Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceCollins Single-Handle Kitchen Faucet in Stainless

SINGLE HANDLE KITCHEN FAUCET

LLAVE DE COCINA DE PALANCA

ROBINET DE CUISINE À UNE MANETTE

Models/Modelos/Modèles

100-DST, 101-DST, 117-DST,

119-DST, 140-DST, 141-DST,

175-DST, 300-DST, 319-DST,

340-DST, 400-DST, 417-DST,

419-DST, 440-DST & 441-DST

Series/Series/Seria

Para instalación fácil de su llave

Delta usted necesitará:

•LEER TODAS las instrucciones

completamente antes de empezar.

•LEER TODOS los avisos, cuidados,

e información de mantenimiento.

For easy installation of your

Delta faucet you will need:

•ToREAD ALL the instructions completely

before beginning.

•  To  READ ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Icons

SILICONE

Icons

SILICONE

Icons

Pour installer votre robinet

Delta facilement, vous devez:

•LIRE TOUTES les instructions avant

de débuter;

•LIRE TOUS les avertissements ainsi que

toutes les instructions de nettoyage et

d’entretien;

5/21/11 Rev. C

ASME A112.18.1 / CSA B125.1

64283

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE KITCHEN FAUCET 64283 LLAVE DE COCINA DE PALANCA ROBINET DE CUISINE À UNE MANETTE UP C ® ASME A112.18.1 / CSA B125.1 Models/Modelos/Modèles 100-DST, 101-DST, 117-DST, 119-DST, 140-DST, 141-DST, 175-DST, 300-DST, 319-DST, 340-DST, 400-DST, 417-DST, 419-DST, 440-DST & 441-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Lifetime Faucet and Finish Limited Warranty the original consumer purchaser must be made available to Delta for all warranty claims. THIS IS THE EXCLUSIVE WARRANTY BY DELTA FAUCET COMPANY, WHICH DOES NOT MAKE ANY OTHER WARRANTY OF ANY KIND, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY.
PAGE 3
5 4 3 1 1 2 6 Maintenance If spray attachment does not function properly: Replace diverter and hose assembly (6). If faucet exhibits very low flow: A. Remove and clean aerator (1) (Some models require wrench (2) to remove aerator), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (4) is tightened securely with a wrench.* * WARNING: Failure to securely tighten bonnet nut with a wrench could result in water damage.
PAGE 4
1 300, 319 & 340 Series 100, 119 & 140 Series B. A. 1 1 3 3 3 3 1 2 2 100, 119 & 140 Series 300, 319 & 340 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Slide gasket (1) over tubes (2) and install onto bottom of faucet. NOTE: If surface is uneven, use silicone sealant under the gasket. Feed tubes down through center hole in sink. Secure faucet to sink with mounting nuts (3) supplied with your faucet. Continue to step 3. A. 100, 119 y 140 Series SHUT OFF WATER SUPPLIES. Remove old faucet.
PAGE 5
1 400, 419 & 440 Series B. A. 1 3 3 3 1 2 2 400, 419 & 440 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet. Slide gasket (1) over tubes (2) and install onto bottom of faucet. NOTE: If sink is uneven, use silicone sealant under the gasket. Feed tubes down through mounting hole in sink. Secure faucet to sink with mounting nuts (3) supplied with your faucet. B. Mount the spray support (1) in far right hole in sink. Hand tighten nut (2). Insert sprayer and hose (3) down through support assembly.
PAGE 6
1 175, 417 & 441 Series 101, 117 & 141 Series B. A. 1 1 3 2 2 1 2 3 3 4 4 2 2 101, 117 & 141 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Make sure base, spacer and gasket (1) are properly positioned under new faucet. Feed tubes and shank (2) down through hole in sink. Secure faucet to sink with bracket (3), using nut and wrench (4) supplied with your faucet. NOTE: If sink is uneven, use silicone sealant under the gasket. Continue to step 3.
PAGE 7
B. A. 2 3 3 1 1 3 2 2 2 1 For Sprayer Models Only A. Pull on clip (1) until disengaged. Pull down on diverter plug (2) to remove. Discard diverter plug. Caution: Do not remove tube clip (3). B. Keeping clip (1) disengaged, insert diverter hose end (2) into diverter housing (3) until seated. Push in clip (1) until it snaps. Pull down moderately to ensure connection has been made. Para el rociador modela solamente A. Hale el sujetador o gancho (1) hasta que se desencaje.
PAGE 8
3 A. B. 2 OR 2 1 O 2 OU 3 1 3 4 2 1 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 9
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 10
4 5 2 1 1 3 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 11
RP63792 Stiffening Kit (Reduce Flexibility For Commercial Applications) Juego Atiesador (Reduce la Flexibilidad en Aplicaciones Comerciales) Kit de renfort (réduit la flexibilité pour les applications commerciales) RP63264 Adapters (10) 3/8”-24 UNEF to 1/2”-20 UN Adaptado rs (10) 3/8”-24 UNEF a 1/2”-20 UN Adapteurs (10) 3/8 po-24 UNEF à 1/2 po-20 UN RP63265 Adapters (10) 3/8"-24 UNEF to 1/2"-14 NPSM Adaptadors (10) 3/8”-24 UNEF a 1/2”-14 NPSM Adapteurs (10) 3/8 po-24 UNEF à 1/2 po-14 NPSM RP63263 Ada
PAGE 12
RP53996 Tube Clip Presilla del tubo Agrafe de tube RP64288 Gasket Empaque Joint RP13938 O-Rings (2) Anillos O (2) Joints torique (2) RP54235▲ Spray & Hose Assembly Rociador Douchette RP50952 Plastic Sleeves Mangas Plásticas Manchons en plastique RP47030 Nut and Wrench Tuerca y Llave Ècrou et rondelle RP47029 Mounting Bracket Soporte de Montaje Support de montage RP54236▲ Escutcheon, Spacer & Gasket Chapetón, Separadore y Empaque Boîtier, Pièce D’espacement et Joint RP54232▲ Handle w/Button & Set