Operating Guide

8
106643 Rev. A
SILICONE
A.
B.
D.
E.
A.
Remove stopper (1), brass nut & washer (2), black
gasket (3) and tail piece (4).
B.
Apply silicone to underside of flange (1). Insert
flange into sink.
C.
Install black gasket (1), washer and brass nut (2)
onto flange (3) from below sink, but do not tighten
brass nut (2). Screw on tail piece (4) and hand
tighten.
D.
With pivot (1) facing toward faucet, pull pop
up straight down into drain hole and secure
gasket (2), brass nut and washer (3). DO
NOT TURN POP-UP WHILE TIGHTENING
BRASS NUT OR SEALANT MAY NOT SEAL
DRAIN. Remove excess sealant.
Pop-Up with Metal Flange and Plastic Tail Piece
A.
Enlevez la bonde (1), l’écrou en laiton et la
rondelle (2), le joint noir (3) et le raccord droit
de vidange (4).
B.
Appliquez de composé à la silicone sous la co
lerette (1). Introduisez la collerette dans l’évier.
C.
Montez le joint noir (1), la rondelle et l’écrou en la
ton (2) sur la collerette (3) par dessous l’évier sans
serrer l’écrou en laiton (2).
Vissez le raccord droit
de vidange (4) et serrez-le à la main.
C.
F.
E.
Remove pivot nut (1). Install horizontal rod (2) and
stopper (3) as removable (4) or non-removable
(5). Hand tighten pivot nut (1).
F.
Attach horizontal rod (1) to strap (2) using clip
(3). Insert lift rod (4) into strap and tighten
screw (5). Connect assembly to drain (6).
A.
Quite el tapón (1), la tuerca de bronce y la arandela
(2), el empaque negro (3) y la pieza de cola (4).
B.
Aplique silicón por debajo de la brida (1).
Introduzca la brida dentro del lavamanos.
C.
Instale el empaque negro (1), la arandela y la
tuerca de bronce (2) en la brida (3) desde la parte
interior del lavamanos pero no apriete la tuerca de
bronce (2). Atornille la pieza de cola (4) y apriete
a mano.
D.
Con el pivote (1) de frente a la llave, hale el
desagüe automático directamente hacia abajo
dentro del drenaje y fije el empaque (2), la
tuerca de bronce y la arandela (3). NO GIRE
EL DRENAJE AUTOMÁTICO MIENTRAS
APRIETE LA TUERCA DE BRONCE O EL
SELLADOR PUEDA NO SELLAR EL
DRENAJE. Quite el exceso de sellador.
Drenaje automático con brida de metal y la pieza de cola plástica
E.
Quite la tuerca del pivote (1). Instale la barra
horizontal (2) y el tapón (3) como desmontable (4)
o fijo (5). Apriete a mano la tuerca del pivote (1).
F.
Conecte la barra horizontal (1) a la barra chata (2)
usando el gancho (3). Inserte la barrita del
desagüe (4) en la barra chata y apriete con el to
nillo (5). Conecte el ensamble al desagüe (6).
D.
Alors que le pivot (1) fait face au robinet, tirez
le renvoi directement vers le bas dans l’orifice
de l’évier, puis fixez le joint (2), l’écrou en lai-
ton et la rondelle (3). NE TOURNEZ PAS LE
RENVOI PENDANT QUE VOUS SERREZ
L’ÉCROU EN LAITON CAR LE COMPOSÉ À
LA SILICONE POURRA NE PAS ASSURER
L’ÉTANCHÉITÉ DU RENVOI. Enlevez
l’excès de composé d’étanchéité.
E.
Enlevez l’écrou du pivot (1). Installez la tige
horizontale (2) et la bonde (3) de manière que la
bonde soit amovible (4) ou non amovible (5).
Serrez l’écrou (1) du pivot à la main.
F.
Fixez la tige horizontale (1) au feuillard (2) à l’aide
de l’agrafe (3). Introduisez la tirette (4) dans le
feuillard et serrez la vis (5). Raccorder l’ensemble
au renvoi (6).
1
4
2
3
1
3
1
2
4
1
2
3
1
3
5
2
2
4
1
5
6
3
4