Product Description
ba
<5mm
Frame
Window/
Door
a.
b.
c.
d.
e.
f.
3. Release the button while the LED is ashing
numerous times in a row.
4. After you release the button, the LED shows
one long ash, and the reset is completed.
eng
Modes
ACTIVATION MODE
A single green ash means that the sensor and
the magnet are moving either away from or to-
wards each other.
SEARCHING GATEWAY MODE
Red ashes every second for a longer period,
means that the device is searching for a gate-
way.
LOST CONNECTION MODE
When the red LED ashes 3 times, it means that
the device has failed to connect to a gateway.
LOW-BATTERY MODE
Two consecutive red LED ashes every 60
seconds, means that the battery should be
replaced.
• There are many ways to mount the sensor
and magnet, as windows and doors vary
greatly. The most important consideration is
for the magnet to be placed as near to the
point on the sensor indicated by the grey
arrow.
• The sensor and magnet may be placed on
separate three dimensional planes, though
this does aect the maximum distance
allowed. The magnet may also be placed
either facing the side of the sensor or sitting
parallel to it.
Other information
Note local regulations about information to your
insurance company regarding installed Window
Sensors.
Resetting
Resetting is needed if you want to connect your
Window Sensor to another gateway or if you
need to perform a factory reset to eliminate ab-
normal behavior.
STEPS FOR RESETTING
1. Press and hold down the reset button for
approximately 8-10 seconds.
2. While you are holding the button down, the
LED rst ashes once, then two times in a
row, and nally numerous times in a row.
Mounting
• Clean the surface before mounting.
• The Window Sensor (a) should be mounted
to the frame using the double stick tape,
already applied on the back of the sensor
and magnet. Press rmly to secure sensor.
Testing
You can test if the positioning of the sensor and
magnet are correct by checking whether the
green light on the Window Sensor is ashing
when you open or close the window/door.
Placement
• Place the sensor indoors at a temperature
between 0-50°C.
• The magnet has to be placed on that side
of the sensor which is marked with a small
triangle.
• The magnet and sensor also have to be
aligned/centered thickness-wise on as
similar level as possible.
• In case of a weak or a bad signal, change the
location of the Window Sensor or strengthen
the signal with a smart plug.
SEE PAGE 2 FOR ILLUSTRATIONS
• When removing cover for battery change -
electrostatic discharge can harm electronic
components inside.
• Always mount indoors as sensor is not
waterproof.
• Do not place the sensor close to magnetic
or electromagnetic elds. This device
includes a magnet. The magnet creates
a magnetic eld that may cause damage
to computer hard drives, magnetic cards,
data storage devices, hearing aids and
speakers e.g. Therefore, we strongly advise
you to never position the magnet close to
electronic devices.
Getting started
1. Open the casing of the device by pushing
the fastening on top of the device to remove
the front panel from the back cover.
Product description
The Window Sensor detects and reports open-
ing and closing of doors and windows. Easily
installed on any door or window, the sensor trig-
gers a signal when parted. This lets you know
when a room is entered, if a window or a door
has been left open, etc.
Window Sensor
Fault nding
• If the Window Sensor does not work when
the window or door is parted, the probable
cause is a faulty battery. Replace the
batteries if they are worn out.
• In case of a bad or weak signal, change
the location of the Window Sensor.
Otherwise you can relocate your gateway
or strengthen the signal with a smart plug.
• If the search for a gateway has timed out, a
short press on the button will restart it.
Battery replacement
CAUTION: RISK OF EXPLOSION IF BATTER-
IES ARE REPLACED BY AN INCORRECT TYPE.
DISPOSE OF THE BATTERIES IN ACCORD-
ANCE WITH INSTRUCTIONS.
2. Insert the enclosed batteries into the device,
respecting the polarities
3. Close the casing
4. The Window Sensor will now start
searching (up to 15 minutes) for a Zigbee
network to join.
5. Make sure that the Zigbee network is open
for joining devices and will accept the
Window Sensor.
6. While the Window Sensor is searching for
a Zigbee network to join, the red LED is
ashing.
Disposal
Dispose the product and battery properly at the
end of life. This is electronic waste which should
be recycled.
Precautions
• The magnet (b) should be mounted on the
door or window no further than 5mm away
from the arrow on the sensor.
7. When the red LED stops ashing, the
Window Sensor has successfully joined the
Zigbee network.
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside
1. Open the casing of the device by pushing
the fastening on top of the device to remove
the front panel from the back cover.
2. Replace the batteries respecting the
polarities. The Window Sensor uses 2xAAA
batteries.
3. Close the casing.
4. Test the Window Sensor.
INSTALLATION MANUAL
Version 4.2
The reset button is marked with the small ring
on the front of the sensor.
Placement Examples - Top View
• The most benecial distance between the
sensor and the magnet is 0.2-0.5 cm.
• Be aware that on magnetic surface (e.g.
metal door), the distance between the
sensor and the magnet has to be 0.1-0.3 cm.