Installation Guide

ManualsBrandsDelta ManualsKitchen Faucets11946-SSSD-DST

SINGLE LEVER WIDESPREAD

KITCHEN FAUCETS

LLAVE DE AGUA, DE ALCANCE AMPLIO,

DE UNA PALANCA PARA COCINAS

ROBINETS À ENTRAXE LONG À UNE

POIGNÉE POUR ÉVIER DE CUISINE

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

• ToREAD ALLwarnings,care,andmaintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien;

Models/Modelos/Modéles

155-DST,1980-DST,

4380-SD-DST&11946-SD-DST

Series/Series/Seria

SILICONE

Icons

12/7/10   Rev.A

ASMEA112.18.1/CSAB125.1

Icons

64943

Summary of content (12 pages)

PAGE 1
SINGLE LEVER WIDESPREAD KITCHEN FAUCETS LLAVE DE AGUA, DE ALCANCE AMPLIO, DE UNA PALANCA PARA COCINAS ROBINETS À ENTRAXE LONG À UNE POIGNÉE POUR ÉVIER DE CUISINE 64943 ASME A112.18.1 / CSA B125.1 Models/Modelos/Modéles 155-DST, 1980-DST, 4380-SD-DST & 11946-SD-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Lifetime Faucet and Finish Limited Warranty All parts and finishes of the Delta® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for as long as the original consumer purchaser owns their home.
PAGE 3
1/8" 4 1 5 2 3 Maintenance If faucet exhibits very low flow: A. Remove aerator (1) with supplied wrench (2) and clean , or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (5) is tightened securely with a wrench.* If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (5) is tight. Cleaning and Care If faucet leaks from spout outlet–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3).
PAGE 4
1 A. B. 2 A. 2 2 3 1 3 1 4 3 4 2 1 1 5 1 6 2 Spout Installation If you are installing the faucet on a Stainless Steel or a thin sink use RP37490 Stablization Plate SUPPLIED WITH FAUCET. A. Shut off water supplies. Assemble base (1) and gasket (2). Place base and gasket over mounting hole for the spout. Slide spout tube and shank (3) through base and position spout assembly onto base (Note the “F” (4) is positioned toward the front).
PAGE 5
B. C. 3 6 5 1 1 4 1 1 3 2 3 2 B. Slide tube end (1) into adapter (2) and secure with clip (3). Pull moderately on tube to ensure connection has been made. B. Deslice el extreme del tubo (1) en el adaptador (2) y fije con el gancho (3). Hale el tubo moderadamente para asegurar que la conexión se ha hecho. B. Introduisez extrémité du tube (1) dans l’adaptateur (2) et fixez-le avec l’agrafe (3).
PAGE 6
3 B. A. B-2 B-1 3 3 1 1 2 2 4 1 3 4 B-3 1 1 For Models With A Side Spray A. Mount spray support assembly (1) in far right hole in sink. HAND TIGHTEN ONLY. Insert spray hose (2) down through spray support. B. Pull diverter clip (1) outward until loose; but, do not completely remove. Remove diverter cap (2) from diverter (3) and discard if installing a side spray. Keeping the diverter clip pulled out, insert spray hose nipple (4) into diverter.
PAGE 7
4 A. B. 2 1 OR 2 2 O 3 OU 3 4 1 1 2 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 8
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 9
5 6 2 1 6 3 2 3 4 2 1 4 5 For Models with Soap Dispenser Remove aerator (1) using supplied wrench (2) and move faucet handle (3) to the full on mixed position. Turn on hot and cold water supplies (4) and flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. Reinstall aerator. Note: For future use, aerator wrench (2) can be clipped to the supply line after flushing faucet. Remove nut (1) and separate head (2) from body (3).
PAGE 10
7 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 11
64943 Rev.
PAGE 12
64943 Rev.