Instructions / Assembly

ManualsBrandsDesign House ManualsKitchen ApplianceEden 2-Handle Bar Faucet in Oil Rubbed Bronze

• ALWAYS protect your eyes with safety glasses.

SAFETY TIPS

IMPORTANT POINTS

Helpful tools to install this faucet:

•

basin wrench

•

Teflon tape

•

(2) crescent wrenches

•

silicon sealer

•

flashlight

•

faucet supply tubes

Models 524751, 524777

TWO HANDLE

LAVATORY FAUCET

Design House is a registered

brand of DHI Corp.

Mequon, WI 53092

1-800-558-8700

Your new Design House faucet will give you years of trouble free performance.

Thank you for choosing a Design House product for your home.

Please read all of these instructions carefully before installing your new faucet.

• When installing your new faucet, hand tighten the connector nuts, then use one wrench to anchor

the fitting and a second wrench to tighten the nut one additional turn. Connections that are too tight

will reduce the integrity of the system.

• Wrap all threaded connections (except aerator thread in spout) with Teflon tape available from your

local hardware or plumbing supply store. Always wrap in a counter-clockwise direction.

MAINTENANCE

INSTALLATION PROCEDURE

Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the

amount of lead used in brass and solder. Your new faucet is made in strict compliance with

all government standards. The materials used in the manufacture of this faucet are of industry

standard quality and are similar to other plumbing products having brass fittings.

To reduce the amount of lead in your drinking water, allow the water to run for a moment before

filling your glass and remember to always use cold water for drinking purposes.

CONSUMER PROTECTION WARNING

Your new Design House faucet is designed to give you years of trouble free performance. Keep it

looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh

chemicals that will dull the finish and void your warranty.

Brass finishes are polished, then protected with a lacquer coating to help prevent tarnishing. Clean

these surfaces only with a damp, soft cloth.

1. Shut off water supplies.

Remove old faucet.

Place gasket (1A) on bottom

of new faucet.

Place faucet though mounting

holes in sink. Secure faucet to

sink using mounting nuts (1B)

provided.

2. Make connections to water

lines.

Use 1/2" IPS faucet

connections (2A) or use the

supplied coupling nuts (2C)

with 3/8"O.D.ball-nose risers

(2B).

Use wrenches to tighten

connections.

Do not overtighten.

3. Important: After installation is

completed, remove aerator.

Turn on water supply and

allow both hot and cold water

to run for at least one minute

each.

While water is running, check

for leaks.

Replace aerator.

1 2 3

Summary of content (2 pages)

PAGE 1
Design House is a registered brand of DHI Corp. Mequon, WI 53092 1-800-558-8700 TWO HANDLE LAVATORY FAUCET INSTALLATION PROCEDURE 1. Shut off water supplies. 2. Make connections to water lines. Remove old faucet. Use 1/2" IPS faucet Place gasket (1A) on bottom connections (2A) or use the of new faucet. supplied coupling nuts (2C) Place faucet though mounting with 3/8"O.D.ball-nose risers holes in sink. Secure faucet to (2B). sink using mounting nuts (1B) Use wrenches to tighten provided. connections.
PAGE 2
TROUBLE SHOOTING Problem: Faucet leaks from under handle. Cause: Bonnet is loose or o-ring on cartridge is dirty or twisted. Action: 1. Move handle to OFF position. Unscrew the set screw on the side of the handle seat. Then remove the entire handle assembly. 2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON position. The leak should stop around the cartridge stem. 3. If the leak does not stop, shut off the water supply. Remove the bonnet by turning it counter clockwise.