For U.S.A. , Canada & Europe model Hi-Fi Component SERVICE MANUAL MODEL ADV-700 DVD SURROUND RECEIVER — TABLE OF CONTENTS — SAFETY PRECAUTIONS ................................................... 2 SPECIFICATIONS .............................................................. 2 DIAGNOSTICS OF OPTICAL PICKUP AND REPLACING TRAVERSE UNIT ..................................... 3~5 DISASSEMBLY ............................................................. 6~10 CAUTION IN SERVICING ..............................
ADV-700 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
ADV-700 DIAGNOSTICS OF OPTICAL PICKUP AND REPLACING TRAVERSE UNIT Make failure diagnostics of the Optical Pickup as follows. If the laser drive current becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced. The laser drive current is registered on the seal attached to the rear of the Mecha. Unit. In case of replacing the Pickup, change the whole part of the Traverse Unit. No mechanical adjustment is necessary after the replacement. Disc no read, unsteady playback, etc.
ADV-700 Note for Handling the Laser Pick-up The protection for the damage of laser diode. If you want to change the optical device unit from any other units, you must keep the following. (1) It should be done at the desk already took measures the static electricity in care of removing the OPU's (Optical device unit) connector cable. (2) Workers should be put on the "Earth Band". (3) It shold be done to add the solder to the short land to prevent the broken Laser diode before removing the 24P FFC cable.
ADV-700 Optical Pick-up Diagnostics and Replacement When repairing, carry out failure diagnostics by following the procedure described below. If the present value of the laser drive current is 50% up to initial value, it is the point of the pickup replacement. In case of the pickup replacement, replace the Traverse Unit with no adjustment. The initial value is indicated on the label on back side of Mecha. NO DISC indicated, Playback not smooth, etc.
ADV-700 DISASSEMBLY ( Follow the procedure below in reverse order when reassembling ) 1. Top Cover 1) Remove 4 screws 1 on both sides. 2) Remove 6 screws 2 on the rear panel. 3) Detach the Cover as shown in the arrow direction. 2 1 1 2 2 1 1 2. Front Panel 1) Remove 4 screws 3 from the bottom edge of the Front Panel. 2) Disconnect FFC, 3P Connector, and 5P Connector from the Main PWB. 3) Detach the Front Panel together with the Inner Panel as shown in the arrow direction. MAIN P.W.B.
ADV-700 3. DSP PWB 4 1) Remove 4 screws 4 fixing the DSP PWB. 2) Disconnect FFC x 3 from the DSP PWB. 4 4 4 FFC DSP P.W.B. 4. DVD Mecha. Unit 1) Remove 4 screws 5 on the DVD Mecha. Unit. 2) Disconnect FFC x 2, 14P Connector, and 9P Connector from the DVD Mecha. Unit. 5 14P Connector FFC FFC 9P Connector 5. Rear Panel 1) Remove the Cord Bush. 2) Remove 5 screws 6 , 20 screws 8 on the Rear Panel.
ADV-700 6. Video PWB 1) Disconnect FFC x 2, 11P Connector, and 3P Connector from the Video PWB. 2) Detach the Video PWB from the PWB Holder. 11P Connector (Europe Model) 3P Connector 10P Connector (USA, Canada Model) Video P.W.B. FFC P.W.B. Holder FFC 7. Main PWB 1) Remove 5 screws 9 and 1 screw 1 0 on the Main PWB. 2) Remove 6 screws 1 1 from the bottom of the Chassis. 3) Disconnect 8P, 4P x 2, and 3P Connector from the Main PWB. Main P.W.
ADV-700 TRAVERSE UNIT DISASSEMBLY (Follow the procedure below in reverse order when reassembling) Caution: The optical pickup can be damaged easily by static electricity charged on human body. Take necessary anti-static measures when repairing around the optical pickup. 1. Guide Clamp Bracket disassembly 1 (1) Remove 2 screws 1 . (2) Remove Guide Clamp Bracket to arrow direction. 2. Tray disassembly Guide Clamp Bracket Solder to Short-Circuit (DVD) (1) Remove to arrow direction.
ADV-700 3. Traverse Unit disassembly (1) Remove 24P FFC (CX241), 15P FFC (CX151), 5P PH WIRE (CX051) and 3P PH WIRE (CX031) connecting with from the DVD Main P.W.B. (2) Remove 4 screws of 2 fixing Damper. (3) Remove Traverse Unit to arrow direction. 24P FFC (CX241) 2 3P PH WIRE (CX031) 15P FFC (CX151) Damper DVD Main P.W.B. Note for disassembly Traverse Unit Slide gear Boss (1) When assembling, reverse the order of the above.
