Installation Sheet

ManualsBrandsDelta Manuals8 inch Widespread Sink FaucetsZura 8 in. Widespread 2-Handle Bathroom Faucet with Metal Pop-Up in Polished Nickel

TWO HANDLE WIDESPREAD

BATHROOM FAUCETS

LLAVES DE LAVAMANOS

EXTENDIDAS DE DOS MANIJAS

ROBINETS À ENTRAXE LONG À

DEUX POIGNÉES POUR LAVABO

Model/Modelo/Modèle

3574-MPU-DST

Series/Series/Seria

ZURA

™

Para instalación fácil de su llave

Delta usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

3/32” (2.38mm)

07/16/2020 Rev. F

3/32" (2.38mm)

81597

www.deltafaucet.com

Summary of content (12 pages)

PAGE 1
TWO HANDLE WIDESPREAD BATHROOM FAUCETS 81597 LLAVES DE LAVAMANOS EXTENDIDAS DE DOS MANIJAS ROBINETS À ENTRAXE LONG À DEUX POIGNÉES POUR LAVABO Model/Modelo/Modèle 3574-MPU-DST Series/Series/Seria ZURA™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici. You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin: 3/32” (2.
PAGE 2
1 A. B. C. Top View / Vista superior / Vue de dessus 1 2 1 1 2 2 1 3 Top View of Anchors / Vista superior / Vue de dessus 1 1 2 1 1 A. Place black valve anchors (1) into the B. IMPORTANT: Align valve anchors (1) C. Locate two screws (1) in the top of each A. Coloque los anclajes negros de la B. IMPORTANTE: alinee las anclas de la C. Localice los dos tornillos (1) en la parte outermost left and right sink holes. Position the valve anchors in the center of the holes.
PAGE 3
2 A. B. C. 1 5 2 1 1 4 2 3 3 2 1 1 3 2 3 3 Correct End Valve Orientation La Orientación de la Válvula Extrema Bonne configuration de la soupape Hot/Caliente/Chaude 2 1 Cold/Fría/Froide 2 Open Abrir Ouvert Valves shown in closed position. Las válvulas en la posición cerrada. Soupapes montrées en position fermée. 4 A. The hot side valve assembly is labeled (1). Note: The hot B. With both cold and hot valve C. Place handle bases (1) over anchors and A.
PAGE 4
3 A. B. 5 2 7 4 1 4 6 4 5 2 8 4 4 3 2 3 9 1 finial (1) into spout slot (2) as shown. Rotate finial until it is aligned with A. Insert spout slot. Insert lift rod (3) into the bottom of the mounting shank (4) and thread B. Insert fitting (1) into Y-connector (2) until fully seated and secure with clip (3). Pull A. Inserte el pomo de remate (1) en la ranura del surtidor (2) como se muestra. Gire el pomo hasta B.
PAGE 5
4 A. B. OR 2 O 1 3 Standard Connections B. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) to supply valve connection (4). Turn nut until it feels snug. Then tighten nut at least 2 more turns with a wrench. Repeat for other tube. Turn on water, examine for leaks. A.
PAGE 6
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 NOTICE Failure to use plastic sleeve (ferrule) in the correct orientation will result in disconnection and possible water damage. 1. Determine desired length of supply tube (1). Leave 1" or 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (ferrule) (3) onto cut supply tube.
PAGE 7
A. B. E. D. C. 1 6,/ 1( ,&2 5 1 2 3 2 3 2 1 1 1 F. G. 4 5 2 2 H. 4 3 2 1 5 2 1 3 2 1 6 Metal Pop-Up A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place.
PAGE 8
6 A. To Change the Position of Handle Stop (5). Para cambiar la posición de el tope (5). Pour changer la position de la butée (5). 2 Cold Fría Froide Hot Caliente Chaude 1 2 2 2 3 La flecha va hacia el surtidor en lados calientes y fríos. 3 Arrow faces spout on both hot & cold sides. B. 5 4 6 Hot Caliente Chaude The Y-connector (5) should be positioned on either side of the lift rod strap and horizontal rod to avoid interference.
PAGE 9
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. LIMPIEZA Y CUIDADO DE SU LLAVE Tenga cuidado al ir a limpiar este producto. Aunque su acabado es sumamente durable, puede ser afectado por agentes de limpieza o para pulir abrasivos.
PAGE 10
81597 Rev.
PAGE 11
Notes/Notas 81597 Rev.
PAGE 12
Limited Warranty on Delta® Faucets Parts and Finish. All parts (other than electronic parts and batteries) and finishes of Delta® faucets purchased from authorized Delta sellers are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed.