Installation Guide

ManualsBrandsDelta ManualsKitchen Faucets19949-RBSD-DST

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

•ToREAD ALLwarnings,care,andmaintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien.

Models/Modelos/Modèles

9178-DST,9192-DST,9678-DST,

9992-DST,16971-DST,19922-DST,

19949-DST,19978-DST&19992-DST

Series/Series/Seria

2/13/14   Rev.Bwww.deltafaucet.com

ASMEA112.18.1/CSAB125.1

MEETSOREXCEEDS—ASMEA112.18.1/CSAB125.1

ALCANZAOEXCEDELASSIGIENTESNORMAS—

ASMEA112.18.1/CSAB125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS!/ADVERTENCIA: ¡SESTALLAVENOSEDEBEUTILIZAR

CONMAQUINASLAVAPLATOSPORTATILES!/AVERTISSEMENT: ONNE

DOITPASBRANCHERUNLAVE-VAISSELEPORTATIFSURCEROBINET!

LEROBINETESTCONFORMEOUSUPÈRIEURAUXEXIGENCESDES

NORMESSUIVANTES:ASMEA112.18.1/CSAB125.1

HIGH-RISE PULL-DOWN KITCHEN AND

BAR / PREP FAUCETS

LLAVES DE AGUA ELEVADAS, DESLIZABLES

HACIA ABAJO, PARA COCINAS Y BARES / PREP

ROBINET À COL DE CYGNE ET BEC-DOUCHETTE

POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE

1/8"(3.17mm)

85214

Summary of content (16 pages)

