Getting Started With Your PowerVault™ 124T Začínáme se systémem PowerVault™ 124T Démarrage de votre PowerVault™ 124T Zum Einstieg mit Ihrem PowerVault™ 124T Πρώτη Χρήση του PowerVault™ 124T Wprowadzenie do PowerVault™ 124T Cómo empezar a utilizar su PowerVault™ 124T PowerVault™ 124T תחילת עבודה עם Primeiros passos com o PowerVault™ 124T PowerVault™ 124T 入門 www.dell.com | support.dell.
Information in this document is subject to change without notice. © 2006 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Linux is a registered trademark of Linus Torvalds. NetWare is a registered trademark of Novell, Inc.
CAUTION: Before performing the following procedure, read and follow the safety instructions and important regulatory information in your PowerVault 124T Product Information Guide located in the box containing the PowerVault 124T. POZOR! Než provedete následující úkony, přečtěte si a řiďte se bezpečnostními pokyny a důležitými regulačními informacemi v Informační příručce produktu PowerVault 124T, umístěné v krabici se systémem PowerVault 124T.
Unpack your system and accessories. Vybalte systém a příslušenství. Save all shipping materials in case you need them later. (Your system may not include all of the accessories shown.) Uschovejte veškerý balicí materiál pro případ, že jej budete později potřebovat. (Váš systém nemusí obsahovat veškeré zobrazené příslušenství.) 1. SCSI cable 2. SCSI terminator 3. Power cable 4. Quick Start Guide 5. CD (drivers and documentation) 6. Magazine blank 7. Bar code labels 8. TORX L-key drivers (T8, T10) 9.
Install the PowerVault 124T in a rack. Instalujte systém PowerVault 124T do stojanu. See your rack installation documentation for instructions on installing your PowerVault 124T in a rack. For more information, visit PowerEdge Racks. V dokumentaci k instalaci stojanu naleznete pokyny k instalaci systému PowerVault 124T do stojanu. Více informací naleznete zde: Stojany PowerEdge. Installez le PowerVault 124T dans un rack. Installieren Sie PowerVault 124T in einem Rack.
Establish the SCSI and network connections. Zapojte SCSI a síù. Connect the SCSI cable (2) and terminator (3) if the unit is at the end of the SCSI bus. Connect an Ethernet cable (1). Zapojte kabel SCSI (2) a zakončovací prvek (3), je-li jednotka na konci sběrnice SCSI. Zapojte kabel Ethernet (1). Effectuez les connections SCSI et réseau. Erstellen Sie die SCSI- und Netzwerkverbindungen. Connectez le câble SCSI (2) et le terminateur (3) si l'unité est à l'extrémité du bus SCSI.
Connect the system to power. Připojte systém ke zdroji napětí. NOTE: Be certain that the host server is powered off before connecting POZNÁMKA: Před připojením automatického zavaděče se the autoloader. ujistěte, že hostitelský server je vypnut. Connect the system's power cable(s) to the system. Next, plug the other end of the cable into a grounded electrical outlet or a separate power source such as an uninterruptible power supply (UPS) or a power distribution unit (PDU).
Verify robot/drive seen by operating system. Ověřte robot/jednotku viděnou operačním systémem. Microsoft® Windows®: Under Device Manager, an unknown media changer should be present. Under Tape Drive, you should see the drive that is configured for your autoloader. Microsoft® Windows®: pod Správce zařízení by měl být zahrnut neznámý měnič médií. Pod Pásková jednotka byste měli uvidět jednotku, konfigurovanou pro Váš automatický zavaděč.
Configure the PowerVault 124T. Konfigurace systému PowerVault 124T. The default IP address is 192.168.20.128. Výchozí adresa IP je 192.168.20.128. The default password for the front panel is 000000 for Administrator, and 111111 for Operator. Výchozí heslo pro přední panel je 000000 pro Správce a 111111 pro Operátora. The default Username for the On-board Remote Management Utility is admin and the password is password.
ק Configure el PowerVault 124T. La dirección IP predeterminada es 192.168.20.128. Para el Administrador, la contraseña predeterminada para el panel frontal es 000000 y para el Operador es 111111. El nombre de usuario predeterminado de la Utilidad de administración remota de tarjeta incorporada es admin y la contraseña es password. .192.168.20.128 היאIP ברירת המחדל של כתובת , עבור המנהל000000 ברירת המחדל של הסיסמה ללוח הקדמי היא .