CLI Guide

ManualsBrandsDell ManualsComputer HardwarePowerEdge T430

iDRAC 8/7 v2.70.70.70 RACADM CLI Guide

Summary of content (528 pages)

PAGE 1
iDRAC 8/7 v2.70.70.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents 1 Introduction............................................................................................................................... 33 New in this release.............................................................................................................................................................. 33 Supported RACADM Interfaces........................................................................................................................................
PAGE 4
getsensorinfo........................................................................................................................................................................72 getssninfo............................................................................................................................................................................. 75 getsvctag....................................................................................................................................
PAGE 5
vflashsd................................................................................................................................................................................ 151 vflashpartition.....................................................................................................................................................................152 vmdisconnect...............................................................................................................................
PAGE 6
cfgSessionManagement................................................................................................................................................... 168 cfgSsnMgtRacadmTimeout (Read or Write)........................................................................................................... 168 cfgSsnMgtConsRedirMaxSessions (Read or Write)...............................................................................................168 cfgSsnMgtWebserverTimeout (Read or Write).....
PAGE 7
cfgServerInfo...................................................................................................................................................................... 181 cfgServerName (Read Or Write)................................................................................................................................181 cfgServerNic3MacAddress (Read Only)...................................................................................................................
PAGE 8
cfgThermalEnhancedCoolingMode (Read or Write)............................................................................................... 193 cfgIpmiSol........................................................................................................................................................................... 194 cfgIpmiSolEnable (Read or Write).............................................................................................................................
PAGE 9
cfgServerPowerLastDayMinTime (Read Only).......................................................................................................203 cfgServerPowerLastDayMaxPower (Read Only)................................................................................................... 204 cfgServerPowerLastDayMaxTime (Read Only)......................................................................................................204 cfgServerPowerLastWeekMinPower (Read Only)................................
PAGE 10
cfgIPv6StaticGateway (Read or Write)....................................................................................................................215 cfgIPv6StaticPrefixLength (Read or Write).............................................................................................................215 cfgIPv6StaticAutoConfig (Read/Write)...................................................................................................................
PAGE 11
cfgLoggingSELOEMEventFilterEnable (Read or Write)........................................................................................ 226 cfgRacSecurity.................................................................................................................................................................. 226 cfgRacSecCsrCommonName (Read or Write).......................................................................................................
PAGE 12
System.Location.Chassis.Name (Read Only).......................................................................................................... 242 System.Location.Chassis.Slot (Read or Write)....................................................................................................... 242 System.OpenIDConnectServer....................................................................................................................................... 242 System.OpenIDConnectServer.
PAGE 13
System.Power.Supply.......................................................................................................................................................256 System.Power.Supply.CurrentDraw (Read Only)................................................................................................... 257 System.Power.Supply.FwVer (Read Only).............................................................................................................. 257 System.Power.Supply.[i].
PAGE 14
LifecycleController.LCAttributes.UserProxyType (Read and Write)....................................................................270 LifecycleController.LCAttributes.UserProxyUserName (Read or Write).............................................................270 LifecycleController.LCAttributes.VirtualAddressManagementApplication (Read or Write).............................. 270 iDRAC.ActiveDirectory..........................................................................................................
PAGE 15
iDRAC.IOIDOpt.VirtualAddressPersistencePolicyNonAuxPwrd (Read or Write)................................................283 iDRAC.IPBlocking.............................................................................................................................................................. 283 iDRAC.IPBlocking.BlockEnable (Read or Write)......................................................................................................283 iDRAC.IPBlocking.FailCount (Read or Write)..................
PAGE 16
iDRAC.IPv6.Address2 (Read or Write).....................................................................................................................296 iDRAC.IPv6.Address3 (Read or Write).....................................................................................................................296 iDRAC.IPv6.Address4 (Read or Write)..................................................................................................................... 297 iDRAC.IPv6.Address5 (Read or Write)........
PAGE 17
iDRAC.Logging.SELOEMEventFilterEnable (Read or Write)................................................................................ 309 iDRAC.NIC..........................................................................................................................................................................309 iDRAC.NIC.Autoconfig (Read or Write)................................................................................................................... 309 iDRAC.NIC.
PAGE 18
iDRAC.RemoteHosts.SMTPServerIPAddress (Read or Write).............................................................................322 iDRAC.RFS......................................................................................................................................................................... 323 iDRAC.RFS.IgnoreCertWarning (Read or Write).................................................................................................... 323 iDRAC.RFS.MediaAttachState (Read Only).........
PAGE 19
iDRAC.ServiceModule.WMIInfo (Read or Write).................................................................................................... 335 iDRAC.SmartCard............................................................................................................................................................. 335 iDRAC.SmartCard.SmartCardCRLEnable (Read or Write)....................................................................................336 iDRAC.SmartCard.
PAGE 20
iDRAC.USB.PortStatus (Read or Write).................................................................................................................. 347 iDRAC.Telnet.Timeout (Read or Write).................................................................................................................... 347 iDRAC.UserDomain........................................................................................................................................................... 348 iDRAC.UserDomain.
