto Efecto NIC1 asignada a BMC después de crear la agrupación Funcionamiento normal de la agrupación y de la BMC. Funcionamiento normal de la agrupación. El funcionamiento de la BMC puede verse afectado debido a la pérdida de tráfico de administración.
www.dell.com | support.dell.com Información de la memoria del sistema Solución de problemas de la memoria del sistema En el procedimiento siguiente se proporcionan instrucciones mejoradas de solución de problemas de la memoria del sistema. Problema • El módulo de memoria es defectuoso. • La placa base es defectuosa. • El indicador de estado del sistema se ilumina en color ámbar. • Un código de sonido del sistema indica que hay un problema con la memoria.
e Vuelva a conectar el sistema a la toma eléctrica y, a continuación, encienda el sistema y los periféricos conectados a éste. f Si no se emite ningún código de sonido relativo a la memoria, el módulo de memoria no es defectuoso. Si se emite un código de sonido, el módulo es defectuoso y se debe cambiar. 7 8 Lleve a cabo los pasos siguientes: a Apague el sistema y los periféricos conectados y desconecte el sistema de la toma eléctrica. b Abra el sistema.
www.dell.com | support.dell.com Hay mensajes de error relativos a la memoria en el registro de eventos del sistema (SEL) 1 Abra el programa de configuración del sistema y desactive la opción de memoria redundante, si procede. Consulte “Uso del programa de configuración del sistema” en la Guía del usuario. 2 Ejecute la prueba de diagnóstico en línea adecuada. Consulte “Uso de los diagnósticos de Server Administrator” en la Guía de instalación y solución de problemas.