Setup Guide

Table 6. Connection Settings: wnos.ini files only (continued)
Parameter Description
[SupportBigMonitor={yes, no}] EnsureDpIsOn—When this option is enabled, the thin client resumes only
after you connect the monitor to the DisplayPort.
SupportBigMonitor—This option is applicable only for the Wyse 3040 Thin
Client. When you enable this parameter, the Wyse 3040 Thin Client supports
up to 3440 x 1440 display resolution.
DelCertificate={filename, all, builtin}
filename—Removes the file from the nand flash or from the memory.
all—Removes all certificates except built-in certificates included by default.
builtin—Removes all certificates including the public certificates included by
default.
From ThinOS 8.6_019 release, the specific file name supports wildcard
variables, such as $TN.pfx, $TN, and WT*.pfx.
DesktopColorDepth={16, 32}
[RGB565={no, yes}]
DesktopColorDepth — Sets the desktop color to 16 or 32 bits. If
DesktopColorDepth=16, the default color is 15 bits.
RGB565 — Default is no. Applies only if the desktop color is using 16 bits.
NOTE:
If the RBG565 parameter value is changed to yes, the thin client will
require a reboot.
DHCPExpire={reboot, shutdown}
Default is reboot.
When a DHCP lease expires, a message notifies the user as follows: DHCP
Expired, you must reboot.
reboot — After 5 seconds, the system reboots.
shutdown — After 5 seconds, the system shuts down.
DHCPOptionsRemap={no, yes}
[DisableOption12={no, yes}]
[FileServer={128 to 254}]
[RootPath={128 to 254}]
[FtpUserName={128 to 254}]
[FtpPassWord={128 to 254}]
[PnliteServer={128 to 254}]
[DomainList={128 to 254}]
[VDIBroker-{248 to 254}]
[Discover={
yes, no}]
[WMSGroupKey={128-254}]
[WMSServer={128-254}]
[WMSMQTTServer={128-254}]
WMSCAValidation={128-254}]
Default is no.
DHCPOptionsRemap — Specifies whether or not the following options can
be set.
The value for each option must be from 128 to 254. Values for the options
must be different for each option. These options are used to configure DHCP
server tags for thin client booting.
The option DisableOption12 sets if the option tag 12 in DHCP is accepted or
not. As default, DHCP option 12 sets the hostname and domain name of the
terminal. For example, the information of option 12 is terminal
name.wyse.com, the terminal name will be set as terminalname and the
domain name will be set as wyse.com.
If you set different value for DisableOption12 from the value in NVRAM, the
system will automatically reboot to make the value valid. (CIR36891)
Discover—If Discover=yes, the device fetches Wyse DHCP options from
DHCP server, otherwise, it prevents the device from fetching those
information. Default value is yes. If the device receives FileServer information
through the DHCP server, then the associate User interface is protected.
NOTE: The WMSGroupKey, WMSServer, WMSMQTTServer and
WMSCAValidation options are specified to remap the tags forWMS
configuration.
DHCPUserClassID=class_id
[ParseVendorInfo={no, yes}]
DHCPUserClassID — Specifies the UserClassID used for DHCP.
ParseVendorInfo — Default is yes. Yes/no option to specify whether or not
ThinOS will interpret DHCP option 43.
Parameters for wnos INI files only 23