PAGE 21
iDRAC.VirtualMedia.KeyEnable (Read or Write).....................................................................................................360 iDRAC.VNCServer............................................................................................................................................................ 360 iDRAC.VNCServer.Enable (Read or Write)............................................................................................................. 360 iDRAC.VNCServer.
PAGE 22
BIOS.IntegratedDevices.InternalSdCardRedundancy (Read or Write)................................................................ 374 BIOS.IntegratedDevices.InternalUsb (Read or Write)............................................................................................ 374 BIOS.IntegratedDevices.InternalUsb1 (Read or Write)...........................................................................................374 BIOS.IntegratedDevices.InternalUsb2 (Read or Write)....................................
PAGE 23
BIOS.ProcSettings............................................................................................................................................................ 388 BIOS.ProcSettings.CorePerfBoost (Read or Write)...............................................................................................388 BIOS.ProcSettings.DataReuse (Read or Write)......................................................................................................388 BIOS.ProcSettings.
PAGE 24
BIOS.ProcSettings.ProcX2Apic (Read or Write).................................................................................................... 402 BIOS.ProcSettings.QpiBandwidthPriority (Read or Write)....................................................................................403 BIOS.ProcSettings.QpiSpeed (Read or Write)........................................................................................................403 BIOS.ProcSettings.RtidSetting (Read or Write)..........................
PAGE 25
BIOS.SataSettings.SataPortHModel (Read Only)...................................................................................................416 BIOS.SataSettings.SataPortI (Read or Write)..........................................................................................................417 BIOS.SataSettings.SataPortICapacity (Read or Write).......................................................................................... 417 BIOS.SataSettings.SataPortIDriveType (Read or Write)..............
PAGE 26
BIOS.SysProfileSettings.Proc2TurboCoreNum (Read or Write)...........................................................................431 BIOS.SysProfileSettings.ProcC1E (Read or Write)..................................................................................................431 BIOS.SysProfileSettings.ProcCStates (Read or Write)......................................................................................... 432 BIOS.SysProfileSettings.ProcPwrPerf (Read or Write)...............................
PAGE 27
FC.FCDevice.PCIDeviceID (Read Only)................................................................................................................... 445 FC.FCTarget...................................................................................................................................................................... 446 FC.FCTarget.BootScanSelection (Read or Write)..................................................................................................446 FC.FCTarget.
PAGE 28
NIC.DCBSettings.EnhancedTransmissionSelection (Read Only)..........................................................................458 NIC.DCBSettings.PriorityFlowControl (Read Only)................................................................................................458 NIC.DeviceLevelConfig.....................................................................................................................................................458 NIC.DeviceLevelConfig.EVBModesSupport (Read Only).......
PAGE 29
NIC.IscsiFirstTgtParams.FirstTgtChapPwd (Password)........................................................................................ 471 NIC.IscsiFirstTgtParams.FirstTgtIpAddress (Read or Write)................................................................................. 471 NIC.IscsiFirstTgtParams.FirstTgtIpVer (Read or Write)........................................................................................ 472 NIC.IscsiFirstTgtParams.FirstTgtIscsiName (Read or Write).......................
PAGE 30
NIC.NICConfig.LegacyBootProto (Read or Write).................................................................................................485 NIC.NICConfig.LnkSpeed (Read or Write).............................................................................................................. 486 NIC.NICConfig.NumberVFAdvertised (Read or Write)..........................................................................................486 NIC.NICConfig.VLanId (Read or Write)...................................
PAGE 31
NIC.VndrConfigGroup.VirtWWPN (Read or Write)............................................................................................... 500 NIC.VndrConfigGroup.WWN (Read Only)...............................................................................................................500 NIC.VndrConfigGroup.WWPN (Read Only)............................................................................................................ 500 NIC.VndrConfigPage...................................................
PAGE 32
Storage.enclosure.BackplaneRequestedMode (Read or Write)............................................................................ 512 Storage.enclosure.BackplaneType (Read Only).......................................................................................................513 Storage.PhysicalDisk......................................................................................................................................................... 513 Storage.PhysicalDisk.
PAGE 33
1 Introduction This document provides information about the RACADM subcommands, supported RACADM interfaces, and property database groups and object definitions for the following: • • iDRAC for Blade Servers iDRAC on Rack and Tower Servers Most of the commands mentioned in this document are applicable for multi-generation servers. That is, the commands are applicable for iDRAC6, iDRAC7, and iDRAC8.
PAGE 34
• SSH or Telnet — Also known as Firmware RACADM. Firmware RACADM is accessible by logging in to iDRAC using SSH or Telnet. Similar to Remote RACADM, at the RACADM prompt, directly run the commands without the RACADM prefix. Remote — Supports running RACADM commands from a remote management station such as a laptop or desktop. To run Remote RACADM commands, install the DRAC Tools utility from the OpenManage software on the remote computer.
PAGE 35
• To display the supported indexes for a specified group, run: racadm get device. Example racadm get nic.nicconfig NIC.nicconfig.1 [Key=NIC.Integrated.1-1-1#nicconfig] NIC.nicconfig.2 [Key=NIC.Integrated.1-2-1#nicconfig] NIC.nicconfig.3 [Key=NIC.Integrated.1-3-1#nicconfig] NIC.nicconfig.4 [Key=NIC.Integrated.1-4-1#nicconfig] • To display the object list for the specified group, run: racadm get device.. Example racadm get nic.nicconfig.2 [Key=NIC.Integrated.