ADV-700 ELECTRICAL ADJUSTMENT The following adjustment is electrical adjustments. These adjustments are to be performed after replacing the printed circuit boards. 1. Video Output (Interlace) Adjustment Measurement Point Video Output Pin Terminal Adjustment Point VR701 Mode Color Bar 75% T12 Playback Disc DVD T -S01 Measuring Device: Oscilloscope 200 mV/div, 10 Ps/div Adjustment Value: 1000 mVp-p r20 mV For compatibility of video signal output. 1.
ADV-700 BLOCK DIAGRAMS 1 4 3 2 5 6 7 8 ADV-700 BLOCK DIAGRAM (1/2) (Mechanism section) 4M DRAM 24P FFC DVD DRIVE MECHA UNIT FRONTEND PROCESSOR [TA1293F] DISC SERVO PROCESSOR [TC9453F] 8M FLASH ROM [HY29F080T] 16M SDRAM x2 4M DRAM A HRESET ATAPI INTERFACE DVD DECODER [TC9469BF] DVD PROCESSOR [ES4408] B LD8~15 15P FFC 4ch MOTOR DRIVER [BA5952FP] DMO,TRD DRIVE CONTROL m-COM [TMP95CW64F] 5P PH 3P PH SPINDLE MOTOR DRIVER [AN8471] DMO 8 E2PROM [S24C01A] /RST I/O EXPANDER [HCT273
ADV-700 1 4 3 2 5 6 7 8 ADV-700 BLOCK DIAGRAM (2/2) (E2 ONLY) MUTE 1U-3359-3 1U-3359-1 UADV-7 (DVD ENGINE ) 1U-3359-5,6 MUTE BA4053(E2 ONLY) V MUTE Y DVD MECHA FRONT-END CIRCUIT C FL TUBE 15-ST-36GN MUTE MUTE ES4408 ML6427 MUTE DVD DSP A COMPONENT VIDEO BA7660(Europe model only) Europe model:SCART TERMINAL USA,Canada model:3P PINJACK A BA7660(Europe model only) DVD DECODER VIDEO FILTER FL DRIVER M66005FP CPU Cr Cb Y Y C V Y VCR IN C Y TV/DBS IN B C Y V.
ADV-700 LEVEL DIAGRAMS 1 4 3 2 FRONT 5 6 7 8 STEREO H.P.F. INPUT BUFF.AMP A/D IN REV. AMP A/D IN REV. AMP SW MIX AMP D/A OUT L.P.F. REV. AMP TONE BUFF. AMP E.VOL PRE. AMP POWER AMP + A M62446 (1/3) fc=80Hz.12dB/OCT TONE + CD IN − − A/D DSP D/A + other ch MUTING − − MUTING + FRONT SP OUT + config1:OFF config2:ON FROM SWch ATT H/P OUT (dB) 30 SP OUT 1.66V (0.35W/8Ω) 20 B D/A 0dBFS A/D 0dBPS 10 (200mV) 0 30.1dB -10dBFS CD IN -10dBPS 6dB -11.
ADV-700 1 4 3 2 5 6 7 8 SUBWOOFER A D/A OUT L.P.F. LINE AMP LINE AMP BUFF. AMP E.VOL PRE. AMP M62446 (3/3) FROM DSP D/A + MUTING − − MUTING + SW PREOUT B D/A 0dBFS C -10dBFS Config-2 To FRONT ch -20dBFS 7.5dB 2.9dB -30dBFS 6dB 3.3dB Config-1 Subwoofer PREOUT 75mV -18dB 18.
ADV-700 CLOCK FLOW 1 4 3 2 5 6 7 8 A A/D SWitch IC113 SN74HC244 DIR IC107 LC89055W CKOUT(13) BCK(14) LRCK(15) DATAO(16) (17) SW1 (3) (15) SW2 (5) (7) XMCK(20) ( 2) SW4 (13) SW3 SN74LV244A DSP CODEC IC109 CS49329 IC108 AK4527VQ MCLK(44) (25)SCLKN1,(28)CMPCLK SCLK(43) (26)LRCLKN1,(29)CMPREQ LRCLK(42) (22)SDATAN1 AUDATA0(41) (27)CMPDAT AUDATA1(40) AUDATA2(39) (18) X'TAL B (6)SDTI1 (7)SDTI2 (8)SDTI3 (39)MCLK C (4)BICK SW1 SW2 SW3 SW4 SW5 SW6 (5)LRCK DIR IN A/D IN ON ON ON OFF OFF
ADV-700 SEMICONDUCTORS P41/A17 51 P36/A14 54 P37/A15 P35/A13 55 P40/A16 P34/A12 56 52 P33/A11 57 53 P32/A10 58 P30/A8(/-/D7) VCC VSS 61 P31/A9 P27/A7(/D7/D6) 62 59 P26/A6(/D6/D5) 67 63 P23/A3(/D3/D2) 68 64 P22/A2(/D2/D1) 69 P24/A4(/D4/D3) P21/A1(/D1/D0) 70 P25/A5(/D5/D4) P20/A0(/D0/-) 71 65 P17/D15/INT5 72 66 P15/D13/INT3 P16/D14/INT4 73 P13/D11 P14/D12 74 M30624FG (MA: IC101) 75 Abbreviation ahead of IC No. indicates the name of P.W.B. DVD Main P.W.B. Main P.W.
ADV-700 Pin No.
ADV-700 Pin No. Port Name Symbol Function 72 D14/P16 89055 CSFLAG Signal change detect input from DIR 73 D13/P15 REMOTE IR remote control input 74 D12/P14 /SYR Reset output to RDS IC of tuner 75 D11/P13 INTREQ IN Open drain operation (L: output, H: switch to input) 76 D10/P12 4932 CE Serial comm. chip enable output to surround DSP 77 D9/P11 4932 RST Reset output to surround DSP 78 D8/P10 4527 CE Serial comm.
ADV-700 Vss LA3 LA2 LA1 LA0 NC NC Vcc Vss LWRHL# LWRLL# LD15 LD14 LD13 LD12 Vcc Vss LD11 LD10 LD9 LD8 LD7 LD6 LD5 Vss Vcc LD4 LD3 LD2 LD1 LD0 Vss LCS3# LCS2# LCS1# LCS0# Vcc Vss LOE# AUX7 AUX6 AUX5 AUX4 AUX3 Vcc Vss AUX2 AUX1 AUX0 VPP HA2 Vcc 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 16
ADV-700 Pin No. Pin Name I/O Function Pin No. Pin Name I/O Function 56 DMA 3 O DRAM address bus 108 YUV 2 O 8-bit YUV output 57 DMA 4 O DRAM address bus 109 YUV 3 O 8-bit YUV output 58 DMA 5 O DRAM address bus 110 YUV 4 O 8-bit YUV output 59 Vcc I 3.6V power supply 111 Vcc I 3.
ADV-700 Pin No. Pin Name I/O Function 156 Vss I 157 Vcc I 3.6V power supply 158 HA 2 I/O Host address bus 159 VPP 160 AUX 0 I I/O GND Peripheral protection voltage Auxiliary port, (SDATA) I/O 161 AUX 1 I/O Auxiliary port, (SCLK) O 162 AUX 2 I/O Auxiliary port, (VFD DATA) I/O 163 Vss I GND 164 Vcc I 3.
ADV-700 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 PDON2 PDOP2 PDON1 PDOP1 PESP PVSS PESV PPW CFC2 CFC1 VSS3 TESM8 TESM7 TESM6 TESM5 PLCK VDD3 NC NC BD15 BD14 BD13 VSS5 BD12 BD11 BD10 BD9 VSS3 BD8 BD7 BD6 BD5 BD4 BD3 BD2 BD1 BD0 VDD5 /BWU /BWL /BCAS /BRAS /BOE VDD3 TC9453F (DVD: IC505) to Driver from RF-Amp.
ADV-700 Pin No.
ADV-700 Pin No.
ADV-700 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 /RAS./CAS 3 16 BA8-0 SEDVD BD15-0 Buffer DRAM 256kw/128kw/64kw (4Mbit/2Mbit/1Mbit) /BWU./BWL /BOE (NC) VSS VSS VDD /RST ESTOUT /MINT /MWR VSS /WRD /WCE MA6 MA5 MA4 MA3 MA2 MA1 MA0 VDD VSS MD7 MD6 MD5 MD4 MD3 MD2 MD1 MD0 VSS SEDVD VDD ACHCK AD0 ABCK AZCK (NC) TC9469BF (DVD: IC508) 2 CSEL /PDIAG.
ADV-700 Pin No.
ADV-700 Pin No.
ADV-700 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P34/A12 P35/A13 P36/A14 P37/A15 P20/A16 P21/A17 P22/A18 P23/A19 P24/A20 P25/A21 P26/A22 P27/A23 VCC VSS(GND) AM8/16 P17/D15 P16/D14 P15/D13 P14/D12 P13/D11 P12/D10 P11/D9 P10/D8 P07/D7 P06/D6 TMP95CW64F-**** (DVD: IC511) P33/A11 P32/A10 P31/A9 P30/A8 P47/A7 P46/A6 P45/A5 P44/A4 P43/A3 P42/A2 P41/A1 P40/A0 P50/RD P51/WR P52/HWR (GND)VSS PA0/AN0 PA1/AN1 PA2/AN2 PA3/AN3/ADTRG PA4/AN4 PA5/AN5 PA6/AN6 PA7/AN7 VREFH 50 49 48 4
ADV-700 Pin No.
ADV-700 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 LDO1 MDI1 EQF EQB RFDC GND2 EQD NC Vcc2 VccO PSC FEB TEB DPDB VccR RFO RPP RPB RPO RPZ TA1293F (DVD: IC501) 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 DFTN NC NC NC NC NC FEO TEO NC LVL NC NC NC VccS RFSW NC NC NC NC VccP GNDP LDO2 MDI2 NC NC VrA Vrfi VrD Vdd DPAC DPBD DPD1 DPD2 SCB SCL SCD VRCK NC NC VCKF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
ADV-700 Pin No.
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Pin Name VDD DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ DQ6 DQ7 VDDQ L DQM WE CAS RAS Chip Select BA A10/AP A0 A1 A2 A3 VDD VSS A4 A5 A6 A7 A8 A9 N. C CKE CLK U DQM N.
38 RSET1 37 VREF 40 TTXREQ 39 SCRESET/RTC 42 CLAMP 41 TTX 48 CLOCK 47 GND 46 VAA 45 VSO ADV7172KST (DVD: IC701) 44 RESET 43 PAL_NTSC ADV-700 VAA 1 P0 2 36 COMP1 35 DAC A 34 VAA 33 DAC B P1 3 P2 4 P3 5 P4 6 P5 7 P6 8 P7 9 32 VAA 31 GND TOP VIEW 30 VAA 29 DAC C Terminal Function COMP2 23 DAC F 24 SDATA 21 RSET2 22 26 GND 25 DAC E VAA 19 SCLOCK 20 VAA 11 GND 12 ALSB 17 GND 18 28 DAC D 27 VAA GND 13 HSYNC 14 FIELD/VSYNC 15 BLANK 16 CSO_HSO 10 Pin No.
ADV-700 BA5952AFP (DVD: IC504) VINFC 1 CFCErr1 2 28 MUTE 27 BIAS 26 VINTK CFCErr2 3 Terminal Function Pin No. VINSL+ 4 25 CTKerr1 VINSL- 5 24 CTKerr2 23 VINLD VOSL 6 VNFFC 7 22 PreGND PreVcc 8 PVcc1 9 21 PVcc2 20 VNFTK PGND 10 19 PGND VOSL- 11 18 VOLD- VOSL+ 12 17 VOLD+ VOFC- 13 VOFC+ 14 16 VOTK15 VOTK+ Name Function Pin No. VINFC Focus driver input CFCerr1 Cap.connecting pin for error amp filter CFCerr2 Cap.connecting pin for error amp filter VINSL+ Op.
ADV-700 LC89055W (DS: IC107) LC89055W Terminal Function Pin No.
Pin No.
AVDD VREFH VCOM 36 35 34 DZF1 AVSS 38 37 P/S MCLK 40 39 DIF1/SCL/CCLK DIF0/CSN 42 AK4527BVQ (DS: IC108) 41 LOOP1 LOOP0/SDA/CDTI 44 43 ADV-700 SDOS 1 33 DZF2/OVF I2C 2 32 RIN+ SMUTE 3 31 RIN- BICK 4 30 LIN+ LRCK 5 29 LIN- SDTI1 6 28 ROUT1 SDTI2 7 27 LOUT1 SDTI3 8 26 ROUT2 SDTO 9 25 LOUT2 DAUX 10 24 ROUT3 DFS 11 23 LOUT3 AK4527BVQ 18 19 20 21 22 TST NC ADIF CAD1 CAD0 16 15 17 14 TVDD DVDD PDN 13 DVSS 12 NC DZFE Top View
ADV-700 SN74LV574APW (DS: IC103) SN74LVC574APW (DS: IC104) SN74LV244APW (DS: IC105) SN74LVC244APW (DS: IC112) SN74HCT244APW (DS: IC106, 113) ML6427 (D/V: IC310, 311) 17 VCCO RGB UNFILTERD CHANNEL SYNCIN A/B MUX 1 SYNCIN 2 CVINF A/Y2 3 CVINF B/Y3 4 GND 5 VCC 6 24 SYNCOUT 2 23 SYNCIN 22 VCCO CV 21 CVOUT 1/YOUT A 20 CVOUT /Y OUT B 19 GNDO 23 3 4 7 R IN B/Y5 8 R IN B/Y5 8 GIN A/Y6 9 G IN B/Y7 10 17 VCCORGB 16 G OUT /Y OUT D 10 BIN B/C2 12 13 SWAP CVF 9 MUX MUX TRANSCONDUCTANCE ERROR AMP 21
ADV-700 AD1854 (DS: IC401) Terminal Function Pin No.
ADV-700 BA7625 (D/V : IC 302, 303) BA7626 (D/V : IC 301) NJU4053B V (D/V: IC308) (Europe model only) Y1 1 Monitor OUT 1 GND 2 IN5 6dB 3 L GND 4 IN4 CTL E 5 6dB 6 Y0 2 Y0 15 CTL A Z1 3 Z1 14 OGIC VOUT1 7 CTL D 8 Y 15 Y X 14 X Z 4 Z X1 13 X1 Z0 5 Z0 X0 12 X0 12 IN2 Inhibit 6 A 11 A B 10 B VEE 11 CTL B Inhibit 7 C 9 C GND 8 10 VOUT2 L Y1 13 Vcc OGIC IN3 16 VCC 16 IN1 CTL C 9 BA7660FS (D/V : IC402, 403) (Europe model only) MUTE 1 INA 2 16 VCC 6dB 75W
ADV-700 LC72720NM (MA: IC106) 3 VREF 1 24 SYR MPXIN 2 23 CE Vdda 3 22 D1 Vssa 4 21 CL FLOUT 5 20 D0 COIN 6 19 RDS-1D T1 7 18 SYNC T2 8 17 T7 9 16 T6 T3 T4 10 15 Vddd T5 11 14 Vssd XOUT 12 5 4 1 REFERENCE VOLTAGE 2 ANTIALIASING FILTER 6 19 15 RDS DETECTOR ARI DETECTOR DIFFRENTIAL DECODER BIPHASE DECODER S W 14 SC-BANDPASS FILTER (57kHz) 11 10 COMPARATOR SMOOTHING FILTER D (Ð 90°) CLOCK RECOVERY (D-YCO) D-PLL (D-YCO) PC 9 8 D (Ð 0 °) 7 GROUP AND BLOC
ADV-700 M51957BFP (MA: IC104) TC74HC32AF (MA: IC102) 14 Vcc 13 4B NC 1 1Y 3 12 4A Input 2 2A 4 11 4Y NC 3 2B 5 10 3B 2Y 6 9 3A GND 7 8 3Y GND 4 Output: Open Collector 8 NC M51957BFP 1A 1 1B 2 Vcc 7 5 µA 7 Vcc 6 Output Input 2 6 Output 5 Delay-Cap 1.
ADV-700 PQ070XZ01Z (DVD: IC112) 4M DRAM (SOJ)-35 (DVD: IC507,509) IS41C16256 M11B416256A VCC 1 40 GND I/O0 I/O1 I/O2 I/O3 VCC I/O4 I/O5 I/O6 I/O7 NC NC WE RAS NC A0 A1 A2 2 39 3 38 4 37 5 36 6 35 7 34 8 33 9 32 10 31 11 30 12 29 13 28 14 27 15 26 16 25 17 24 18 23 I/O15 I/O14 I/O13 I/O12 GND I/O11 I/O10 I/O9 I/O8 NC LCAS UCAS OE A8 A7 A6 A5 19 22 20 21 A3 VCC 3 Name A0-A8 I/O0-15 WE OE RAS UCAS LCAS Vcc GND NC DC input (VIN) 1 On/Off control (VO) 2 TOP VI
ADV-700 TRANSISTORS 2SA1037K 2SB709A 2SC2412K 2SD601A KTC2875B B TOP VIEW C DTA114EK DTA144TK DTC114EK DTC114YK DTC143TK DTC144EK DTC323TK DTC Series DTA Series C C R1 R1 B B R2 R2 E E B TOP VIEW C R1 E 2SA1015 2SB562 2SC1740S 2SC2878 2SD1858 KTC2874B E R1 R2 DTC114EK DTC114YK DTC143TK DTC323TK DTA114EK 10kohm /Ω 10kohm /Ω DTA114ES 10kohm /Ω 10kohm /Ω − DTA114TK 47kohm /Ω DTC144EK 47kohm /Ω 47kohm /Ω DTA114ES KTA1659A 2SK771 S FRONT VIEW FRONT VIEW FRONT VIEW E C B E C B B
ADV-700 FL DISPLAY 15ST36GN (D/V: FL701) 45 46 90 Pin Assignment Pin No, Connection Pin No, Connection Note: 1. Fn: Filament 2. nG: Grid 3. Pn: Anode 4. NP: No Pin 5.
ADV-700 PRINTED WIRING BOARDS 1 2 4 3 5 6 7 8 GU-3333 DVD MAIN P.W.B.
ADV-700 1 2 3 4 5 6 7 8 A B C D E INTERNAL LAYER FOIL SIDE 48
ADV-700 1 4 3 2 5 6 7 8 1U-3358 MAIN P.W.B.
ADV-700 1 4 3 2 5 6 7 8 A 4 5 5 8 4 14 8 1 7 8 5 1 4 5 8 8 4 1 5 8 8 5 1 4 B 12 1 13 24 C 100 25 76 26 75 8 5 1 4 1 50 5 1 1 1 4 4 1 51 16 9 1 8 8 8 5 1 4 D E FOILSIDE 50
ADV-700 1 4 3 2 5 6 7 8 1U-3359 DISPLAY P.W.B.