PAGE 1
HIGH-RISE PULL-DOWN KITCHEN AND BAR / PREP FAUCETS LLAVES DE AGUA ELEVADAS, DESLIZABLES HACIA ABAJO, PARA COCINAS Y BARES / PREP ROBINET À COL DE CYGNE ET BEC-DOUCHETTE POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE 85214 ASME A112.18.1 / CSA B125.1 Models/Modelos/Modèles 9178-DST, 9192-DST, 9678-DST, 9992-DST, 16971-DST, 19922-DST, 19949-DST,19978-DST & 19992-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
4 5 6 3 1 2 Maintenance If faucet exhibits very low flow A. Remove and clean aerator (1) (Note: some models require wrench (2) to remove aerator.), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). If faucet leaks from under handle: Remove handle (4) and cap (5). Using a wrench, ensure bonnet nut (6) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (6) is tightened securely with a wrench.
PAGE 4
Model / Modelo / Modèle 16971-DST RP50585▲ Set Screw & Button Tornillo de Presión y Botón Vis de calage et Bouton ▲ Specify Finish Especifíque el Acabado Précisez le fini RP40650 Set Screw Tornillo de Presión Vis de calage RP53435▲ Spray & Hose Assembly (Includes aerator) Rociador y Ensamble de la Manguera (Incluye el aireador) Douchette et Tuyau Souple (Inclut aérateur) RP60923 Friction Spacer Arandela de Fricción Rondelle de frottement RP51502▲ Cap Casquete Embase RP51503 Bonnet
PAGE 5
Model / Modelo / Modèle 19949-DST RP50786▲ Button Botón Bouton RP40650 Set Screw Tornillo de Presión Vis de calage ▲ Specify Finish Especifíque el Acabado Précisez le fini RP51502▲ Cap Casquete Embase RP60923 Friction Spacer Arandela de Fricción Rondelle de frottement RP60978▲ Spray & Hose Assembly (Includes aerator) Rociador y Ensamble de la Manguera (Incluye el aireador) Douchette et Tuyau Souple (Inclut aérateur) RP51503 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble de
PAGE 6
Models / Modelos / Modèles 19922-DST RP60977▲ Spray & Hose Assembly (Includes aerator) Rociador y Ensamble de la Manguera (Incluye el aireador) Douchette et Tuyau Souple (Inclut aérateur) ▲ Specify Finish Especifíque el Acabado Précisez le fini RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM Adaptadors 3/8”-24 UNEF to 1/2”-20 UN & 3/8”-24 UNEF to 1/2”-14 NPSM Adapteurs 3/8 po-24 UNEF to 1/2 po-20 UN et 3/8 po-24 UNEF to 1/2 po-14 NPSM RP53879▲ Button Botón
PAGE 7
RP50585▲ Set Screw & Button Tornillo y Botón Vis et bouton RP40650 Set Screw Tornillo de Presión Vis de calage Models / Modelos / Modèles 19978-DST, 9178-DST & 9678-DST ▲ Specify Finish Especifíque el Acabado Précisez le fini RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM Adaptadors 3/8”-24 UNEF to 1/2”-20 UN & 3/8”-24 UNEF to 1/2”-14 NPSM Adapteurs 3/8 po-24 UNEF to 1/2 po-20 UN et 3/8 po-24 UNEF to 1/2 po-14 NPSM RP51502▲ Cap Casquete Embase RP60923 Friction Spacer Arandela
PAGE 8
Models / Modelos / Modèles 9192-DST, 9992-DST & 19992-DST RP54234▲ Button Botón Bouton 9992-DST RP50815 Aerator & Wrench Aereador y Llave Aérateur et Clé RP60976▲ Spray & Hose Assembly (Includes aerator) Rociador y Ensamble de la Manguera (Incluye el aireador) Douchette et Tuyau Souple (Inclut aérateur) RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM Adaptadors 3/8”-24 UNEF to 1/2”-20 UN & 3/8”-24 UNEF to 1/2”-14 NPSM Adapteurs 3/8 po-24 UNEF to 1/
PAGE 9
1 19949-DST 19992-DST, 9992-DST & 9192-DST 19978-DST & 9178-DST 5 5 5 4 3 3 3 3 3 8 8 3 6 4 4 6 2 8 3 2 6 2 2 7 1 1 1 7 7 9 9 9 Models 19949-DST, 19992-DST, 9992-DST, 9192-DST, 19978-DST , 9178-DST & 9678-DST Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring. Tabs (4) on trim ring and base ring should be aligned together at the front and rear of the installation hole.
PAGE 10
Optional / Opcional / Facultative 16971-DST & 19922-DST 4 2 2 1 3 3 2 6 4 4 3 7 3 6 5 5 2 2 5 1 8 1 6 6 Optional Escutcheon Installation Model 16971-DST & 19922-DST Place gasket (1) into groove on bottom of faucet (2). Insert faucet tubes and mounting shank (3) through mounting hole. Install mounting bracket (4) and nut (5) onto the mounting shank using wrench (6). Not included with all models - To order see replacement parts page for your model.
PAGE 11
2 B. A. C. 3 3 2 4 1 3 4 Insert hose through spout tip only. Inserte la manguera solo a través de la punta del surtidor. 2 Introduisez le tuyau souple dans l’extrémité du bec seulement. 2 Hose Installation A. Insert hose guide (1) into end of hose (2) as shown. C. Slide spout assembly onto hub. Use caution not to pinch fingers. Rotate spout assembly to ensure smooth operation. B. Feed hose assembly (2) through spout (3) and hub (4). Instalación De la Manguera A.
PAGE 12
3 A. B. 2 1 1 2 2 1 1 2 3 2 3 1 Incorrect Installations. Hose Installation A. Slide hose weight (1) over end of hose (2). Instalacións incorrecta. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Installations incorrecte. Instalación De la Manguera A. Deslice la pesa de la manguera (1) sobre el extremo de la manguera (2). B.
PAGE 13
4 A. B. OR 2 2 1 O 2 OU 3 1 3 4 2 1 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 14
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 15
5 A. 6 2 B. 6 1 3 4 1 5 Soap Dispenser Installation Remove nut (1). Separate head (2) from body (3). Insert body (3) and gasket (4) through selected hole in sink. Make sure gasket (4) is properly seated in the base. Secure body to sink with nut (1). From under the sink screw the bottle (5) onto the body assembly shank. Insert pump (6) into head (2), then drop into body (3). NOTE: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle.
PAGE 16
B. 3 Function Wand Mango de 3 Funciones Poignée à 3 Fonctions 7 A 1 2 3 90º A B. Wand will lock into position when brought into proximity of the spout magnet. The sprayer can be removed by either pulling directly out from the spout or by twisting 90° in either direction which will cause the magnets to repel and the head to decouple from the spout (recommended). Check the operation of the 2 function wand by pushing the trigger (A) from aerator to spray.