PAGE 36
Option Description --nocertwarn Does not display certificate related warning message. -i Specifies the index number for the indexed group, if applicable. -g Specifies the group name if applicable. -o Specifies the object name if applicable. Using autocomplete feature Use the autocomplete feature to: • • • Display all the available RACADM commands in the alphabetical order on pressing the Tab key at the prompt.
PAGE 37
• Example 3: racadm> getl racadm> getled or LEDState: Not-Blinking • Example 4: racadm>> get bios.uefiBootSettings BIOS.UefiBootSettings BIOS.UefiBootSettings.UefiBootSeq BIOS.UefiBootSettings.UefiPxeIpVersion NOTE: In the RACADM autocomplete mode, some of the RACADM commands specific to certain server platforms may not be available. In such scenarios, execute the RACADM command in the normal execution mode.
PAGE 38
Supported RACADM Subcommands The following table provides the list of RACADM subcommands and their corresponding interface support. For more information about the RACADM subcommands including syntax and valid entries, see RACADM Subcommand Details. Table 2.
PAGE 39
Subcommand iDRAC on Blade Servers Telnet/SSH/Serial Local RACADM Remote RACADM license Yes Yes Yes nicstatistics Yes Yes Yes ping Yes Yes Yes ping6 Yes Yes Yes racdump Yes No Yes racreset Yes Yes Yes racresetcfg Yes Yes Yes remoteimage Yes Yes Yes rollback Yes Yes Yes sensorsettings Yes Yes Yes serveraction Yes Yes Yes set Yes Yes Yes setled Yes Yes Yes setniccfg Yes Yes Yes sshpkauth Yes Yes Yes sslcertupload No Yes Yes sslcertview Yes Ye
PAGE 40
Other Documents You May Need In addition to this guide, you can access the following guides available on the Dell Support website at www.dell.com/esmmanuals. To access the documents, click the appropriate product link. • • • • • • The Integrated Dell Remote Access Controller 8 (iDRAC8) User’s Guide provides information about configuring and using an iDRAC to remotely manage and monitor your system and its shared resources through a network.
PAGE 41
Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1. Go to Dell.com/support. 2. Select your support category. 3.
PAGE 42
2 RACADM Subcommand Details This section provides detailed description of the RACADM subcommands including the syntax and valid entries. Topics: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 42 Guidelines to Quote Strings Containing Special Characters When Using RACADM Commands Help and help subcommand arp autoupdatescheduler cd cd..
PAGE 43
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • racreset racresetcfg remoteimage rollback sensorsettings serveraction set setled setniccfg sshpkauth sslcertdownload sslcertupload sslcertview sslcertdelete sslcsrgen sslkeyupload sslresetcfg storage swinventory systemconfig systemerase systemperfstatistics techsupreport testemail testtrap testalert traceroute traceroute6 update usercertupload usercertview vflashsd vflashpartition vmdisconnect Guidelines to Quote Strings Containing Specia
PAGE 44
NOTE: The - (dash) character cannot be the first character of the string, regardless of whether the string is quoted. There are different escaping rules for double quotation marks. There are different escaping rules for using single quotation mark and double quotation marks. For using double quotation marks: The following characters must be escaped by prepending a backward slash: • • • • • $ (dollar sign) " (double quotation mark) ' (single quotation marks) ` (back quotation mark) \ (backward slash) For e
PAGE 45
To use this subcommand, you must have Debug privilege. To use this subcommand, you must have Execute Diagnostic Commands. Synopsis Input Example racadm arp N/A racadm arp Table 5. Output Address HW Type HW Address Mask Device 192.168.1.1 Ether 00:0d:65:f3:7c:bf C eth0 autoupdatescheduler Table 6. Details of autoupdatescheduler Description You can automatically update the firmware of the devices on the server. To run this subcommand, you must have the Server Control privilege.
PAGE 46
• -f — Specifies the catalog location and the filename. If the filename is not specified, then the default file that is used is catalog.xml. NOTE: If the file is in a subfolder within the share location, then enter the network share location in the –l option and enter the subfolder location and the filename in the –f option. • • • • • • • -ph — Specifies the FTP/HTTP proxy hostname. -pu — Specifies the FTP/HTTP proxy user name. -pp — Specifies the FTP/HTTP proxy password.
PAGE 47
• For HTTPS, run the command: racadm autoupdatescheduler create -u httpuser -p httppwd -l https:// test.com -f cat.xml -ph 10.20.30.40 -pu padmin -pp ppwd -po 8080 -pt http -time 14:30 -dom 1 -rp 5 -a 1 • For TFTP, run the command: racadm autoupdatescheduler create -l tftp://1.2.3.4 -f cat.xml.gz time 14:30 -dom 1 -rp 5 -a 1 • To view AutoUpdateScheduler parameter: racadm autoupdatescheduler view hostname = 192.168.0 sharename = nfs sharetype = nfs catalogname = Catlog.
PAGE 48
Input racadm> cd.. Output To traverse back to the previous directory, use the command. Example • Example 1: To traverse back from power to system object: • • Input: racadm/power> cd.. Output: system>> • Example 2: To traverse back from system object to the prompt: Input: racadm/system> cd.. Output: • • racadm>> clearasrscreen Table 9. Details of clearasrscreen Description Clears the last crash (ASR) screen that is in memory.
PAGE 49
Output A message is displayed indicating that the pending state is cleared or deleted. Example racadm clearpending NIC.Integrated.1-1 closessn Table 11. Details of closessn attribute Description Closes a communication session on the device. Use getssninfo to view a list of sessions that can be closed using this command. To run this subcommand, you must have the Administrator permission. NOTE: This subcommand ends all the sessions other than the current session.
PAGE 50
Example • racadm clrsel The SEL was cleared successfully • racadm clrsel -m server-1 Clear SEL log on server 1 config Table 13. Details of config attribute Description Allows you to set iDRAC configuration parameters individually or to batch them as part of a configuration file and then modify iDRAC configuration properties. If the data is different, the iDRAC object is written with a new value. NOTE: This subcommand will be deprecated in the later versions.
PAGE 51
• • Output Examples -i — The -i , or index option, is valid only for indexed groups and can be used to specify a unique group (used with -g and -o). The is a decimal integer from 1 through n, where n can vary from 1 to maximum number of indexes a particular group supports. If -i is not specified, a value of 1 is assumed for groups, which are tables that have multiple entries. The index is specified by the index value, not a named value. 'nx' is allowed for servers.
PAGE 52
coredumpdelete Table 15. Details of coredumpdelete Description Deletes any currently available coredump data stored in the RAC. To use this subcommand, you must have Execute Debug Command permission. To use this subcommand, you must have Clear Logs or Execute DebugCommands permission. NOTE: If a coredumpdelete command is issued and a coredump is not currently stored in the RAC, the command displays a success message. This behavior is expected.
PAGE 53
• • -s — Specifies the start time for the scheduled job in yyyymmddhhmmss format. The default value TIME_NOW starts the job immediately. -e — Specifies the expiry time for the scheduled job in yyyymmddhhmmss format. The default value TIME_NA does not apply the waiting time. NOTE: For the diagnostic report run operation, the time difference between the -s and -e options must be more than five minutes. Output Provides the Job ID for the diagnostic operation.
PAGE 54
• • • Critical Warning Info Valid examples of alert queries are: Input • • • • • idrac.alert.all idrac.alert.audit idrac.alert.audit.lic idrac.alert.audit.warning idrac.alert.audit.lic.critical • • • • • get — Displays the list of eventfilter settings. set — Configures the actions and notifications for a given eventfilter configuration. -i — Message ID for which the simulation is needed. -c — Alert category of the specific event filter. -a — The action that must be invoked when the event occurs.
PAGE 55
• Configure using subcategory and severity as parameters. For example, all information events under the licensing subcategory in the audit category are assigned power off as action and all notifications are disabled: racadm eventfilters set -c idrac.alert.audit.lic.info -a poweroff -n none • Configure the event generation interval for temperature statistics: racadm eventfilters set -c idrac.alert.system.tmps.
PAGE 56
• • • • Check the firmware update process status. Update iDRAC firmware from FTP or TFTP server by providing an IP address and optional path. Update iDRAC firmware from the local file system using Local and Remote RACADM. Roll back to the standby firmware. Allows you to update the firmware on the KVM, active CMC, standby CMC, iDRAC or an IOM infrastructure device. You can: • • • • Check the firmware update process status. Update CMC from FTP or TFTP server by providing an IP address and optional path.
PAGE 57
For SSH or Telnet or Serial: racadm fwupdate -g -u -a -d [-m ] racadm fwupdate -f -d [-m ] racadm fwupdate -u -m iominf- racadm fwupdate -s [-m ] racadm fwupdate -c [-m ] For Remote RACADM: racadm fwupdate -p -u -d [-m ] racadm fwupdate -g -u -a 192.168.0.10 -d firmimg.cmc -m cmc-active racadm fwupdate -r [-m ] racadm -r 192.168.0.
PAGE 58
• • -g — Downloads the firmware update using the TFTP server. -a — The IP Address option specifies the TFTP server IP address, used with -g option. Specifies the TFTP server IP address or FQDN used for the firmware image (used with -g). • -p — The -p, or put, option is used to update the firmware file from the managed system to iDRAC. The -u option must be used with the -p option.
PAGE 59
• Upload the firmware image from the FTP server and start the firmware update. • racadm fwupdate -f 192.168.0.100 fred xxx -d firmimg.cmc -m cmc-active Upload a firmware image from the client and start firmware update. • racadm fwupdate -p -u -d firmimg.cmc Start IOM infrastructure firmware update. • racadm fwupdate -u -m iominf-1 Update firmware on both the CMCs. • racadm fwupdate -g -u -a 192.168.0.2 -d firmimg.cmc -m cmc-active -m cmcstandby Update firmware on multiple servers.
PAGE 60
NOTE: These commands specifically apply to an active-CMC update. Signed CMC Firmware Image: • To get the firmware update status: racadm fwupdate –s –m cmc-active Invalid firmware: The uploaded firmware image does not contain a verification signature. Table 21.
PAGE 61
NOTE: INI file format is deprecated. It is recommended to use XML or JSON formats. • Server Configuration Profile XML/JSON format — XML/JSON format files can be exported to a local file, to an NFS network share or to a CIFS network share. NOTE: To run theGet sub-command for Server Configuration Profile XML files, use the Lifecycle Controller version 1.1 or later. NOTE: Some objects may have a pending value if a Set operation is performed on the object through a reboot job.
PAGE 62
• • -l—Specifies network share location to which the file will be exported. -t—Specifies the file type to be exported. The valid values are: • • • • • • • JSON—It exports the SCP JSON file to a network share file. xml—It exports the SCP xml format file, either to a local or network share file. ini—It exports the legacy configuration file. If -t is not specified, then the ini format file is exported. It can only be exported to a local file.
PAGE 63
• Export the xml configuration of the iDRAC component to a CIFS share. racadm get -f file -t xml -u myuser -p xxx -l //192.168.0/share iDRAC.Embedded.1 • -c Include password hash in the configuration .xml file. racadm get -f -t xml -l -u p -t xml --includeph getconfig Table 24. Details of getconfig attribute Description Retrieves iDRAC configuration parameters individually or all iDRAC configuration groups may be retrieved and saved to a file.
PAGE 64
• • • Output -o — The -o or object option specifies the object name that is used in the query. This option is optional and can be used with the -g option. -u — The-u or user name option, is used to display the configuration for the specified user. The option is the login name for the user. -v — The -v option displays more information with the display of the properties and is used with the -g option.
PAGE 65
• Displays the user group instance at index 2 with verbose information for the property values. racadm getconfig -g cfgUserAdmin -i 2 -v • Displays an entire group of serial configuration. racadm getconfig -g cfgSerial • Displays a single object from a particular group. racadm getconfig -g cfgSerial -o cfgSerialBaudRate • Displays an indexed group. racadm getconfig -g cfgUserAdmin -o cfgUserAdminUserName -i 2 • Displays the current Enhanced Cooling Mode property configuration.
PAGE 66
DHCP DHCPServerV4 MAC Address FQDD IPv4 Address Subnet Mask IPv6 Address Prefix Length IPv4 Gateway Address IPv4 DNSServer Address IPv4 DNSServer Address : : : : : : : : : 0: 1: Enabled 10.94.224.25 14-FE-B5-FF-B1-9C NIC.Integrated.1-1-1 10.94.225.189 255.255.255.128 fe80::7c5f:a114:84d4:17f6 64 10.94.225.129 10.116.2.250 10.116.2.251 getled Table 27. Details of getled attribute Description Displays the LED settings on a module: blinking, not blinking, or unknown (for empty slots).
PAGE 67
getniccfg Table 28. Details of getniccfg attribute Description Displays the current and static NIC settings for iDRAC. Displays the current NIC settings. Synopsis Input racadm getniccfg [-m ] –m must be one of the following values: • • • • Output chassis : Default state if -m is not specified. server- : where n=1–16 server- : where n=1–8; x = a, b, c, d (lower case) switch- : where n=1–6 NOTE: Table 29.
PAGE 68
IP Address 14 =:: IP Address 15 =:: LOM Status: NIC Selection =dedicated Link Detected =Yes Speed =1Gb/s Duplex Mode =Full Duplex Active NIC =Dedicated Static IPv4 settings: Static IP Address =192.168.0.120 Static Subnet Mask =255.255.255.0 Static Gateway =192.168.0.1 Static IPv6 settings: Static IP Address 1 =2000:de11:bcd1:fc14:1234:5678:2468:abcd/64 Static Prefix Length =64 Static Gateway =:: IPv6 information is displayed only if IPv6 is enabled in iDRAC.
PAGE 69
NOTE: On Local RACADM, the number of logs are restricted to 100 by default. • • --more — Displays one screen at a time and prompts you to continue (similar to the UNIX more command). -s — Specifies the starting record used for the display. • -c — Specifies the number of records to display. NOTE: On Remote RACADM, the number of logs are restricted to 25 by default. • • • -i — Displays the number of entries in the CMC log.
PAGE 70
Category AgentID Severity Timestamp Message Arg Message Arg Message Example = = = = 1 = 2 = = Audit CMC Information 2014-10-18 15:48:10 14503 48186 Successfully closed Session process: pid=14503 sid=4818 Display the recent 2 records for RAC log racadm getraclog -c 2 SeqNumber = 4102 Message ID = LIC201 Category = Audit AgentID = DE Severity = Warning Timestamp = 2014-06-12 01:38:19 Message = License yPMRJGuEf7z5HG8LO7gh assigned to device iDRAC expires in 4 days.
PAGE 71
getremoteservicesstatus Table 32. Details of getremoteservicesstatus Description Displays the status of a system.
PAGE 72
Example • Display entire log. racadm getsel • Display number of records in log. racadm getsel -i getsensorinfo Table 34. Details of getsensorinfo Description Displays the status for system sensors. NOTE: For Dell PowerEdge FX2 chassis with FM120x4 server, the power related information is not displayed. NOTE: General purpose graphical processing unit (GPGPU) status is displayed only on PowerEdge C4130 servers.
PAGE 73
System Board Fan3 RPM Ok 5880 RPM 600 RPM NA 0% System Board Fan4 RPM Ok 5880 RPM 600 RPM NA 0% System Board Fan5 RPM Ok 5640 RPM 600 RPM NA 144% System Board Fan6 RPM Ok 5880 RPM 600 RPM NA 152% Table 39. Voltage sensor CPU1 VCORE PG Ok Good NA NA System Board 3.3V PG Ok Good NA NA System Board 5V AUX PG Ok Good NA NA CPU1 M23 VPP PG Ok Good NA NA System Board 1.
PAGE 74
System Board Pwr Consumption Ok 56 Watts NA 1386 Watts 0 Watts [N] Table 41. PROCESSOR sensor CPU1 Status Ok Presence Detected NA NA CPU2 Status N/A Absent NA NA Table 42.
PAGE 75
4 4 4 4 4 4 23:09:40 23:09:40 23:09:40 23:09:40 23:09:40 23:09:40 idrac8 idrac8 idrac8 idrac8 idrac8 idrac8 L4, L4, L4, L4, L4, L4, S3 S3 S3 S3 S3 S3 [10297]: [10297]: [10297]: [10297]: [10297]: [10297]: ret is 0 probename is Chassis Controller pCMCStatusobj->offsetKey is 24 pCMCStatusobj->sensorValue is 0 MAP Uninitialized, time to uninit = 0 millisec RACADM total execution time: 1680 milliseconds Table 44.
PAGE 76
NOTE: Based on the Session ID (SSNID) or the user name (User), the iDRACCMC administrator can close the respective sessions or all the sessions using the closessn subcommand. For more information, see closessn. Synopsis racadm getssninfo [-u ] [-A] racadm getssninfo [-u | -u *] [-A] Input • • -u — displays only sessions associated with a specific user. -A — does not display headers or labels. Table 50. Example SSNID Type User IP Address Login Date/Time 58999 SSH root 192.
PAGE 77
NOTE: The host name and OS Name fields in the getsysinfo output display accurate information only if the Dell OpenManage Server Administrator is installed on the managed system. Else, these fields may be blank or inaccurate. An exception to this are VMware operating system names, which are displayed even if the Server Administrator is not installed on the managed system.
PAGE 78
Chassis Midplane Version= 1.1 Power Status = ON Output RAC Information: RAC Date/Time = Thu Sep Firmware Version Firmware Build Last Firmware Update Hardware Version MAC Address = = = = = 2.20.20.20 41 09/02/2015 22:18:35 0.01 B8:2A:72:FC:4F:B0 Common settings: Register DNS RAC Name DNS RAC Name Current DNS Domain Domain Name from DHCP = = = = 1 ipmierrata sha512.
PAGE 79
• Display iDRACCMC information racadm getsysinfo -d • Display IPv4 details without header racadm getsysinfo -A "RAC IPv4 Information:" "1" "10.94.195.33" "10.94.195.1" "255.255.255.0" "1" "10.94.192.67" "0.0.0.0" "1" "CMC IPv4 Information:" "1" "192.168.0.10" "192.168.0.10" "255.255.255.0" "1" "192.168.0.10" "0.0.0.0" "1" gettracelog Table 53. Details of attribute Description Lists all the trace login entries of iDRAC. Displays the CMC diagnostic trace log.
PAGE 80
getversion Table 54. Details of getversion attribute Description Displays the current software version, model and generation information, and whether the target device can be updated. NOTE: The Linux shell script does not support the characters—$ (dollar),` (back quote), \ (forward slash), & (ampersand), ( (open bracket), ) (Close bracket), = (equal), | (Pipe), ; (semi colon)," (Double quote), ' (single quote), < (less than), and > (greater than).
PAGE 81
server-7 1.0.6 PowerEdgeM620 server-9 1.0.5 PowerEdgeM520 racadm getversion Bios Version = 2.0.18 iDRAC Version = 2.00.00.00 Lifecycle Controller Version = 2.00.00.00 Table 57. Details server-1 1.6.0 PowerEdgeM520 server-2 6.3.0 PowerEdgeM610x server-4 7.0.0 PowerEdgeM710HD server-5 6.3.0 PowerEdgeM710 server-7 1.7.1 PowerEdgeM620 server-9 1.7.1 PowerEdgeM520 Table 58.
PAGE 82
hwinventory Table 59. Details of hwinventory Description Allows you to display or export current internal hardware inventory or shipped hardware inventory by device. NOTE: iDRAC supports a maximum of 12 parallel sessions of hardware inventory. Synopsis • • • • racadm racadm racadm racadm or NFS Input • — Specifies the FQDD of the target device. • • • • hwinventory hwinventory NIC|FC hwinventory hwinventory export -f -u -p -l • FQDD — NIC.
PAGE 83
PCI Sub Vendor ID: PCI Device ID: PCI Sub Device ID: Current MAC Address: Permanent MAC Address: Virtual iSCSI MAC Address: Permanent iSCSI MAC Address: Virtual FIP MAC Address: Permanent FIP MAC Address: Permanent FCoE MAC Address: Slot Type: Data Bus Width: Slot Length: Bus Number: DeviceNumber: Function Number: Last Update Time: Last System Inventory Time: ProductName: WWN: VirtWWN: WWPN: VirtWWPN: Family Version: Controller BIOS Version: EFI Version: Max Bandwidth: Min Bandwidth: FCoE WWNN: Vendor Name:
PAGE 84
Priority Flow Control: DCB Exchange Protocol: Congestion Notification: VEB-VEPA Single Channel: VEB-VEPA Multi Channel: EVB: BPE: Open Flow: Partition WOL Support: Virtual Link Control Partition RX Flow Control: Partition TX Flow Control: TX Bandwidth Control Maximum: TX Bandwidth Control Minimum: • Not Not Not Not Not Not Not Not Not Not Not Not Not Not Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable Capable To export the inventory to a remote CIFS
PAGE 85
PCI Sub Device ID: PCI Bus: PCI Device: PCI Function: Vendor Name: Device Name: 2001000E1E091075 WWN: VirtWWN: WWPN: VirtWWPN: Chip Type: Family Version: EFI Version: OS Driver Version: First FC Target WWPN: First FC Target LUN: Second FC Target WWPN: Second FC Target LUN: Hard Zone Address: Hard Zone Enable: FC Tape Enable: Loop reset Delay: Frame Payload Size : Fabric Login Retry Count: Fabric Login Timeout: Port Login Retry Count: Port Login Timeout: Port Down Retry Count: Port Down Timeout: Link Down Ti
PAGE 86
collisions:0 txqueuelen:1000 RX bytes:272532097 (259.9 MiB) TX bytes:0 (0.0 B) inlettemphistory Table 62. Details of inlettemphistory Description Displays the average and the peak temperatures during the last hour, day, week, month, or year. Also Exports the inlet temperature history data file. The file can be exported to a remote file share, local file system, or the management station. NOTE: For FM120x4 systems, this subcommand provides the historical data for system board temperature.
PAGE 87
Peak Last Last Last Last Last Temperatures Hour = 23C ( Day = 25C ( Week = 27C ( Month = 29C ( Year = 29C ( 73.4F 77.0F 80.6F 84.2F 84.2F ) ) ) ) ) [At [At [At [At [At Wed, Tue, Fri, Wed, Wed, 30 29 25 16 16 May May May May May 2012 2012 2012 2012 2012 11:00:57] 15:37:23] 10:38:20] 15:34:13] 15:34:13] jobqueue Table 63. Details of jobqueue Description Enables you to view and delete a job or jobs in the current Job Queue. NOTE: • To run this subcommand, you must have the Server control privilege.
PAGE 88
Example • View jobs in the current job queue. racadm jobqueue view • View status of a specific job ID. racadm jobqueue view -i • Issue configuration changes for a PERC controller then start a real time job to execute the changes. racadm set RAID.Slot.3-1.RAIDdefaultWritePolicy WriteBack racadm set RAID.Slot.3-1.Name “Prod Workload” racadm jobqueue create RAID.Slot.3-1 –realtime • Delete all possible jobs from the current job queue.
PAGE 89
lclog Table 65. Details of lclog Description Allows you to: • • • • • Export the lifecycle log history. The log exports to remote or local share location. View the lifecycle log for a particular device or category. Add comment to a record in lifecycle log. Add a work note (an entry) in the lifecycle log. View the status of a configuration job. NOTE: • • Synopsis When you run this command on Local RACADM, the data is available to RACADM as a USB partition and may display a pop-up message.
PAGE 90
• • • • • • • • • • • • • • Storage • Worknotes • Config • Updates • Audit -b —The subcategory used to filter the records. Provides multiple subcategories using a "," as the delimiter. -q—The sequence number from which the records must be displayed. Records older than this sequence number is displayed. NOTE: This parameter input is an integer. If an alphanumeric input is provided, then invalid subcommand syntax error is displayed. -n—Specifies the n number of records that must be displayed.
PAGE 91
• Display the records under storage and system categories with severities set to warning or critical. racadm lclog view -c storage,system -s warning,critical • Display the records having severities set to warning or critical, starting from sequence number 4. racadm lclog view -s warning,critical -q 4 • Display 5 records starting from sequence number 20. racadm lclog view -q 20 -n 5 • Display all records of events that have occurred between 2011-01-02 23:33:40 and 2011-01-03 00:32:15.
PAGE 92
Synopsis Input • racadm license view [-c ] • racadm license import [-f ] -l -u -p -c [-o] • racadm license export -f [-l ] [-u ] [-p ] -e -c • racadm license delete -t [-o] • racadm license delete -e [-o] • racadm license delete -c [-o] • racadm license replace -u -p -f l
PAGE 93
• Import a license from a CIFS share to a device, in this case Embedded iDRAC. racadm license import -u admin -p xxx -f License.xml -l //192.168.0/licshare -c idrac.embedded.1 • Import a license from an NFS share to a device, in this case Embedded iDRAC. racadm license import -f Licen.xml -l 192.168.0:/share -c idrac.embedded.1 • Import a license by overriding the EULA warning. racadm license import -u admin -p passwd -f License.xml -l //192.168.0/licshare -c idrac.embedded.