ADV-700 1 4 3 2 5 6 7 32 8 1 A 33 64 14 8 16 9 1 7 1 8 B 16 9 16 9 1 8 1 8 C 7 1 8 14 24 13 1 12 8 1 9 16 24 13 1 12 8 1 9 16 D E FOIL SIDE 52
ADV-700 1 3 2 4 5 6 7 8 1U-3360 DSP P.W.B.
ADV-700 1 2 3 4 5 6 7 8 A 4 1 4 1 5 8 5 8 4 1 4 1 5 8 5 8 4 1 4 1 5 8 5 8 B C 8 5 1 4 8 5 1 4 D FOIL SIDE E 54
ADV-700 NOTE FOR PARTS LIST l Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. l When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying. l Ordering part without stating its part number can not be supplied. l Part indicated with the mark " " is not illustrated in the exploded view. l Not including Carbon Film ±5%, 1/4W Type in the P.W.Board parts list.
ADV-700 PARTS LIST OF P.W.B. UNIT GU-3333Z DVD MAIN P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP IC101 IC102 262 2811 002 IC ES4408F GEN 5274 ROM SUB ASS’Y(UADV7) IC HY29F080T Ref. No. Part No. Part Name Remarks R116-122 247 2009 941 Carbon chip 6.
ADV-700 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name R711 247 2018 903 Carbon chip 0ohm 1/16W RM73B--0R0K R713 247 2011 942 Carbon chip 47kohm 1/16W RM73B--473J 247 2012 996 Carbon chip 200kohm 1/16W RM73B--204J R715 247 2008 900 Carbon chip 1.8kohm 1/16W RM73B--182J R559 247 2009 925 Carbon chip 5.6kohm 1/16W RM73B--562J R716 247 2008 968 Carbon chip 3.3kohm 1/16W RM73B--332J R560 247 2009 941 Carbon chip 6.
ADV-700 Ref. No. C143-145 Part No. Part Name 257 0512 903 Ceramic chip 0.1uF/25V Remarks Ref. No. Part No. Part Name Remarks CK73F1E104Z C231 257 0509 929 Ceramic chip 1000pF/50V CK73B1H102K C232,233 257 0512 903 Ceramic chip 0.1uF/25V CK73F1E104Z C457,458 254 3053 910 Electrolytic 22uF/16V CE04D1C220MBP CK73F1H103Z C146 257 0509 929 Ceramic chip 1000pF/50V CK73B1H102K C147-149 257 0512 903 Ceramic chip 0.
ADV-700 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks Q'ty C580 257 0501 927 Ceramic chip 0.015uF/50V CK73B1H153K OTHER PARTS GROUP C582-589 257 0512 903 Ceramic chip 0.1uF/25V CK73F1E104Z CX031 205 0863 936 3P PH connector base (L) 1 C590,591 257 0507 976 Ceramic chip 330pF/50V CC73CH1H331J CX051 205 0863 952 5P PH connector base (L) 1 C592 254 4464 906 Electrolytic 100uF/6.
ADV-700 Note: 1U-3358/3358A MAIN P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks The symbols in the column “Remarks” indicate the following destinations. E3: U.S.A./Canada model E2: Europe model Ref. No. Part No.
ADV-700 Ref. No. Part No. Part Name R159 247 2010 985 Carbon chip 27kohm 1/16W R159 247 2011 942 Carbon chip 47kohm 1/16W Remarks Ref. No. Part No.
ADV-700 Ref. No. R703 Part No. Part Name 247 2007 943 Carbon chip 1kohm 1/16W Remarks Ref. No. RM73B--102J R770 Part No. Part Name Remarks 247 2007 943 Carbon chip 1kohm 1/16W RM73B--102J RM73B--751J R704 247 2012 925 Carbon chip 100kohm 1/16W RM73B--104J R771 247 2007 914 Carbon chip 750ohm 1/16W R705 247 2008 939 Carbon chip 2.4kohm 1/16W RM73B--242J R772 244 2043 982 Metal oxide 0.
ADV-700 Ref. No. Part No. Part Name Remarks C118 254 4536 915 Electrolytic 47uF/10V C119 257 0511 904 Ceramic chip 0.01uF/50V C120 254 4538 900 Electrolytic 10uF/16V CE04W1C100M (SMG/RE3) C121 257 0507 976 Ceramic chip 330pF/50V CC73CH1H331J C122 257 0511 904 Ceramic chip 0.01uF/50V Ref. No. Part No. Part Name C559 for E2 C566,567 257 0501 901 Ceramic chip 0.01uF/50V CK73B1H103K CK73F1H103Z C568 257 0501 901 Ceramic chip 0.
ADV-700 Ref. No. C733,734 Part No. Part Name 257 0511 917 Ceramic chip 0.022uF/50V Remarks Ref. No. Part No. CK73F1H223Z OTHER PARTS GROUP Part Name Remarks Q'ty C735 257 0503 925 Ceramic chip 10pF/50V CC73CH1H100D CW031 203 5270 007 3P PH-SAN connector cord 1 C736 257 0511 917 Ceramic chip 0.
ADV-700 1U-3359/3359A DISP/VIDEO P.W.B. UNIT ASS'Y Note: Ref. No. Part No. Part Name Remarks Q'ty RL701-704 214 0206 005 Relay (PCI212DM) 4 ST008,009 205 0452 017 Style pin 2 The symbols in the column “Remarks” indicate the following destinations. E3: U.S.A./Canada model E2: Europe model Ref. No. Part No.
ADV-700 Ref. No. Part No. Part Name Remarks R336 247 2006 960 Carbon chip 470ohm 1/16W RM73B--471J R337-339 247 2018 903 Carbon chip 0ohm 1/16W RM73B--0R0K R340 247 2005 903 Carbon chip 100ohm 1/16W RM73B--101J R341,342 247 2005 974 Carbon chip 200ohm 1/16W RM73B--201J R343 247 2013 908 Carbon chip 220kohm 1/16W RM73B--224J R344 247 2009 967 Carbon chip 8.
ADV-700 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks R721-723 247 2018 903 Carbon chip 0ohm 1/16W RM73B--0R0K C354 254 4538 939 Electrolytic 47uF/16V CE04W1C470M (SMG/RE3) R726,727 247 2009 983 Carbon chip 10kohm 1/16W RM73B--103J C355 254 4533 950 Electrolytic 470uF/6.3V CE04W0J471M (SMG/RE3) C356 257 0511 904 Ceramic chip 0.
ADV-700 Ref. No. C441 Part No. Part Name 257 0509 929 Ceramic chip 1000pF/50V C442 257 0512 903 Ceramic chip 0.1uF/25V C443 257 0511 904 Ceramic chip 0.01uF/50V Remarks Ref. No. Part No. Part Name Remarks Q'ty CK73B1H102K CY171 205 1006 080 17P FFC connector base for E3 CY902 205 0480 005 10P KR connector base (L) for E3 1 1 for E2 F905 206 1075 027 Fuse 1.6A for E2 1 CK73F1H103Z F905 206 1072 046 Fuse 2.
ADV-700 1U-3360 DSP P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP R104 247 2008 955 Carbon chip 3kohm 1/16W RM73B--302J IC101 262 2964 001 IC AT49LV002-70TC R105 247 2009 912 Carbon chip 5.
ADV-700 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks R401-403 247 2009 983 Carbon chip 10kohm 1/16W RM73B--103J C109,110 257 0512 903 Ceramic chip 0.1uF/25V CK73F1E104Z R404 247 2008 913 Carbon chip 2kohm 1/16W RM73B--202J C111 257 0511 904 Ceramic chip 0.
ADV-700 Remarks Ref. No. C195 Ref. No. 257 0506 951 Ceramic chip 100pF/50V Part No. Part Name CC73CH1H101J C634,635 C196 254 4522 916 Electrolytic 10uF/35V CE04W1V100M (SMG/RE3) C636 257 0501 927 Ceramic chip 0.015uF/50V CK73B1H153K C197 257 0511 904 Ceramic chip 0.01uF/50V CK73F1H103Z C637 254 4524 927 Electrolytic 0.33uF/50V CE04W1HR33M (SMG/RE3) C198-203 257 0512 903 Ceramic chip 0.
ADV-700 EXPLODED VIEW 1 4 3 2 5 7 8 Europe model U.S.A.
ADV-700 Note: PARTS LIST OF EXPLODED VIEW Ref. No. 1 1 1-1 1-2 1-3 1-4 1-5 1-6 2 2 2-1 2-2 2-3 2-5 2-6 2-7 2-8 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18 19 20 21 22 23 24 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Part No. 1U-3358 1U-3358A 1U-3359 1U-3359A 1U-3360 411 1984 309 146 2242 007 461 1066 002 443 9015 002 417 0611 105 412 4796 005 412 4791 107 412 4792 106 412 4793 008 254 6222 706 Part Name Main P.W.B. unit Ass’y Main P.W.B. unit Ass’y Main P.W.B. unit Reg. P.W.B.
ADV-700 PARTS LIST OF DVD MECHANISM UNIT Ref. No. 1A 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 21 22 23 24 26 27A 27B 23 27 28 29 30 31 32 33 34 35 37 38 39 40 42 43 44 46 47 63 23 25 36 41 50 53 54 55 56 57 58 Part No.
ADV-700 EXPLODED VIEW OF DVD MECHANISM 1 4 3 2 5 6 7 8 14 26 3 27B 46 A 47 26 32 47 31 30 63 8 32 44 38 2 33 43 34 12 37 B 15 39 28 50 42 43 54 35 21 36 51 29 1 23 27 51 6 21 53 50 50 40 51 5 C 23 51 7 49 24 49 11 49 48 58 23 24 55 24 56 49 25 24 57 9 10 17 23 41 D 68 24 16 27A 59 4 25 18 64 20 19 E 22 75
ADV-700 POINTS OF GREASING 1 2 3 4 5 6 7 8 A B C D E 76
ADV-700 PACKING VIEW Note: PARTS LIST OF PACKING & ACCESSORIES Ref. No. 201 202 203 203 204 206 207 207 208 209 210 Part No. 505 8092 010 503 1388 107 501 2138 101 501 2138 127 503 1409 002 505 0038 030 511 3774 008 511 3775 007 515 0867 101 511 3842 008 231 0922 009 Part Name Laminate envelope Cushion Carton case Carton case Sub cushion Poly. cover Instruction manual Instruction manual S.S. list (EX) Inst. Sheet Loop antenna Remarks for E2 for E3 for E2 for E3 Q'ty 1 2 1 1 1 1 1 1 1 1 1 Ref. No.
ADV-700 WIRING DIAGRAM 5 D-IN GND_D4 D-OUT +5V_D4 DSEL1 DSEL2 CX051(PH) STEREO /TUNED T.MUTE R OUT GND_A1 TU_L FM DET +12V_A1 +5V_D4 FM S.MATER GND_A1 DO CL DI CE 1 2 3 4 5 6 D-IN GND_D4 D-OUT +5V_D4 DSEL1 DSEL2 CY271(FFC P=1.25) CX211(FFC P=1.25) DVD-Y V.GND DVD-Cb V.GND DVD-Cr +5V V WIDE S-SEL D-SEL N.C. RGB_H +5V_V1 +5V_V1 AUDIO R GND_A1 AUDIO L GND_A1 +12V_A1 S-SEL WIDE C B A GND_V1 N.C.
ADV-700 MEASURING METHOD AND WAVEFORMS To check the waveforms on the Servo P.W.B., the GND ( (Except for Inner SW, TRVSW) ) probe of the oscilloscope to Vref point. NOTES Measuring Disc: DVD/DVDT-S01 CD/TCD-784 (It is better to use wires for extending between the probe and test points.) When watching the HF waveform, use the extending wire as short as possible. When HF waveform is noisy or cannot discriminate the eye-pattern, replace the Traverse Unit after measuring the Iop.
ADV-700 WAVE FORMS DVD PLAY (INNER) DVD PLAY DVDT-S01 1 0 DMO 1 HF (RFI) Vref 1 1 FG 1 2 A3 V = 0.5 V/div CD PLAY (INNER) CD PLAY TCD-784A 1 0 DMO 1 1 FG 1 2 A3 1 HF (RFI) Vref V = 0.
SCHEMATIC DIAGRAMS(1/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F + B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(1/8) 1 2 3 4 5 7 6 8 10 9 A 11 A B B C D E C D + B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(1/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F + B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(1/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F + B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(1/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F + B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(1/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F + B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(2/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(2/8) 1 2 3 4 5 6 7 8 10 9 11 A A B B C D E C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F + B LINE - B LINE SIGNAL LINE G WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(2/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(2/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(2/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(2/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(3/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(3/8) 1 2 3 4 5 6 7 8 10 9 11 A A B B C D E C D NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(3/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(3/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(3/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(3/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE SIGNAL LINE NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(4/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(4/8) 1 2 3 4 5 7 6 8 10 9 11 A A B B C D E C NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(4/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(4/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(4/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(4/8) 1 2 3 4 5 7 6 8 10 9 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(5/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(5/8) 1 2 3 4 5 6 7 8 10 9 11 A A B B C D E C NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: D F + B LINE SIGNAL LINE G Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(5/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(5/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(5/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(5/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(6/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power card is less than 460kohms, the unit is defective.
SCHEMATIC DIAGRAMS(6/8) 1 2 3 4 5 6 7 8 10 9 11 A A B B C D E WARNING: C Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. D CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.
SCHEMATIC DIAGRAMS(6/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power card is less than 460kohms, the unit is defective.
SCHEMATIC DIAGRAMS(6/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power card is less than 460kohms, the unit is defective.
SCHEMATIC DIAGRAMS(6/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power card is less than 460kohms, the unit is defective.
SCHEMATIC DIAGRAMS(6/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power card is less than 460kohms, the unit is defective.
SCHEMATIC DIAGRAMS(7/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE G NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(7/8) 1 2 3 4 5 6 7 8 10 9 11 A A B B C D E C D F + B LINE - B LINE SIGNAL LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(7/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE G NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(7/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE G NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(7/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE G NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(7/8) 1 2 3 4 5 6 7 8 10 9 11 A B C D E F + B LINE - B LINE SIGNAL LINE G NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(8/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(8/8) 1 2 3 4 5 6 7 8 10 9 11 A A B B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: C Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(8/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(8/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(8/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
SCHEMATIC DIAGRAMS(8/8) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.