Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceClassic Single-Handle Side Sprayer Kitchen Faucet in Chrome

SINGLE HANDLE KITCHEN FAUCET

LLAVE DE COCINA DE PALANCA

ROBINET DE CUISINE À UNE MANETTE

Models/Modelos/Modèles

100-DST, 101-DST, 140-DST,

141-DST, 175-DST, 300-DST,

340-DST, 400-DST, 440-DST &

441-DST Series/Series/Seria

Para instalación fácil de su llave

Delta usted necesitará:

• LEER TODAS las instrucciones

completamente antes de empezar.

• LEER TODOS los avisos, cuidados,

e información de mantenimiento.

For easy installation of your

Delta faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Icons

SILICONE

Icons

Pour installer votre robinet

Delta facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi que

toutes les instructions de nettoyage et

d’entretien;

06/17/2019 Rev. D

75106

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE KITCHEN FAUCET 75106 LLAVE DE COCINA DE PALANCA ROBINET DE CUISINE À UNE MANETTE Models/Modelos/Modèles 100-DST, 101-DST, 140-DST, 141-DST, 175-DST, 300-DST, 340-DST, 400-DST, 440-DST & 441-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici. NE CO TEF LO N LI • To READ ALL the instructions completely before beginning. • To READ ALL warnings, care, and maintenance information.
PAGE 2
1 300 & 340 Series / Seria 100 & 140 Series / Seria B. A. 1 1 3 3 3 3 1 2 2 100 & 140 Series 300 & 340 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Slide gasket (1) over tubes (2) and install onto bottom of faucet. NOTE: If surface is uneven, use silicone sealant under the gasket. Feed tubes down through center hole in sink. Secure faucet to sink with mounting nuts (3) supplied with your faucet. Continue to step 3. A. 100 y 140 Series SHUT OFF WATER SUPPLIES. Remove old faucet.
PAGE 3
B. 400 & 440 Series / Seria A. 1 3 3 1 3 2 2 400 & 440 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet. Slide gasket (1) over tubes (2) and install onto bottom of faucet. NOTE: If sink is uneven, use silicone sealant under the gasket. Feed tubes down through mounting hole in sink. Secure faucet to sink with mounting nuts (3) supplied with your faucet. B. Note: If you prefer not to use side sprayer, skip this step and move to page 8. Mount the spray support (1) in far right hole in sink.
PAGE 4
101 & 141 Series / Seria 175 & 441 Series / Seria B. A. 1 1 3 2 2 1 2 3 3 4 4 2 2 101 & 141 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Make sure base, spacer and gasket (1) are properly positioned under new faucet. Feed tubes and shank (2) down through hole in sink. Secure faucet to sink with bracket (3), using nut and wrench (4) supplied with your faucet. NOTE: If sink is uneven, use silicone sealant under the gasket. Continue to step 3.
PAGE 5
2 A. 1 1 3 2 2 1 B. “SNAP” ‘CHASQUIDO’ «CLAQUEMENT» 1 1 5 1 5 1 4 4 4 For Sprayer Models Only A. Swing open lower clip (1). Pull down on diverter plug (2) to remove. Discard diverter plug. Caution: Do not remove upper clip (3). B. Keeping lower clip (1) disengaged, insert diverter hose end (4) into diverter housing (5) until seated. To secure diverter hose, rotate lower clip (1) until an audible snap is heard. Pull down moderately to ensure connection has been made.
PAGE 6
3 A. B. OR 2 O 1 3 Standard Connections B. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) to supply valve connection (4). Turn nut until it feels snug. Then tighten nut at least 2 more turns with a wrench. Repeat for other tube. Turn on water, examine for leaks. A.
PAGE 7
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 NOTICE Failure to use plastic sleeve (ferrule) in the correct orientation will result in disconnection and possible water damage. 1. Determine desired length of supply tube (1). Leave 1" or 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (ferrule) (3) onto cut supply tube.
PAGE 8
4 5 2 1 1 3 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 9
4 3 2 1 5 Maintenance Note: Do not attempt to disassemble cartridge (2). There are no repairable parts inside. If faucet exhibits very low flow: A. Remove and clean aerator (1) or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (2). When reinstalling parts, make sure bonnet nut (3) is tightened securely with a wrench.* Notice If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (3) is tight.
PAGE 10
75106 Rev.
PAGE 11
75106 Rev.
PAGE 12
Limited Warranty on Delta® Faucets Parts and Finish. All parts (other than electronic parts and batteries) and finishes of Delta® faucets purchased from authorized Delta sellers are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed.