ELECTRIC FIREPLACE MODELS: E36(L)(B)(H), E32(L)(B)(H) VE36(L)(B)(H) AND VE32(L)(B)(H) INSTALLATION INSTRUCTIONS AND HOMEOWNER’S MANUAL For more information, visit www.desatech.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH TABLE OF CONTENTS: PRODUCT FEATURES OPERATION ....…….………….. 6 SAFETY INFORMATION ……………………………..…… 2 INSTALLING OPTIONAL ACCESSORIES ...…………... 7 LOCATING FIREPLACE HEATER ………………………. 3 TROUBLE SHOOTING .………………………………….. 11 INSTALLATION CLEARANCES ……….………………… 3 TECHNICAL SERVICE .………………………………….. 13 PRODUCT SPECIFICATIONS ……………………………. 4 REPLACEMENT PARTS .........
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 3 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH LOCATING THE FIREPLACE HEATER INSTALLATION CLEARANCES Plan where to locate and frame the fireplace heater. This will save time and money later when you install the fireplace. Before installation consider the following: Minimum clearances to combustible are: 1. Where the firebox is located must allow for wall and ceiling clearances (see Installation Clearances).
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 4 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH PRODUCT SPECIFICATIONS E32 = 22 1/4" E36 = 24 1/4" ELECTRICAL SPECIFICATIONS Voltage: 120VAC, 60Hz 12.5 Amps Total Amps: 1500 Watts Total Watts: 1100 Watts Heater Rating: 100 Watts Max.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 5 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH ELECTRICAL INSTALLATION WARNING: Any electrical re-wiring of this appliance must be done by a qualified electrician. This wiring must be done in accordance with local codes and/or in the U.S.A. with the current, National Electrical Code ANSI/NFPA No 70 and in Canada with CSA C22.1 Canadian Electric code.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH HEARTH ASSEMBLY Before operating the appliance the lamp bulbs must be inspected and lava rock treatments, if desired, may be added as follows: RED 1. Lift the log bed off the hearth base to gain access to the lamp fixtures, (the log bed is attached with contact magnets only). 2. Turn the power on to the light circuit and check that all bulbs are operating.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 7 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH INSTALLING OPTIONAL ACCESSORIES OPTIONAL GLASS DOORS Models E36L, E32L, VE36L and VE32L may accept bi-fold glass doors that are fully operable or a fixed panel door that limit access to the fireplace, (see Accessories page 24). Installing BD36/32 Series Bi-Fold Glass Doors Follow these steps to install left and right operable panels: 1.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH OPTIONAL BRICK LINERS Installing/Removing BL36/32E(W) Brick Liner Kits Models (V)E36/32(L)(H) may accept optional BL36/32E(W) brick liner kits (see Accessories, page 24). The brick panels may be installed anytime after the fireplace installation is complete. Follow these steps to install left and right panels: 1.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 9 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH OPTIONAL HEATER ACCESSORY Continued HEATER/BLOWER. ASSEMBLY 1. Open the upper control door (see Figure 11, on page 6) and remove the 2 Phillips screws below heater grill. See Figure 19. 2. Remove 2 Phillips screws holding the control cover to the control panel inside the firebox (see Figure 20). 3.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH OPTIONAL HEATER ACCESSORY Continued CONTROL PANEL 13. Connect White heater wire to neutral connection marked ‘B’ or ‘A’ on terminal block. See partial wiring diagram, Figure 24. TERMINAL BLOCK 14. Connect Black heater wire to terminal marked ‘N-1’ on the heater power, switch (see Figure 25).
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 11 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH TROUBLESHOOTING The three most common causes of a malfunctioning heater are: Note: For additional help, visit DESA Technical Service web site at www.desatech.com Note: Before trouble shooting the system, make sure the power to the circuit from the breaker or fuse panel is turned ON. 1. Tripped circuit breaker or blown fuse. 2. Loose or burned out light bulb. 3.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH WIRING DIAGRAM MOTOR MOTEUR HEATER ASSEMBLY - ELECTRICAL DIAGRAM ASSEMBLAGE D'CHAUFFAGE - DIAGRAMME D'ÉLECTRIQUE CUTOUT WHT COUPECIRCUIT (BLANC) SPLICE CONNECTION (L'CONNEXION ÉPISSURE) WHT (BLANC) MALE CONNECTION (L'CONNEXION MÂLE) FEMALE CONNECTION (L'CONNEXION FEMELLE) BLK (NOIR) RED (ROUGE) CAUTION: DISCONNECT APPLIANCE FROM THE ELECTRICAL SUPPLY BEFORE REMOV
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 13 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH Removing/Replacing Control Door TECHNICAL SERVICE Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH BUSHINGS Servicing Control Panel The control panel can be serviced from inside the unit by removing the control cover on the inside of the firebox, follow steps 3 through 5 under Optional Heater Accessory, page 9. CONTROL COVER If the control assembly needs complete replacement, proceed to remove as follows: 1. Remove the glass doors (if equipped).
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 15 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH Accessing Imaging Unit 4 SCREWS @ HEARTH PANEL The imaging unit can be accessed from inside the firebox for servicing as follows: 1. Remove the glass doors (if equipped). See Optional Glass Doors, page 7. 2. Remove the screens, grate and brick liners. See Figure 32 and instructions under Optional Brick Liners, page 8). 3.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH BASE COVER VIEWING SCREEN Figure 36 – Removing Base Cover Figure 35 - Removing Viewing Screen WASHER M6 HEX NUT Servicing Fan Blower SPACER SLEEVE If the fan blower requires service, it may be removed as follows: 1. Remove the 3 light bulbs from the lamp fixtures (see Replacing Light Bulbs, page 13). 2. Disconnect the two 1/4" blade connectors at the motor unit. 3.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 17 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH FLAME CORD Servicing Flame Pennants If the flame pennants should become tangled or detached they may be reattaching or replacing as follows: 1. Locate the affected flame pennant and slip the hem at the base of the flame pennant over the proper hanger bracket position. See Figure 38 for proper location. 2.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH Replacing Reflective Ribbons If reflective ribbons become damaged or loose they may be replaced as follows: 1. Turn off all power to the appliance at the circuit breaker or fuse. SCREWS & WASHERS HANGER BRACKETS 2. Locate defective ribbons; there are 3 strips mounted on the rear cabinet and 3 mounted in the base. See Figure 39, page 17. 3.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 19 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH Further Accessing Imaging Unit For Replacement The imaging unit can be removed from inside the firebox for servicing as follows: 1. Remove 4 Hex screws on the lower louver panel and detach the louver assembly from the front face. See Figure 41, page 18. 2.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH ILLUSTRATED PARTS BREAKDOWN Models: E36L, E36LB, E36LH and E32L, E32LB, E32LH and VE36L, VE36LB, VE36LH VE32L, VE32LB, VE32LH E36LBH E32LBH and VE36LBH and VE32LBH 17 29 7 7 28 27 FIREPLACE ASSEMBLY 26 31 6 32 30 33 20 7 18 24 34 17 7 14 7 37 25 38 21 23 20 22 35 36 19 22 22 39 18 12 7 3 11 7 41 17 10 15 9 16 13 6 14 8 7 5 42 4 2
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 21 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH PARTS LIST KEY * E36LB NO.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 22 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH ILLUSTRATED PARTS BREAKDOWN Models: E36L, E36LB, E36LH and E32L, E32LB, E32LH and VE36L, VE36LB, VE36LH VE32L, VE32LB, VE32LH 14 E36LBH E32LBH and VE36LBH and VE32LBH 11 16 15 1 2 12 13 26 9 27 18 3 10 4 5 28 17 29 23 21 7 25 21 23 22 24 IMAGING UNIT 8 19 6 19 20 16 19 32 16 31 43 30 18 40 39 41 42 45 33 36 45 38 38 37 46 35 34
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 23 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH PARTS LIST KEY * E36LB NO.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH ACCESSORIES Purchase these firebox accessories from your local dealer. If they can not supply these accessories, call DESA Sales Department at 1-866-672-6040 for information. You can also write to the address listed on the back page of this manual.
ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS 25 Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH INSTALLATION NOTES For more information, visit www.desatech.
WARRANTY INFORMATION KEEP THIS WARRANTY Model Serial No. Date Purchased Always specify model and serial numbers when communicating with the factory. We reserve the right to amend these specifications at any time without nitice. The only warranty applicable is our standard written warranty. We make no other warraty, expressed or implied.