PAGE 94
netstat Table 67. Details of netstat Description Display the routing table and network statistics. Synopsis racadm netstat Examples • To display the routing table and network statistics, type the following command: $ racadm netstat nicstatistics Table 68. Details of nicstatistics Description Synopsis Displays the statistics for the NIC FQDD. • racadm nicstatistics • racadm nicstatistics • racadm hwinventory NIC.Integrated.
PAGE 95
Total Unicast Bytes Transmitted: • 0 To get the network statistics, type the following command: $ racadm nicstatistics NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:10 NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:11 NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:12 NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:13 NIC.Slot.5-2-1 : QLogic CNA Gigabit Ethernet-B8:AC:6F:B3:BF:14 ping Table 69.
PAGE 96
Example Pinging 2011:de11:bdc:194::31 from 2011:de11:bdc:194::101 with 32 bytes of data: Reply from 2011:de11:bdc:194::31: time<1ms Reply from 2011:de11:bdc:194::31: time<1ms Reply from 2011:de11:bdc:194::31: time<1ms Reply from 2011:de11:bdc:194::31: time<1ms Ping statistics for 2011:de11:bdc:194::31: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms RACADM Proxy Table 71.
PAGE 97
User Configuration Administrator Configure User Clear Logs Administrator Logs • • • Chassis Control Administrator System Control Server Administrator System Control Test Alert User System Operations Debug Command Administrator Debug Fabric x Administrator (where x is A, B, or C) System Control The user privilege in the Remote RACADM proxy for CMC maps to iDRAC privilege. When CMC is not placed on the network, the import, export, and file operation commands to CIFS, NFS, or FTP will fail.
PAGE 98
To run this subcommand, you must have the Administrator privilege. To run this subcommand, you must have the Debug permission.
PAGE 99
Current IP Address Current IP Gateway Current IP Netmask DHCP Enabled Current DNS Server 1 Current DNS Server 2 DNS Servers from DHCP = = = = = = = 192.168.0.1 192.168.0.1 192.168.0.1 0 0.0.0.0 0.0.0.
PAGE 100
ff00::/8 256 0 :: 0 eth1 Kernel IP routing table Destination Gateway 0.0.0.0 192.168.0.1 192.168.0.1 0.0.0.0 Genmask 0.0.0.0 192.168.0.1 Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address tcp 0 0 192.168.0.1:53986 tcp 0 0 192.168.0.1:53985 tcp 0 0 192.168.0.1:199 tcp 0 0 192.168.0.1:199 U Flags UG U MSS Window 0 0 0 0 Foreign Address 192.168.0.1:199 192.168.0.1:199 192.168.0.1:53986 192.168.0.
PAGE 101
Current DNS Server 2 DNS Servers from DHCP Register DNS CMC Name DNS CMC Name Current DNS Domain = = = = = 0.0.0.
PAGE 102
NOTE: After you run the racreset subcommand, CMC may require up to two minutes to return to a usable state. NOTE: There is a 100 percent fan request when the command is run against the servers. Synopsis racadm racreset soft racadm racreset hard racadm racreset soft -f racadm recreset hard -f racadm racreset [-m [-f]] Input • -f — This option is used to force the reset.
PAGE 103
NOTE: Certain firmware processes must be stopped and restarted to complete the reset to defaults. iDRAC becomes unresponsive for about 30 seconds while this operation completes. Synopsis • RAC reset operation initiated successfully. It may take several minutes for the RAC to come online again. racadm racresetcfg Input Example • racadm racresetcfg -f • racadm racresetcfg -all • • -f — Force resetcfg. If any vFlash partition creation or formatting is in progress, iDRAC returns a warning message.
PAGE 104
• NOTE: Use a forward slash (/) when providing the image location. If backward slash (\) is used, override the backward slash for the command to run successfully. For example: racadm remoteimage -c -u user -p xxx -l /\/\192.168.0.2/\CommonShare/ \diskette NOTE: The following options only apply to connect and deploy actions • -u —Username User name to access the network share. For domain users, you can use the following formats: Example • • • • -p domain/user domain\user user@domain —Password to access
PAGE 105
Synopsis racadm rollback [--reboot] NOTE: To get the list of available rollback versions and FQDDs, run the racadm swinventory command. Input • • : Specify the FQDD of the device for which the rollback is required. --reboot: Performs a graceful system reboot after the BIOS firmware rollback. Example • To perform BIOS firmware rollback: racadm rollback iDRAC.Embedded.1-1 RAC1056: Rollback operation initiated successfully.
PAGE 106
• Input racadm serveraction -m • -m — Must be one of the following values: • • server–: where n=1–16 • server–: where n=1–8; x=a–d (enter lowercase letter only). -a — Performs power action on all servers. Not allowed with the powerstatus action. — Specifies the power management operation to perform. The options are: • • hardreset — Performs a force reset (reboot) operation on the managed system.
PAGE 107
• Get Power Status of blade 16 on CMC by using the following command: racadm serveraction -m server-16 powerstatus ON • Turn off the server 16 from CMC, when the power is already turned off on that server by using the following command: racadm serveraction -m server-16 powerdown Server is already powered OFF. • Power action on all servers by using the following command: racadm serveraction -a powerup set Table 80. Details of set Description Modifies the value of configuration objects on a component.
PAGE 108
• racadm get ..